Bentel Security KYO Series Operating instructions

KYO
Unit
PROGRAMMING
FROM KEYPAD
®
MADE
IN
ITALY

®®
BENTEL SECURITY srl reserves the right to modify the technical specifications of this product without prior notice.
KYO 4 M – KYO 8 M – KYO 32 M – KYO 4 P – KYO 8 P – KYO 32 P
KYO 8G P-SW1 – KYO 8G P-SW2 – KYO 32G P-SW1 – KYO 32G P-SW2
Hereby, Bentel Security, declares that the above mentioned Control Panels are in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
The complete R&TTE Declaration of Conformity for each Panel can be found at
www.bentelsecurity.com/dc.html.
These Control Panels comply with CEI 79-2 2aed. 1993.
Installation of these systems must be carried out strictly in accordance with the instructions
described in this manual, and in compliance with the local laws and bylaws in force.
The above mentioned Control panels have been designed and made
to the highest standards of quality and performance.
The manufacturer recommends that the installed system should be completely tested at least once a month.
BENTEL SECURITY Srl shall not assume the responsibility
for damage arising from improper application or use.
The above mentioned Control panels have no user-friendly components, therefore,
should be serviced by authorized personnel only.
IMPORTANT: The following information is for disassembled Control Panels ONLY.
Ensure that the Manual you are using corresponds to that requested on the “RELEASE
ISSUES” label (see below) inside the package. Upgrades of the required KYO Unit Soft-
ware Release are also suitable.
Manual Release
Firmware Release
Software Release
RELEASE ISSUES
OK32 1.00 EN
Installation Manual
User Manual
Keypad Prog. Man.
Main Unit Manual
Kyo Unit Software
1.1
1.1
1.1
1.1
5.10
If the Manual/Kyo Unit Software release does not correspond, DO NOT attempt to assem-
ble and install the Control Panel until you have the required release.
The Manual Release Number of each Manual is shown at the bottom of the last page,
between the Code and Date, ad indicated in the figure below.
ISTPTBLEUNKYO 190303 P70
1.1
Manual
Release
Number
DateCode

3
®®
TABLE OF CONTENTS
Programming from the Keypad .................................... 4
Introduction ......................................................................................... 4
Code Limitations ..................................................................... 4
Accepted Keypads ................................................................... 5
Enrolling an LCD Keypad at address 8 .................................. 6
Adjusting Contrast, Brightness and Volume (MIA-S/MIA-D) ......... 6
The Liquid Crystal Display (LCD) ........................................... 7
Customizing the System .................................................................... 8
Programming ...................................................................................... 9
Exiting Programming ............................................................... 9
Actions ...................................................................................... 9
Zones...................................................................................... 10
Outputs ................................................................................... 12
Times...................................................................................... 13
Installer Code ......................................................................... 14
Keys ........................................................................................ 14
Key/Card option ............................................................ 14
Wireless option.............................................................. 15
Codes ..................................................................................... 16
Readers ................................................................................. 17
Keypads ................................................................................. 18
Program option ............................................................. 18
Language option ........................................................... 18
Date/Time ............................................................................... 19
Timers .................................................................................... 19
Telephone .............................................................................. 20
Teleservice ............................................................................. 21
Test Ev. ................................................................................... 21
Events ..................................................................................... 22
Options ................................................................................... 23
Strings .................................................................................... 24
Default .................................................................................... 25
Input Expanders (only for Series 32 Models) ....................... 26
Output Expanders (only for Series 32 Models) ..................... 26
Notes .............................................................................. 27

4Multifunction Control Panel
®®
PROGRAMMING FROM THE KEYPAD
Introduction
You can program the system using the ‘KyoUnit’ Software Application and a
computer (refer to the “INSTALLATION MANUAL”), or using the LCD
Keypad.
This manual contains instructions regarding system programming via Keypad.
For information regarding the system parameters, refer to ‘PROGRAMMING
FROM PC’ in the ‘INSTALLATION MANUAL’.
Code Limitations
The INSTALLER Code can set up and program the system, but cannot
program the PINS of the 24 User Codes.
MAIN USER Codes can program the PINs of User Codes (not Main User
Codes) that operate on their Partitions.
In the Table below, Code 1 is a Main User Code, and is assigned to Partitions 1,
3 and 4. Therefore, it can program its own PIN (Code 1) and the PINs of: User
Code 3 (assigned to Partitions 1 and 3), User Code 4 (assigned to Partition 4),
User Code 5 (assigned to Partitions 3 and 4) and User Code 7 (assigned to
Partition 3).
Code 2 is a Main User Code assigned to Partitions 2 and 3. Therefore, it can
program its own PIN, and the PINs of: Code 6 (assigned to Partition 2), User
Code 7 (assigned to Partition 3), User Code 8 (assigned to Partitions 2 and 3).
Table 1 - An example of Code programming
Code Number Code Type Assigned Partitions
Code 1 Main User 1 - 3 - 4
Code 2 Main User 2 - 3
Code 3 User 1 - 3
Code 4 User 4
Code 5 User 3 - 4
Code 6 Patrol 2
Code 7 Duress 3
Code 8 User 2 - 3

