Bentel Security KYO-Unit Series User manual

KYO
Unit
MAIN UNIT
MANUAL
®
MADE
IN
ITALY

®®
BENTEL SECURITY srl reserves the right to modify the technical specifications of this product without prior notice.
KYO 4 M – KYO 8 M – KYO 32 M – KYO 4 P – KYO 8 P – KYO 32 P
KYO 8G P-SW1 – KYO 8G P-SW2 – KYO 32G P-SW1 – KYO 32G P-SW2
Hereby, Bentel Security, declares that the above mentioned Control Panels are in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
The complete R&TTE Declaration of Conformity for each Panel can be found at
www.bentelsecurity.com/dc.html.
These Control Panels comply with CEI 79-2 2aed. 1993.
Installation of these systems must be carried out strictly in accordance with the instructions
described in this manual, and in compliance with the local laws and bylaws in force.
The above mentioned Control panels have been designed and made
to the highest standards of quality and performance.
The manufacturer recommends that the installed system should be completely tested at least once a month.
BENTEL SECURITY Srl shall not assume the responsibility
for damage arising from improper application or use.
The above mentioned Control panels have no user-friendly components, therefore,
should be serviced by authorized personnel only.
IMPORTANT: The following information is for disassembled Control Panels ONLY.
Ensure that the Manual you are using corresponds to that requested on the “RELEASE
ISSUES” label (see below) inside the package. Upgrades of the required KYO Unit Soft-
ware Release are also suitable.
Manual Release
Firmware Release
Software Release
RELEASE ISSUES
OK32 1.00 EN
Installation Manual
User Manual
Keypad Prog. Man.
Main Unit Manual
Kyo Unit Software
1.1
1.1
1.1
1.1
5.10
If the Manual/KYO Unit Software release does not correspond, DO NOT attempt to as-
semble or install the Control Panel until you have the required release.
The Manual Release Number is shown at the bottom of the last page, between the Code
and Date, and indicated in the figure below.
ISTUCBLEUNKYO 190303 P70
1.1
Manual
Release
Number
DateCode

3
®®
TABLE OF CONTENTS
Section 1 - Introduction .................................................. 5
Certification Formalities .................................................................... 5
General Features ................................................................................ 5
About the System ............................................................................... 7
Control panel Versions ...................................................................... 7
Components and Accessories .......................................................... 8
Technical Specifications ................................................................... 9
Section 2 - Identification of Components .................... 10
KYO 4 M – KYO 8 M – KYO 32 M ...................................................... 10
KYO 4 P – KYO 8 P – KYO 32 P ........................................................ 11
KYO 8G P-SW1 – KYO 32G P-SW1 .................................................. 12
KYO 8G P-SW2 – KYO 32G P-SW2 .................................................. 13
Status LEDs (only for ‘G’ series PCBs) ........................................... 15
Section 3 - Mounting the Components ....................... 17
Introduction ....................................................................................... 17
Boxes and Accessories .................................................................. 17
Installing the Transformer and Mains Screw Terminal - Fused ... 18
Metal box ........................................................................... 18
Plastic box ........................................................................ 19
Mounting K4-K8-K32 PCBs .............................................................. 19
Installing ‘G’ series PCBs (K8G-K32G) ............................................ 20
Metal box ........................................................................... 20
Plastic box ........................................................................ 20
Installing the Switching Power Supply ........................................... 21
Installing BAQ15 Switching Power Supplies .................. 21
Installing BAQ35T12 Switching Power Supplies ............ 21
Earthing the PCB ............................................................................... 22
Marking Ticket .................................................................................. 22
Connecting the KST Thermal Probe ............................................... 22
Connecting the NC2/VOX Voice Board ............................................ 23
Metal box ........................................................................... 23
Plastic box ........................................................................ 24
PCB Identification Label ................................................................... 24

4Multifunction Control Panel
®®
Section 4 - Installing the Control Panel ....................... 25
Mounting the Control Panel ............................................................. 25
Opening and Closing the Control Panel .......................................... 26
Section 5 - Installing the NC2/VOX .............................. 28
General Features .............................................................................. 28
Additional VOX-REM Modules .......................................................... 28
Installing Additional VOX-REM Modules .......................... 28
Record / Play Messages .................................................................. 29
Selecting Messages ........................................................ 30
Recording Alarm Messages ............................................ 30
Playing Messages ............................................................ 30
Programming .................................................................................... 31
Activation .......................................................................................... 31

