Bentel Security FireClass 200 User manual

®
INSTALLATION MANUAL

Via Gabbiano, 22 - Z.I. S.Scolastica - 64013 CORROPOLI (TE) - ITALY
Installation manual: Analogue Fire Control Panel FireClass200
Istruzioni Inst. Inglese Antin. FC200/UK ISTINSFC200/UK
The following versions of the Fireclass200 series are available:
FC200 - Master panel with 4 A Linear power supply;
FC200/S - Master panel with 2.5 A Switching power supply;
FC200/SL - Slave panel without power supply unit;
f a technical feature is common to all versions, the name Fireclass200 is used in the description.
If a technical feature applies to a specific version, the name of the version concerned is specified.
Proper functioning of the FireClass200 components can be guaranteed ONLY when ambient
conditions, external to the cabinet, comply with the 3k5 category of IEC 721-3-3:1978.
The Loops of the FireClass200 control panel support 396 Analogue Devices.
The Conventional Zone of the FireClass200 control panel supports30 Conventional Devices.
The Fireclass200 supports a maximum of 512 devices in all.
In order to meet standards and qualify for IMQ Certification, the FC200/SL Slave panel must
be equipped with a BENTEL BA424 (27.6 V - 4 A) Linear power supply or
BENTEL BAQ60/24 (27.6 V - 2.5 A) Switching power supply.
Only the Manufacturer (Access Level no. 4 — refer to “Accss Levels” section) can install the
FC200/SL Slave panel power supply.
The FC200/SL Slave panel can operate ONLY when connected to a FireClass200 Master panel.
BENTEL SECURITY srl reserves the right to change the technical features of this product
without prior notice.
Fc100 - Master panel with 2.5 A Switching power supply;
I
FC200 - FC200/S - FC200/SL - FC100:
.
Hereby, Bentel Security,
declares the above mentioned Control Panels to be in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC
These Control Panels comply with
Installation of these systems must be carried out strictly in accordance with the instructions
described in this manual, and in compliance with the local laws and bylaws in force
The above mentioned Control panels have been designed and made to the highest
standards of quality and performance.
The manufacturer recommends that the installed system should be completely tested
at least once a month.
The complete R&TTE Declaration of Conformity for each Panel can be found
at www.bentelsecurity.com/dc.html.
.
.
BENTEL SECURITY Srl shall not assume the responsibility for damage arising from
improper application or use. The above mentioned Control panels have no user-friendly
components, therefore, should be serviced by authorized personnel only.
EN54-2EN54-4 1999;

TABLE OF CONTENTS
FC200 and FC100 . . . . . . . . . . . . . . . . . . . . 6
OVERVIEW 7
Access Levels . . . . . . . . . . . . . . . . . . . . . . 7
Main Features . . . . . . . . . . . . . . . . . . . . . . 7
Options with requirements . . . . . . . . . . . . . . . . 8
Telecom Module FC200/COM (Accessory item) . . . . . 8
Alarm cycle . . . . . . . . . . . . . . . . . . . . . . . . 8
Upgraded/New technical features (Firmware
version 4.00) . . . . . . . . . . . . . . . . . . . . . . 10
PARTS IDENTIFICATION 11
Main unit (FireClass200) . . . . . . . . . . . . . . . . . 11
Output Expander (FC200/6OUT) . . . . . . . . . . . . 18
Loop Interface . . . . . . . . . . . . . . . . . . . . . . 18
Telecom Module FC200/COM . . . . . . . . . . . . . . 19
Repeater . . . . . . . . . . . . . . . . . . . . . . . . . 20
INSTALLATION 21
Mounting the Control panel . . . . . . . . . . . . . . . 21
Installing Output expanders (FC200/6OUT) . . . . . . 22
Installing the Telecom Module (FC200/COM) . . . . . 22
Installing Repeater Panels (FC200/REP) . . . . . . . 22
Completing the Connections . . . . . . . . . . . . . . 23
Main board terminals . . . . . . . . . . . . . . . . . . 23
Connectiing Addressable Analogue Devices . . . . . 26
Connecting Conventional Devices . . . . . . . . . . . 28
Connecting Repeaters and Slave Panels . . . . . . . 29
Connecting Output Devices . . . . . . . . . . . . . . . 30
Bell Outputs . . . . . . . . . . . . . . . . . . . . . . . 30
Connecting the Telecom Module (FC200/COM) . . . . 31
Connecting the Power Supply . . . . . . . . . . . . . 32
Maintenance . . . . . . . . . . . . . . . . . . . . . . . 33
3