5
®®
Programming from the Keypad
Table 2 - OMNIA/TAST-R and MIA keypads
OMNIA/TAST-R MIA-S or MIA-D
Keys Superkeys Cursors
111or
ÌÍ
222or
Pp
333
or
ÀÁ
44
55
66
77
88
999or
C
000or
D
AAA
BBB
ee
OO
oo
EE
Accepted Keypads
You can program the system using OMNIA/TAST-R, MIA-S and MIA-D
Keypads. The function keys on these Keypads differ slightly, Table 2 shows
the Key Equivalence on the various Keypads.
Read this section carefully so you know how to operate your system from the Keypad.
NOTE: The ‘Superkeys’ (function keys) must be programmed, otherwise, they
will NOT work.
The following Table shows the ‘Superkeys’ (function keys) on the various Keypads.
The functions provided by holding down keys 11
11
1, 22
22
2and 33
33
3for approximately
3 seconds on the OMNIA/TAST-R, are provided by pressing contemporarily
keys ÌÍÌÍ
ÌÍÌÍ
ÌÍ, PpPp
PpPp
Pp or ÀÁÀÁ
ÀÁÀÁ
ÀÁ on the MIA-S and MIA-D.
The scroll function (cursor) provided by keys 99
99
9and 00
00
0on OMNIA/TAST-R,
is provided by keys CC
CC
Cand DD
DD
Don MIA-S and MIA-D Keypads.

6Multifunction Control Panel
®®
Enrolling an LCD Keypad at Address 08
To enroll an LCD Keypad at Address 08 from a LED Keypad, enter:
for KYO 32 Series: <Installer Code> + EE
EE
E+ 00
00
0
for KYO 4 - 8 Series: <Installer Code> + EE
EE
E
A short beep will indicate that the LCD Keypad has been enrolled.
NOTE - Before connecting the LCD Keypad — using the DIP switches [51],
enroll it at Address 8 (refer to Table 2.1 or 2.2 in the INSTALLATION
MANUAL).
This procedure will allow you to change the Control panel parameters when:
!You DO NOT have the Programming Software, or the system was
previously programmed using an LCD Keypad that has since been removed.
!The system is equipped with LED Keypads only (this type of keypad
cannot be used to program the Control panel).
Before ending the Programming session, DISABLE the Keypad at Address 8 or,
re-enable the LED Keypad—if previously Disabled (refer to the “Keypads”
paragraph in this section).
Adjusting Contrast, Brightness and Volume (MIA-S/MIA-D)
You can change the Display Contrast and Brightness, and the Buzzer Volume.
Changes can be made during Standby status only.
"Brightness Press and hold AA
AA
Ato increase Brightness
Press and hold BB
BB
Bto decrease Brightness
"Contrast Press and hold CC
CC
Cto increase Contrast
Press and hold DD
DD
Dto decrease Contrast
"Volume You can select 3 volume levels: High, Medium and Mute.
Press ee
ee
euntil you find the required Volume level.
!Long high Beep = High Volume
!Long low Beep = Average Volume
!Short low Beep = Mute

7
®®
Programming from the Keypad
13572468
Date
Partitions Status
Time
Troubles, Tampers, Controls
Figure 1 - An example of the Display during Standby status
The Liquid Crystal Display (LCD)
During Standby status the display will show:
1st line: Date and Time
2nd line: Partition status (4 or 8 Partitions depending on the system). This line
will also show:
"Trouble and Tamper — ûû
ûû
ûwill be shown above the relative icon;
"Special Functions — **
**
*will be shown above the relative icon ( tor r);
"Telephone Line status — ÿwill be shown above the iicon.
In the example in Figure 1, Partition 3 is armed, the 24h Tamper line is in
Alarm status, Teleservice is enabled and the Telephone line is busy.