5
®®
Section 1 - Introduction
This Manual is designed for anyone using a Control panel from the KYO range.
Most of the features described in this Manual are included on all KYO Control
panels (refer to Table 1.1). However, some features are included on certain
models only, in such cases, the Control panel will be specified.
8 Programmable Input Zones (4 for KYO 4 M and KYO 4 P)
Expandable to 32 Input Zones via optional M-IN/6 Input Expanders (for
KYO 32 series Control panels)
1 Balanced 24h Tamper Zone
1 Programmable Alarm Output: 1A relay (3A on ‘G’ models)
Auxiliary Open-Collector Outputs (OC):
3 x 150 mA for KYO 4, KYO 8 and KYO 32 series
5 x 500 mA for KYO 8 G and KYO 32 G series
General Features
SECTION 1 - INTRODUCTION
Control Panel
Certification Formalities
The KYO-Unit series can be purchased as out-of-the-box Control pan-
els, or as separate package components. Bentel Security S.r.l declares
that KYO-Unit separate package components comply with the essen-
tial requirements and other relevant provisions of Directive R&TTE
1999/5/CE — only when they are assembled by a security professional,
and are used as part of one of the Control panels provided for in
Section 3, and indicated in Table 1.1. in this Manual. Bentel Secu-
rity S.r.l. declares that CE Certification is not applicable when KYO
separate package components are improperly assembled or used.
Table 1.1 - Version
Version
Component
PCB Box Transf. TRF Power Supply
BAQ15
Power Supply
BAQ35T12
KYO 4 M K4 BOX-M 
KYO 8 M K8 BOX-M 
KYO 32 M K32 BOX-M 
KYO 4 P K4 BOX-P 
KYO 8 P K8 BOX-P 
KYO 32 P K32 BOX-P 
KYO 8G P-SW1 K8G BOX-P 
KYO 32G P-SW1 K32G BOX-P 
KYO 8G P-SW2 K8G BOX-P 
KYO 32G P-SW2 K32G BOX-P 

6Multifunction Control Panel
®®
Expandable to 14 x 150 mA Outputs for KYO 32 series
Expandable to 16 x 150 mA Outputs for KYO 32 G series
Metal box (Model M) or Plastic Box (Model P)
Accepts Conventional Fire Detectors, and provides restoral facility
Supports up to 8 Keypads
Supports up to 16 Readers (ECLIPSE and/or PROXI)
Accepts up to 128 SAT Keys and/or PROXI-CARDs
Manages 4 independent Partitions (8 for KYO 32 and KYO 32 G)
3 Arming Modes (Global, A Mode and B Mode): A and B Mode can be
programmed as: Away, Stay or Stay with no Entry delay
Auto-Arming for each Partition on Daily or Weekly basis
24 Programmable Codes (4 to 6 digits)
Partition Bypass for Patrol purposes with automatic or manual Rearming
Can be programmed from LCD Keypads (MIA or OMNIA/TAST-R)
Can be programmed from a computer via RS232 link cable or via telephone
Power Supplies:
Integrated 1A linear Power Supply in KYO 4, KYO 8 and KYO 32
1.5A Switching Power Supply in KYO 8G P-SW1 and KYO 32G P-SW1
3A Switching Power Supply in KYO 8G P-SW2 and KYO 32G P-SW2
Touch-tone (MF) or Pulse dialling
Manages 8 Telephone numbers for Alarm and Central Station calls
Supports the following Reporting Formats:
ADEMCO / SILENT KNIGHT - Slow 10 baud - 3/1, 4/1, 4/2
ADEMCO / SILENT KNIGHT - Fast 14 baud - 3/1, 4/1, 4/2
FRANKLIN / SECOA / DCI-VERTEX - Fast 20 baud - 3/1, 4/1, 4/2
RADIONICS - 40 baud - 3/1, 4/1, 4/2
SCANTRONIC - 10 baud - 3/1, 4/1, 4/2
CONTACT ID
CESA
Accepts commands from touch-tone phones (Arm, Disarm, Turn ON/OFF
Main board Outputs; Remote Talk/Listen-in — requires optional NC2/
VOX Voice Board
Manages Voice Calls (requires optional NC2/VOX Voice Board)
Remote Telephone Access via Dialler or Answer Mode
Remote Talk/Listen-in (requires optional NC2/VOX Voice Board)
256 Event Logger (can be viewed on computer or LCD Keypad) on Series
32 Models. 128 Events on Series 4-8 Models.
3 function keys for immediate Alarm calls from Keypad
Programmable Test Call
Teleservice Management
Double Call
Line-sharing Management
Digital Dialler

7
®®
Section 1 - Introduction
The Control panel is made up of a Control Unit, Digital Communicator and
Modem. It can be controlled from remote Keypads and/or Digital Key/Card
Readers.
The Digital Communicator can call up to 8 Telephone numbers for Teleservice
and communication to Central Stations. You can program the system to report
events using any one of the supported formats.
The NC2/VOX Voice board (accessory item) will allow the Communicator to
send 8 Voice messages to up to 8 Telephone numbers. The NC2/VOX Voice
board also provides the Talk/Listen-in feature.
The B-MOD Modem and Management software will allow you to program,
control and Teleservice (provide remote maintenance) from a remote computer.
The B-MOD/Rx Modem and the WinBCS software will allow you to program,
control, Teleservice and Monitor the system from a remote computer.
All Events, Alarms and Troubles, complete with Customer and Event details will
be logged on the Event Logger.
The User can access the system over the phone, in order to:
Arm/Disarm the system
Turn ON/OFF Reserved Outputs
Activate Talk/Listen-in sessions (NC2/VOX required)
This Control panel can be programmed:
a) on-site, using a MIA or OMNIA/TAST-R Keypad (accessory item)
b) on-site, using an RS232 Computer link
c) from remote computer, using a modem and downloading software
About the System
The Control panel
The Digital Communi-
cator
Voice Messages using
NC2/VOX
Teleservice
Telemonitoring
Programming the
system
Table 1.2 - Functional differences between Models
Model Features
Partition Innput (Zone) O.C. Output
KYO 4 M KYO 4 P 4 4 3 x 150 mA
KYO 8 M KYO 8 P 4 8 3 x 150 mA
KYO 32 M KYO 32 P 88
Expandable to 32*
3 x 150 mA
Expandable to 14 **
KYO 8G P-SW1 KYO 8G P-SW2 4 8 5 x 500 mA
KYO 32G P-SW1 KYO 32G P-SW2 88
Expandable to 32*
5 x 500 mA
Expandable to 16 **
**The M-IN/6 Expander Module manages 6 Inputs
** The M-OUT/6 Expander Module manages 6 OC Outputs — 150 mA (6 x 150 mA)
Control panel Versions
Accessing the system
using a remote Touch-
tone Telephone

8Multifunction Control Panel
®®
Table 1.3 - Components and Accessory Items
Code Description
K4 - K8 - K32 PCB for KYO4, KYO8 and KYO32
K8G - K32G PCB for KYO8 G and KYO32G
BOX-M Metal box for M Models
BOX-P Plastic box for P Models
TRF 17 Vac - 1.5 A Power Transformer
BAQ 15 1.5 A Switching Power Supply for SW1 Models
BAQ 35 T12 3 A Switching Power Supply for SW2 Models
MIA-D LCD Keypad (can be used for programming)
MIA-S LCD Keypad (can be used for program ming)
OMNIA/TAST-R LCD Keypad (can be used for programming)
NC2/TAST LED keypad
ICON/KP LED keypad
ECLIPSE Flush Mount Contactless Key Reader
PROXI Proximity Reader
SAT Digital key for ECLIPSE and PROXI Readers
PROXI-CARD PROXI Card
NC2/VOX Voice Board
VOX-REM Talk/Listen-In Zone Expander Module (Microphone + Loudspeaker)
M-IN/6 6 Input Expander Module
M-OUT/6 6 Output Expander Module (150 mA)
KISUNIT Manual Kit
VECTOR/RX Wireless Receiver — manages 16 Wireless devices
(e.g. ARC10, AMD10, AMC10, AGB10, ASD10)
ARC10 Wireless Key for Vector/RX
AMD10 Wireless Pet Immune PIR for Vector/RX
AMC10 Wireless Magnetic Contact for Vector/RX
ASD10 Wireless Smoke Detector for Vector/RX
AGD10 Wireless Glassbreak Detector for Vector/RX
B-MOD Teleservice Mod em
B-MOD/RX Teleservice and Telemonitoring Modem
SECURITY SUITE Management Software
CVSER/9F9F Computer Serial Link
ADSER/9M25F Adapter for CVSER/9F9F link cable for 25 Pole Serial Ports (DB-25)
KST Thermal Probe (for GModels only)
OVC-Link Output Voltage Control wire (for GModels only)
ASNC Snatch Microswitch for MIA Keypads and Tamper for Plastic boxes
MINI-ASNC Snatch Microswitch for PROXI-REA DERs
MAXI-ASNC Tamper Microswitch for Metal boxes
Components and Accessories