8Multifunction Control Panel
®®
The Installer’s Code will allow you to access the INSTALLER MENU and
program the following options:
!Actions (Event Logger, Zones Status, Test Siren, Clear Call Queue)
!Zones
!Outputs
!Times (Entry/Exit Times)
!Inst.Cod (Installer Code)
!Keys (Key/Card and Wireless)
!Codes (User Codes)
!Readers (Key/Card Readers)
!Keypads (Keypads and Language)
!Date/T. (Date and Time)
!Timers (Scheduler)
!Teleph. (Telephone numbers)
!Teleser. (Teleservice)
!Test Ev. (Test Call)
!Events
!Options
!Strings (Descriptions)
!Default (Restore Factory Default)
!Exp. IN (Expander IN)—this option is available ONLY on Series 32 Models
!Exp. OUT (Expander OUT)—this option is available ONLY on Series 32 Models
Before starting the Programming session Disarm all Partitions.
If the system operates with LED Keypads only — before starting the
Programming session, enroll an LCD Keypad as described in the “Enrolling
an LCD Keypad at address 8”.
To access programming proceed as follows:
1.From Standby status, enter the Installer code
(0025 at Default), then press EE
EE
E.
2. Select the required option from the
PROGRAMMING Menu.
When you access PROGRAMMING, the Control panel will:
a) lock all Keypads, other than the one in use;
The locked Keypads will show the message
“PROGRAMMING”, and all the indicators (I, a
and G) will turn OFF.
b) clear the alarm memory;
c) force all the outputs (Alarm and Open Collector) to standby status;
d) stop the event evaluation;
e)if necessary — interrupt the ongoing call, and put the Call queue on hold;
f) activate the Plight (slow blink) on LED Keypads.
Customizing the System
Installer Menu Options
Input
Code *-----
PROGRAMMING
Actions âá
Accessing the
Installer Menu
PROGRAMMING

9
®®
Programming from the Keypad
Programming
eand E
NOTE: The examples in this section refer to the Kyo32 display (8 Partition
Control panel). Therefore, if you are not using a Kyo32 system, the display
messages may be slightly different.
Use the ee
ee
ekey to step back at any point on the Installer Menu,
Use the EE
EE
Ekey to confirm entered data.
Actions
This option provides a further 4 sub-options:
a)Test Siren — this option will allow you to Test the Alarm Output relay.
b)Zones Status — this option will allow you to Bypass / Unbypass zones
c)Event Logger — this option will allow you to view the events in the Logger.
d)Clear Call Queue — this option will allow you to interrupt ongoing calls,
and stop the call queue.
You can find a full description of this options in the ‘Operating from a
Keypad’ section in the ‘USER MAUAL’.
If you enter a Wrong Code the display will show an
error message, and go back to Standby status.
Exiting Programming
To exit Programming:
1. Press ee
ee
e(as many times as necessary) to step back on the menu;
2. Press EE
EE
Ewhen the ‘Sure?’ message is shown.
If, at this point, you do not wish to exit the menu,
press ee
ee
eto continue.
When you exit the PROGRAMMING Menu the Control panel will:
a) unlock all Keypads;
b) clear the Zone-cycle counter (refer to the ‘Zones’ paragraph);
c) clear BPI, Tamper and False Key/Card Alarms;
d)if the Panel is open — ignore the ‘Open Panel’ signal until it is closed again.
e)if necessary — restart the Call queue, starting from the interrupted call
(this does not apply to Teleservice calls).
PROGRAMMING
Sure ?
WRONG CODE
Wrong Code

10 Multifunction Control Panel
®®
Zones
1. From the Installer Menu, using 99
99
9or 00
00
0, select
the Zones option, then press EE
EE
E.
2. Using 99
99
9or 00
00
0, select the Zone, then press EE
EE
E.
3. Using 99
99
9or 00
00
0, select the Type, then press EE
EE
E.
4. Using 99
99
9or 00
00
0, select the required Attribute.
Press OO
OO
Oto Enable, or oo
oo
oto Disable the selected
Attribute, then press EE
EE
Eto continue.
If you select the Wireless attribute (available
ONLY on Series 32 Models), work carefully
through steps 5a, 5b and 5c, otherwise, go to
step 6.
5a. Using the number keys, enter the ESN of the
Wireless device.
!Use AA
AA
Aor BB
BB
Bto move along the row.
!Use OO
OO
Oor oo
oo
oto enter letters Athrough F.
NOTE - To change a Wireless zone back to a Hardwired zone, first zero
the ESN of the zone device (000000) before reprogramming it as a
Hardwired zone.
Press EE
EE
Eto go to the next step.
5b. Enable or Disable the Supervisory attribute.
Press EE
EE
Eto continue.
5c. Perform the Placement Test to verify that the
wireless device is in range of the VectorRX
Receiver. To perform the Placement test create a tamper condition (refer to
the Wireless Device instructions sheet).
One of the following values will be shown on the display:
!Bad!
!Fair!
!Good!
Values Fair! and Good! are positive values, whereas Bad! is a negative value.The
Placement can be considered suitable after 3 consecutive positive values.
To repeat the Placement Test, press ee
ee
eand repeat steps 5b and 5c.
GNo wireless device should be mounted without first performing a
Placement Test.
Press EE
EE
Eto go to step 6.
Zones
Zone 2 âá
PROGRAMMING
Zones âá
Selecting the Zone
Zone 2
Path âá
Zone 2
Reserved OFF âá
Type
Attribute
Zone 2
000000
Zone 2
Superv. OFF
Wireless
Supervisory
Zone 2
Test
Placement Test
Zone 2
Wireless ON âá
Zone 2
Good!

11
®®
Programming from the Keypad
Cycle (Vibration)
Table 3 - PULSE/TIME for the 'Roller Blind' attribute
Sensitivity PULSE TIME
1 ... 5 1 ... 5 30 seconds
6 ... 10 1 ... 5 2 minutes
11 ... 15 1 ... 5 4 minutes
16 ... 20 1 ... 5 Repetitive
Zone 2
NO âá
Zone 2
Cycles 3 âá
Alarm Cycles
‘Vibration’ or ‘Roller
Blind’ Zone Balance
Zone 2
ûûûû---- Part.
13572468
Assigning Partitions
Balance
Zone 2
Sensit. 2 âá
Sensitivity (Vibration
or Roller Blind)
6. Using 99
99
9or 00
00
0, select the Balance type,
thepress EE
EE
E.
NOTE: If you assign the ‘Vibration’ or ‘Roller Blind’ attribute to the
Zone, you must select one of the following Balance types:
!BAL - Balanced 1k5 (Balanced using 1.5 Kohm resistor)
!NC - Normally Closed
7. Using 99
99
9or 00
00
0, select the number of Alarm
Cycles: 0through 14.
If you want a continuous cycle, select ‘RP’
(Repetitive), then press EE
EE
Eto continue.
8. Using keys 11
11
1through 88
88
8(toggle keys), assign
the Zone to the Partitions:
û= the Zone assigned
-= the Zone is not assigned
Press EE
EE
Eto go the next step.
9. Using 99
99
9or 00
00
0, select the required Sensitivity
(1 through 20). This parameter is for
‘Vibration’ and ‘Roller Blind’ Zones only. If
you program this parameter for other Zone Types, it will have no effect.
To program the other parameters of Zones with the ‘Roller Blind’
attribute, refer to the various combinations shown in Table 3.
Example: for 3 PULSES and 4 MINUTES, you must set a value of 13.
10. For Zones with the ‘Vibration’ attribute —
using 99
99
9or 00
00
0, select the value of the Low
Shock Sensitivity or Cycles (0 through 7).
Press EE
EE
Eto confirm, and go back to step 2.
Zone 2
Cycles 7 âá
Zone 2
Cycles RP âá

12 Multifunction Control Panel
®®
PROGRAMMING
Outputs âá
Outputs
1. From the Installer Menu, using 99
99
9or 00
00
0, select
the Outputs option, then press EE
EE
E.
2. Using 99
99
9or 00
00
0, select the Output, then press EE
EE
E.
3. Using 99
99
9or 00
00
0, select the Signals option.
Press OO
OO
Oto Enable, or oo
oo
oto Disable the selected
Signal, as required. Press EE
EE
Eto go to continue.
Refer to the ‘Outputs Page’ section in the ‘INSTALLATION MANUAL’ for
the Signals list.
4. When all the Signals have been programmed, press EE
EE
Eto exit.
5. Using 99
99
9or 00
00
0, select the Attribute (NO or NC),
then press EE
EE
E.
6. Using keys 11
11
1through 88
88
8(toggle keys), assign
the Output to the Partitions.
û= the Output is assigned
-= the Output is not assigned
Press EE
EE
Eto confirm the programming, and go back to step 1.
In the example, Output 2 is Normally Closed (NC), and is assigned to Partitions
1 and 2.
Outputs
Output 2 âá
Output 2
Armed OFF âá
Output 2
ûû------ Part.
13572468
Output 2
NC âá