9
®®
Section 1 - Introduction
Technical Specifications
Table 1.4 - Technical Specifications
Control Panels
Specifications
Values
KYO 4 M
KYO 8 M
KYO 32 M
KYO 4 P
KYO 8 P
KYO 32 P
KYO 8 G P-SW1
KYO 32 G P-SW1
KYO 8 G P-SW2
KYO 32 G P-SW2
Voltage 230V~50Hz ±10%
Maximum Current draw 0.2 A 0.21 A 0.5 A
Maximum Power 45 W 50 W 115 W
Power Supply Battery-charger 13.8 V_/ 1 A 13.8 V_/ 1.5 A 13.8 V_/ 3 A
Insulation Class I
Maximum Current available for
peripherals
(including the battery charge
current)
0.9 A 1.3 A 2.8 A
Battery Housing
(Brand and Type)
12V - 7Ah
YUASA NP7-12 FR or Equivalent with
UL94-V2 (or superior) Case Flame Class
Recognized MF Tones Minimum Level 200 mVpp (-23 dBV) for Kyo32 Series
Minimum Level 360 mVpp (-17 dBV) for Kyo4-8 Series
Operating Temperature +5 ÷ +40º C
Dimensions in mm (W x H x D) 235 x 269 x 77 309 x 227 x 89
Weight (without Battery) 2.7 Kg 1.8 Kg 1.2 Kg 1.3 Kg
Complies with
CEI Normative Laws
EN 60950:2000 - EN50081-1:1992
EN50130-4:1995+A1:1998 - CEI 79-2 2aed. 1993
COMPONENTS and ACCESSORY ITEMS
Description Max. Current Draw (mA) Dimensions (W x H x D) mm
Main Board KYO 4-8-32 100 122 x 118
KYO 8G-32G 150 166 x 109
Keypad
MIA-S / MIA-D 50 164 x 133 x 44
OMNIA/TAST-R 50 160 x 73 x 30
NC2/TAST 80 117 x 96 x 25
ICON/KP 80 160 x 73 x 30
Reader ECLIPSE 30 20 x 44 x 48
PROXI 30 78 x 108 x 22
Expander M-IN/6 (Input) 27 108 x 101 x 34
M-OUT/6 (Output) 11 108 x 101 x 34
NC2/VOX Voice Board 30 58 x 71
VectorRX Receiver 50 146 x 290 x 28
Table 1.4 shows the Technical Specifications of the various Control panels and
accessory items.

10 Multifunction Control Panel
®®
SECTION 2 - IDENTIFICATION OF COMPONENTS
The numbers in boldface in square brackets [ ], in this and other Manuals
relevant to this product, refer to the components described in this section.
Figure 2.1 - KYO 32 M Control panel complete with NC2/VOX Voice Board (accessory item)
19b
2
19a
17
LE LI
3332 34 35 36
56 789a
AC
30 31
COMNC 0201+B
19 20 2221 2423
GRN
25 26
REDBLKYEL
27 2928
03
4
14
11d
15
2
4
12a
2 2
11
9c
10
10
3a
3a
13c
13a
18
3a
3a
3a
19c
4
11b
11d 9d
KYO 4 M 

KYO 8 M 

KYO 32 M

11
®®
Section 2 - Identification of Components
N
L
L
N
51
96
9d
11
10 22546 783b 3b
9a
15
2
12a
3c
4
19b
2
11a
19a
4
9c
10
13a
11a
13b
18
17
3c
12b
12b
14
19c
Figure 2.2 - KYO 32 Control panel complete with NC2/VOX Voice Board (accessory item)
KYO 4 P 