13
®®
Programming from the Keypad
Times
1. From the Installer Menu, using 99
99
9or 00
00
0, select
the Times option, then press EE
EE
E.
2. Using 99
99
9or 00
00
0, select the required option, then
press EE
EE
E.
If you select Patrol, Listen, Alarm or Superv., go to step 3a.
If you select Inactiv. or Neglig., go to step 3b.
If you select Partitions, go to step 3c.
NOTE - The Superv. Option is provided by KYO Series 32 Control panels
ONLY.
3a. Enter the selected Time, then press EE
EE
Eto confirm
and go back to step 2.
!The Patrol, Listen, Alarm times are in MINUTES
!The Supervisory Time is in steps of 15 minutes
(8 through 96: e.g. 8 = 120 minutes)
3b. Enter the Time, then press EE
EE
E.
!The Inactivity Time is in HOURS (0 through 99)
!The Negligence Time is in DAYS (0 through 99)
4b. Using toggle keys 11
11
1through 88
88
8, assign the
Inactiv. and/or Neglig. option to the Partitions.
û= the Option is assigned
-= the Option is not assigned
5b. Press EE
EE
Eto confirm and go back to step 2.
3c. Using 99
99
9or 00
00
0, select the Partition then press EE
EE
E.
4c. Using 99
99
9and 00
00
0, select Exit T., Entry T. or
Arm T., as required, then press EE
EE
E. To go back to
step 2., press ee
ee
e.
5c. Enter the Time, then press EE
EE
Eto confirm and and
go back to step 4c.
!The Exit Time and Entry Time are in SECONDS (0 through 99)
!The Auto-Arm Timeout is in MINUTES (0 through 99)
Times
Patrol âá
PROGRAMMING
Times âá
Partit.
Partition 01 âá
Programming the
Partition Times:
Exit T.
Entry T.
Arm T. Out
Partition 01
Exit T. âá
Patrol
30
Listen.
05
Alarm
10
Inactiv.
05
Neglig.
10
Inactiv.
ûû--ûû-- Part.
13572468
Neglig.
ûû--ûû-- Part.
13572468
Partition 01
30
Superv.
90
Programming times:
Inactiv.
Neglig.
Programming times:
Patrol
Listen.
Alarm
Superv.

14 Multifunction Control Panel
®®
PROGRAMMING
Inst.Cod âá
Installer Code
1. From the Installer Menu, using 99
99
9or 00
00
0, select
the Inst. Cod option, then press EE
EE
E.
2. Enter the New Installer Code (4 to 6 digits) then
press EE
EE
Eto confirm and go back to step 1.
NOTE: The New Installer Code will become operative after exiting the menu.
Inst.Cod
------
Keys
1. From the Installer Menu, using 99
99
9or 00
00
0, select
the Keys option, then press EE
EE
E.
2. Using 99
99
9or 00
00
0, select either the ‘Keys/Cards’ or
‘Wireless’ option, then press EE
EE
Eand follow the
relevant instructions.
NOTE - ‘Wireless’ option is available only on
Series 32 models.
!Key/Card option (if selected at step 2.)
3. To enroll a New Key or Card, select New key/card (Go to step 4a),
to Modify a Key or Card, select Modify (Go to step 4b),
to Delete a New Key or Card, select Delete (Go to step 4c)
then press EE
EE
E.
4a. Using 99
99
9or 00
00
0select the Reader where you
intend enrolling the Key/Card, then press EE
EE
E.
5a. Using 99
99
9or 00
00
0, select the Service or ClrCallQ
attribute. Enable (OO
OO
O) or disable (oo
oo
o) the
attribute, as required, then press EE
EE
E.
For further details, refer to the ‘Keys Page’
section in the INSTALLATION MANUAL.
6a. Using keys 11
11
1through 88
88
8(toggle keys), assign
the New Key/Card to the Partitions.
û= the Key/Card is assigned
-= the Key/Card is not assigned
7a. After assigning the Key/Card to the Partitions,
press EE
EE
E, the display will show the ‘PRO-
GRAMMING’ message (see right).
8a. Insert the Key into the ECLIPSE Reader (program-
med at step 4a.), or hold the Card near the sensitive
field of the PROXI Reader (programmed at step
4a.). Key/Card Enrollment will be confirmed by:
a) a long beep
b) by the acceptance message (see right) that indicates the identifier
New Key/Card
New key
Reader 01 âá
New key
Service ON âá
New key
ClrCallQ OFF âá
New key
PROGRAMMING
New key
û--ûû--û Part.
13572468
PROGRAMMING
Keys âá
New key 009
PROGRAMMING
Keys
Key/Card âá
Keys
Wireless âá