KYO 8 P 

KYO 32 P

12 Multifunction Control Panel
®®
Figure 2.3 - KYO 32G P-SW1 Control panel with NC2/VOX Voice Board (accessory item)
KYO 8G P-SW1 

KYO 32G P-SW1
LN
1
1
22 5 4683b 3b
11c
15
2
12a
28
2
11a
9b
9c
20b
11a
18
3c
12b
729a
24
22b
19a
10
16
4
17
4
12b
10
3c
29b
24
13b
26
9d

13
®®
Section 2 - Identification of Components
Figure 2.4 - KYO 32G P-SW2 Control panel complete with NC2/VOX (accessory item)
KYO 8G P-SW2 

KYO 32G P-SW2
11
22 5 4683b 3b
11c
15
2
17
12a
4
27
2
11a
28
9b
25a
9c
20a
11a
18
3c
12b
12b
729a
25b
19a
23
22a
21
10
10
16
26
3d
4
3c
29b
24
13b
9d

14 Multifunction Control Panel
®®
Table 2.1 - Identification the Main Unit Parts
Part Description
1Frontplate Screws (2)
2Locations (4) for backplate screws (Ø = 5 mm)
3a Reverse locking PCB supports (see Figure 3.3)
3b PCB location Tabs
3c Locations (2) for PCB screws
3d Arrester for BAQ35T12 Switching Power-Supply/Battery Charger
4Terminal Board
5DB-9 male connector for computer link
6BPI Level Jumper: 12Vk5V 5 V (at default); 12Vj5V 12 V
7Firmware Release label
8Stop Alarm Jumper: o Alarms enabled (at default); O Alarms inhibited
Stop Alarm Jumper: o Alarms enabled (at default); O
9a Fuse — protects against battery polarity inversion (250V-8A )
9b Fuse — protects BPI Bus [+] terminal (250V-2A)
9c Fuse — protects Auxiliary Power Lines (250V-5A)
9d Reserved Jumper
10 Tamper Microswitch Connector (N.O. at default)
11a Tamper Microswitch for BOX-P (Accessory Item)
11b Tamper Microswitch for BOX-M (A ccessory Item)
11c On-Board Tamper Microswitch (Only for K8G and K32G PCBs)
11d Plastic spacers (2): inside the MAXI-ASNC Tamper Microswitch package
12a Optional Voice Board (Order Code: NC2/VOX — refer to Section 5)
12b Voice Board Holder
13a Earth Wire
13b Earth Wire on PCB - terminal (L=400 mm)
13c Earth Wire on PCB - terminal (L=120 mm)
14 Power Transformer — 220-17Vac-1.5A (Order Code: TRF)
15 Battery wires
16 Status LEDs (Refer to Table 2.3)
17 Cable entry
18 Marking Ticket
19a Mains Screw Terminal — for Mains and Earth connections
19b Fuse (250V-500mA) — inside the Mains Screw Terminal
19c Adhesive Label

15
®®
Section 2 - Identification of Components
Table 2.3 - KYO 8 G and KYO 24 G LEDs
LED Description
30
Mains (Green):This LED should be ON (Mains OK).
This LED will turn OFF to signal Mains Trouble (Blackout).
During Blackout, the system will be powered by the battery.
WARNING: Mains Trouble must be cleared before the battery runs Low.
31 Battery (Red) - this LED will turn ON to signal Low Battery or Trouble with the Battery
Charge Circuit.
32 BPI Fuse (Red) - this LED will turn ON to signal that the BPI Bus Fuse [9b] has blown.
33 Digital Communicator (Red) - this LED will turn ON to signal that the Digital
Communicator has engaged the Telephone line.
34 BPI Bus (Red) - this LED will turn ON to signal Communication Trouble between the
Control panel and the peripherals (Keypads, Readers, etc.).
Status LEDs (only for ‘G’ series PCBs)
Table 2.3 contains as description of the 5 Status LEDs on the K8G and K32G
PCBs (can be seen when the Control panel is open, see Figure 2.5).
Table 2.2 - Identification of the Switching Power Supply Components
Part Description
20a BAQ35T12 Switching Power Supply
20b BAQ15 Switching Power Supply
21 Mains LED (ON = Mains OK)
22a Fine Adjustment Trimmer
22b KST Jumper — this Jumper must be inserted, when a KST Thermal Probe is
connected to the battery
23 Auxiliary Terminals for system peripheral (Output = 13.8 Vcc)
24 Screw to secure the Switching Power Supply to the backplate:
1 x BAQ35T12 - 2 x BAQ15
25a Screw for the Switching Power Supply
25b Snap Rivet
26 Thermal probe — to be fitted to the battery (Order Code: KST)
27 Fuse — protects Switching Power Supply (250V-2A)
28 Fuse — protects against Battery polarity inversion (250V-6.3A )
29a Connector for the Switching Power Supply
29b OVC-Link wire (Output Voltage Control)