15
®®
Programming from the Keypad
Modify Key/Card
Delete Key/Card
number (e.g. 009)
c) by fast blinking on all 3 Reader LEDs
9a. Press ee
ee
e4 times to go back to step 3.
If the system does not Enroll the Key/Card (due to malfunction or because the system
has reached its limit of 128 keys) the Keypad will emit an audible error signal (Bop).
4b. Enter the Key/Card Identifier Number (e.g. 003)
or, using AA
AA
Aor BB
BB
B, select the required Key/Card
Identifier Number, then press EE
EE
E.
5b. Using 99
99
9or 00
00
0, select the Service or ClrCallQ
attribute. Enable (OO
OO
O) or Disable (oo
oo
o) the
attribute, as required, then press EE
EE
E.
For further details, refer to the ‘Keys Page’
chapter in the INSTALLATION MANUAL.
6b. Using keys 11
11
1through 88
88
8(toggle keys), assign
the Key/Card to the Partitions.
û= the Key/Card is assigned
-= the Key/Card is not assigned
7b. Press EE
EE
Eto confirm, and go back to step 4b.
4c. Enter the Key/Card Identifier Number (e.g. 005)
or, using AA
AA
Aor BB
BB
B, select the required Key/Card
Identifier Number, then press EE
EE
E.
5c. When the ‘Sure?’ message is shown (see right),
you can either press EE
EE
E, to confirm deletion and
go back to step 4c, or press ee
ee
e, to go back to step
4c, without deleting the Key/Card.
The keypad will emit an audible signal (long beep) to indicate that the
Key/Card has been deleted.
!Wireless option (if selected at step 2.)
3. Using 99
99
9or 00
00
0, select the Wireless key then
press EE
EE
E.
4. Enter the ESN then press EE
EE
E.
!Use OO
OO
Oor oo
oo
oto enter the letters.
!Use AA
AA
Aor BB
BB
Bto move along the row.
5. Using 99
99
9or 00
00
0, select either User Code 23 or
24 for the Wireless key then press EE
EE
Eto go
back to step 3.
Modify
Service ON âá
Modify
ClrCallQ OFF âá
Modify
û--ûû--û Part.
13572468
ßà Delete 005
Key/Card 5
Delete
Sure ?
ßà Modify 003
Key/Card 3
Wireless
1 000000 âá
Wireless
000000
Wireless
User Code 23 âá
Wireless Key

16 Multifunction Control Panel
®®
Codes
1. From the Installer Menu, using 99
99
9or 00
00
0, select
the Codes option, then press EE
EE
E.
2. Using 99
99
9or 00
00
0, select the Code Number (1
through 24), then press EE
EE
E.
3. Using 99
99
9or 00
00
0, select the Code Type (Inactive,
Main User, User, Duress, Patrol or DTMF),
then press EE
EE
E.
4. Using 99
99
9or 00
00
0, select the Arming Mode (Global,
A Mode and B Mode), then press EE
EE
E.
NOTE: If you select Global, go to step 5.
If you select A or B Mode, go to step 5a.
5. Using keys 11
11
1through 88
88
8(toggle keys), assign
the Code to the Partitions.
û= the Code is assigned
-= the Code is not assigned
6. Press EE
EE
Eto confirm and go back to step 4.
In the example, Code 5 is programmed as a User Code, enabled for Global
Arming on Partitions 1, 2 and 4.
5a. Using keys 11
11
1through 88
88
8, program the Arming
configuration for the Code, then press Eto
confirm and go back to step 2.
Each time you press the Partition number key
(1 through 8) the display will show a letter
(D, A, S, I or N) that represents an Arming option.
D= Disarm (the Control panel will monitor only the 24h zones of the
Partition)
A = Away Mode (the Control panel will monitor all the zones of the
Partition)
S= Stay Mode (the Control panel will not monitor the Partition zones
with the Stay attribute)
I= Instant (the Control panel will not monitor the Partition zones with the
Stay attribute, and will remove the Partition entry delay)
N= No Change (the Control panel will not change the Partition status).
NOTE: If no Partitions have been assigned to the User Code, this
programming field will be inactive (refer to step 5).
In the example, the A Mode Arming Configuration for User Code 5 is as
follows: Partition 1 = Disarm, Partition 2 = Away Mode, Partition 4 =
Instant (Stay Mode 0 Delay), Partitions 3, 5, 6, 7, 8 = No change.
Programming the
Arming configurations:
A and B Mode
PROGRAMMING
Codes âá
Codes
User Code 5 âá
User Code 5
User âá
User Code 5
Global âá
Global
xx-x---- Part.
13572468
User Code 5
A Mode âá
A Mode
DANINNNN Part.
13572468
Arming options:
D, A, S, I, N
Code Type:
Inactive
Main User
User
Duress
Patrol
DTMF