16 Multifunction Control Panel
®®
Figure 2.5 - KYO 8G and KYO 32G Status LEDs
30
31
32
33
34
Table 2.4 - Identification of the NC2/VOX Components
Part Description
35 LOC-MIC Jumper: K(at Default) - NC2/VOX Microphone Enabled
LOC-MIC Jumper: J- NC2/VOX Microphone Disabled
36 REM-MIC Jumper: J(at Default) - VOX-REM Remote Microphone Disabled
REM-MIC Jumper: K- VOX-REM Remote Microphone Enabled
37 Terminal board for VOX-REM Module
38 REM-SP Jumper: J(at Default) - VOX-REM Remote Speaker Disabled
REM-SP Jumper: K- VOX-REM Remote Speak Enabled
39 LOC-SP Jumper: K(at Default) - NC2/VOX Speaker Enabled
LOC-SP Jumper: J- NC2/VOX Loudspeaker Disabled
40 Flat Cable
41 Microphone
42 PLAY button
43 RECORD button
44 Status LEDs
Figure 2.6 - NC2/VOX Voice Board Components
41
42
43
44 35 36 37
38
40
39

17
®®
Section 3 - Mounting the Components
SECTION 3 - MOUNTING THE COMPONENTS
Introduction
Please read this section to get an overall view of the steps involved in installing
Control panels from the KYO Unit range.
71.75 mm
Fixed screws
M3x10 71.75 mm
Metal Box — BOX-M Plastic Box — BOX-P
Screw Location Ø 2.5mm
[19c]
[19a]
[19c]
[19a]
M3 Nut to secure
Mains Terminal Screw to secure
Terminal board
Figure 3.1 - Installing the Transformer and Mains Terminal board
Boxes and Accessories
Metal and Plastic boxes are available.
The Metal Box (Order Code BOX-M) package includes the following parts:
18 Balance Resistors — 10 Kohm
4 plastic PCB supports
1 x 12cm Earth wire (Yellow-Green) with eyelet [13c]
4 hexagonal nuts — M3
2 Parker screws — 2.9 x 7.5 to secure the Frontplate
Metal box

18 Multifunction Control Panel
®®
Plastic Box
The Transformer (see Figure 3.1) package includes the following parts:
1 Mains Screw Terminal - Fused [19a] — 500 mA
1 Adhesive Label [19c] for the Mains Screw Terminal
1 x 12 cm Earth wire (Yellow-Green) with eyelet [13a] for earthing the
Metal box or Transformer
To install the Transformer (Order Code TRF), work carefully through the fol-
lowing steps (refer to Figure 3.1).
Metal box
1.Stick the label [19c] onto the backplate, with one hole going over the fixed
screw, and the other in correspondence with the Mains Terminal [19a]
screw location.
2.Fit the Mains Screw Terminal [19a] onto the fixed screw (as indicated on
the label) then, using the hexagonal nut, secure it to the backplate.
The Plastic Box (Order Code BOX-P) package includes the following parts:
18 Balance Resistors — 10 Kohm
1 x 40 cm Earth wire (Yellow-Green) without eyelet [13b]
2 Parker screws — 2.9 x 7.5 to secure the PCB
1 Parker screw — 2.9 x 9.5 to secure the BAQ35T12 Switching Power Supply
2 Parker screws — 3.9 x 9.5 to secure the Frontplate
1 Parker screw — 3 x 14.2 to secure the Mains Screw Terminal
2 Parker screws — 3 x 8 to secure the Transformer or BAQ15 Switching
Power Supply
Installing the Transformer and Mains Screw Terminal - Fused
Figure 3.2 - Connecting the Earth wire [13a]
Metal Box — BOX-M Plastic Box — BOX-P
[13a]
[13a]
Screws
3 x 8
Hexagonal
nuts M3
b
a