17
®®
Programming from the Keypad
PROGRAMMING
Readers âá
Readers
1. From the Installer Menu, using 99
99
9or 00
00
0, select
the Readers option, then press EE
EE
E.
2. Using 99
99
9or 00
00
0select the Reader (1 through 16),
then press EE
EE
E.
3. Using 99
99
9or 00
00
0Enable (ON) or Disable (OFF)
the Reader, then press EE
EE
E.
4. Using 99
99
9or 00
00
0, select Arming Mode (Global, A
Mode or B Mode), then press EE
EE
E.
NOTE: If you select Global, go to step 5.
If you select A Mode or B Mode, go to step 5a.
5. Using keys 11
11
1through 88
88
8(toggle keys), assign
the Reader to the Partitions.
û= the Reader is assigned
-= the Reader is not assigned
6. Press EE
EE
Eto confirm and go back to step 4.
In the example, Reader 05 is programmed to Arm the system in Global
Mode, and is assigned to Partitions 3 and 4.
5a. Using keys 11
11
1through 88
88
8, program the Arming
configuration, then press Eto confirm and go
back to step 2.
Each time you press the Partition number key
(1 through 8) the display will show a letter
(D, A, S, I or N) that represents the Arming option.
D= Disarm (the Control panel will monitor only the 24h zones of the
Partition)
A = Away Mode (the Control panel will monitor all the zones of the
Partition)
S= Stay Mode (the Control panel will not monitor the Partition zones
with the Stay attribute)
I= Instant (the Control panel will not monitor the Partition zones with the
Stay attribute, and will remove the Partition entry delay)
N= No Change (the Control panel will not change the Partition status).
NOTE: If no Partitions have been assigned to the Reader, this programming
field will be inactive (refer to step 5).
In the example, the B Mode Arming configuration for Reader 05 is as follows:
Partitions 1, 2, 5, 6, 7 and 8 = Not Enabled, Partition 3 = Away Mode,
Partition 4 = Disarm.
Readers
Reader 05 âá
Reader 05
ON âá
Reader 05
Global âá
Global
--ûû---- Part.
13572468
Reader 05
B Mode âá
B Mode
--AD---- Part.
13572468
Selecting the Reader
Enabling the Reader
Arming Mode:
Global, A or B Mode
Assigning the Reader
to Partitions
Arming option:
D, A, S, I, N
Programming the
Arming configurations:
A or B Mode

18 Multifunction Control Panel
®®
PROGRAMMING
Keypads âá
Keypads
1. From the Installer Menu, using 99
99
9or 00
00
0, select
the Keypads option, then press EE
EE
E.
2. Using 99
99
9or 00
00
0, select the required option
(‘Program’ or ‘Language’), then press EE
EE
Eand
work carefully through the relevant instructions.
!!
!!
!Program option
3a. Using 99
99
9or 00
00
0, select the Keypad (1 through 8),
then press EE
EE
E.
4a. Using 99
99
9or 00
00
0, select the Keypad Type (select
‘None’ for NO KEYPAD), then press EE
EE
E.
5a. Using keys 11
11
1through 88
88
8(toggle keys), assign
the Keypad to the Partitions.
û= the Keypad is assigned
-= the Keypad is not assigned
6a. Press EE
EE
Eto confirm and go back to step 3a.
In the example, Keypad 03 (LCD Keypad) is assigned to Partitions 1 and 5.
!!
!!
!Language option
3b. Press the key that corresponds to the required
language (in brackets e.g. <ENG>).
4b. Press EE
EE
Eor ee
ee
eto confirm. The selected language
will be operative immediately. The system will go back to step 2.
Keypads
Program
Keypads
Language
Program
Keypad 03 âá
Keypad 03
LCD Keyp. âá
Keypad 03
û---û---
13572468
1: ITA <2: ENG>
3: ESP 4: FRA
Select the Language
Select the Keypad
Only on Series è

19
®®
Programming from the Keypad
PROGRAMMING
Date/T. âá
Date/Time
1. From the Installer Menu, using 99
99
9or 00
00
0, select
the Date/T. option, then press EE
EE
E.
2. Using AA
AA
Aor BB
BB
B, select the Day, Month, Year,
Hour or Minutes field.
Use 99
99
9or 00
00
0change the values as required.
3. Press EE
EE
Eto confirm and go back to step 1.
GG
GG
GRemember to put the Clock forward or back an hour for the Summer Time
changeover.
Date/Time ßàáâ
01/11/2002 12:55
PROGRAMMING
Timers âá
Timers
1. From the Installer Menu, using 99
99
9or 00
00
0, select
the Timers option, then press EE
EE
E.
2. Using 99
99
9or 00
00
0, select the Partition, then press EE
EE
E.
3. Using 99
99
9or 00
00
0, select the Day. Using OO
OO
Oor oo
oo
o,
Enable or Disable the Partition (All Days are OFF
at Default), then press EE
EE
E.
4. Using AA
AA
Aor BB
BB
B, select the Hour or Minutes.
Using 99
99
9or 00
00
0, select the value (max 23:59), then
press EE
EE
Eto confirm and go to step 2.
In the example, Partition 2will Arm every Wednesday at 10:35.
NOTE: The ‘En/Dis. Auto-Arm’ must be enabled, otherwise, Auto-Arming
will have no effect.
Timers
Partition 02 âá
Partition 2
WED ON âá
Partition 2
WED 10:35

20 Multifunction Control Panel
®®
Number 3
Cont. ID âá
Number 3
_____ Customer
Telephone
1. From the Installer Menu, using 99
99
9or 00
00
0, select
the Teleph. option, then press EE
EE
E.
2. Using 99
99
9or 00
00
0, select the Telephone Number
Identifier (1 through 8), then press EE
EE
E.
3. Using 99
99
9or 00
00
0, select the Telephone Number
Type (Voice, Teleserv, None or Centr.ST), then
press EE
EE
E.
4. Using keys 11
11
1through 88
88
8(toggle keys), assign the
Telephone Number to the Partitions, then press EE
EE
E.
û= the Telephone Number is assigned
-= the Telephone Number is not assigned
NOTE - The Telephone Numbers must be assigned to the Partitions,
otherwise, the User will be unable to program Voice Telephone Numbers
(refer to the USER MANUAL).
5. Enter the corresponding Telephone number.
Use AA
AA
Aor BB
BB
B, to move along the Telephone
Number row.
Use OO
OO
Oand oo
oo
ofor the following punctuation marks and pauses (to be
entered in the space indicated by the cursor):
a) “,” — use the comma to insert 2 second dialling pauses;
b) “_” — use the dash to clear telephone number digits;
c) *and #.
6. When the Telephone number is complete, press EE
EE
Eto confirm and go back
to step 2.
If you select ‘Centr.St’ at step 3., you must work through the following steps.
7. Using 99
99
9or 00
00
0select the Protocol, then press
EE
EE
E.
8. Enter the Customer Code (minimum 4 digits for
all reporting formats except CESA, that requires
5 digits), then press EE
EE
E.
Use AA
AA
Aor BB
BB
Bto move along the row.
Use OO
OO
Oor oo
oo
oto enter letters A through F.
9 .Using 99
99
9or 00
00
0, select either the Listen. or 2-way
option. Using OO
OO
Oor oo
oo
o, Enable or Disable these
options, as required.
10. Press EE
EE
Eto confirm and go back to step 2.
Teleph.
Number 3 âá
PROGRAMMING
Teleph. âá
Number 3
Voice âá
Number 3
0731667890______
Type:
Voice
Teleserv
None
Centr.St Number 3
ûûûûûûûû Part.
13572468
Type: Centr.St
Number 3
Listen. OFF âá
Number 3
2-way ON âá