19
®®
Section 3 - Mounting the Components
Please read this section to get an overall view of the steps involved in installing
K4,K8 and K32 PCBs in Metal and Plastic boxes.
Mounting K4-K8-K32 PCBs
3.Mount the Transformer onto the 2 fixed screws (M3x10) on the backplate
of the Metal box.
4.Fit the eyelet terminal [13a] to the fixed screw (as shown in Figure 3.2a) then,
using two hexagonal nuts, secure the transformer to the backplate.
5.Connect the Transformer primary (RED wires) to terminals [N] and [L].
6.Connect the free end of the Earth wire [13a] to the [QQ
QQ
Q] terminal on the
Mains Screw Terminal [19a] (as shown in Figure 3.2a).
Plastic box
1.Stick the label [19c] onto the backplate (as shown in Figure 3.1). Ensure that
the 2 label holes correspond to the 2 holes on the backplate.
2.Place the Mains Screw Terminal onto the screw location (Ø 2.5) then, using
the Parker screw (3 x 14.2) secure it to the backplate.
3.Using the 2 holes on the backplate as reference, mount the Transformer
[14] then attach the eyelet terminal [13a](as shown in Figure 3.2b).
4.Using the two 3 x 8 parker screws, secure the Transformer to the backplate.
5.Connect the Transformer primary (RED wires) to terminals [N] and [L].
6.Connect the free end of the Earth wire [13a] to the [QQ
QQ
Q] terminal on the
Mains Screw Terminal [19a] (as shown in Figure 3.2b).
51
96
Figure 3.3 - Fitting the Reverse Locking PCB Supports

20 Multifunction Control Panel
®®
Metal box
1.Insert the 4 reverse locking PCB supports [3a] into their locations on the
backplate, then attach the PCB. If you are installing an NC2/VOX Voice
Board, insert the supports (LEDs to the bottom) and then attach the
NC2/VOX Voice board (see Figure 3.3).
2.Using a hexagonal nut (M3), secure the Earth wire (Yellow-Green) eyelet
[13c] to the screw (M3x10) on the backplate (see Figure 2.1).
3.Connect the other end of the Earth wire (Yellow-Green) to terminal 36
(--
--
-) on the PCB.
4.Connect the Transformer secondary (YELLOW wires) to terminals 30-
31 (AC) on the PCB.
5.If you are fitting a Microswitch [11b], insert the two spacers [11d] then,
using the two hexagonal nuts, secure the Microswitch to its location (see
Figure 3.3). Connect the wire to the connector [10].
Plastic box
1.Slide the PCB under the 2 tabs [3b].
2.Using the 2 (2.9 x 7.5) Parker screws (in screw locations [3c]), secure the
PCB to the backplate.
3.Connect one end of the Earth wire (Yellow-Green) [13b] to the [--
--
-]
terminal (36) on the PCB, and the other to the [QQ
QQ
Q] terminal on the Mains
Screw Terminal [19a] together with the other Earth wire [13a].
4.Connect the Transformer secondary (YELLOW wires) to terminals 30-31
(AC) on the PCB.
5.If you are fitting a Microswitch [11a], insert it into the Microswitch holder
then connect the wire to one of the two connectors [10] on the PCB (see
Figure 2.2). The second connector [10] can be used for another
Microswitch on the outside of the cabinet (see Figure 2.2).
Installing ‘G’ series PCBs (K8G-K32G)
Please read the following instructions, to get an overall view of the steps involved
in installing K8G and K32G PCBs.
NOTE: ‘G’ series PCBs can be installed in plastic boxes only.
1.Slide the PCB under the 2 tabs [3b].
2.Using the 2 (2.9 x 7.5) Parker screws (in screw locations [3c]), secure the
PCB to the backplate.
3.If you are fitting a Microswitch [11a], insert it into the Microswitch holder
then connect the wire to one of the two connectors [10] on the PCB (see
Figure 2.3 or 2.4). The second connector [10] can be used for another
Microswitch on the outside of the cabinet.