USING THE SYSTEM 35
Operating the system . . . . . . . . . . . . . . . . . . 35
Accessing the system . . . . . . . . . . . . . . . . . . 37
PROGRAMMING 39
Auto (Autolearning - Automatic enrolling) . . . . . . . 40
Connections: Loop 1 and Loop 2 . . . . . . . . . . . . 41
Connections: Network . . . . . . . . . . . . . . . . . 43
Programming: Fire detectors . . . . . . . . . . . . . . 44
Programming: Input modules . . . . . . . . . . . . . . 46
Programming: Output modules . . . . . . . . . . . . . 47
Programming: Conventional Zone module . . . . . . . 49
Programming: Repeaters and Slave panels . . . . . . 49
Devices . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Loop 1 and Loop 2 . . . . . . . . . . . . . . . . . . . 50
Conventional Line . . . . . . . . . . . . . . . . . . . . 51
Bell Outputs . . . . . . . . . . . . . . . . . . . . . . . 52
Network . . . . . . . . . . . . . . . . . . . . . . . . . 53
Password (PassWD) . . . . . . . . . . . . . . . . . . . 54
Welcome Message (MesINI) . . . . . . . . . . . . . . . 55
Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
OPTION . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Prealarm time (P) . . . . . . . . . . . . . . . . . . . . 58
Warning Threshold (W) . . . . . . . . . . . . . . . . . 58
Alarm Verify (V) . . . . . . . . . . . . . . . . . . . . . 59
Drift Compensation . . . . . . . . . . . . . . . . . . . 60
Timer and Special Timer (T and S) . . . . . . . . . . . 61
Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Pulse . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Extinction Mode . . . . . . . . . . . . . . . . . . . . . 64
System . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Date and Time . . . . . . . . . . . . . . . . . . . . . 66
Blink . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Wires . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Silence mode . . . . . . . . . . . . . . . . . . . . . . 68
Walk Test . . . . . . . . . . . . . . . . . . . . . . . . 69
Network . . . . . . . . . . . . . . . . . . . . . . . . . 70
4Analogue Fire Control Panel FireClass200

Printer . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Verify . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Factory . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Restore default . . . . . . . . . . . . . . . . . . . . . 72
Maintenance . . . . . . . . . . . . . . . . . . . . . . 72
Telephone . . . . . . . . . . . . . . . . . . . . . . . . 73
Dial. (Telephone Dialler) . . . . . . . . . . . . . . . . 74
Digital Telephone Communicator (Digital Commun.) . . 76
Telephone Numbers (T.Num) . . . . . . . . . . . . . 78
Options . . . . . . . . . . . . . . . . . . . . . . . . . 78
Remote management . . . . . . . . . . . . . . . . . . 80
MODIFYING 81
Disable . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Delete Verify . . . . . . . . . . . . . . . . . . . . . . . 84
Delete Log (Del. Log) . . . . . . . . . . . . . . . . . . 85
Telecom Module . . . . . . . . . . . . . . . . . . . . . 85
READING PARAMETER 87
Devices/Zones/Outputs . . . . . . . . . . . . . . . . . 87
Options . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Version . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Log data . . . . . . . . . . . . . . . . . . . . . . . . 90
Print . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Telecom Module . . . . . . . . . . . . . . . . . . . . . 92
QUICK GUIDE 95
General features . . . . . . . . . . . . . . . . . . . . . 95
Terminals . . . . . . . . . . . . . . . . . . . . . . . . . 96
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
5

FC200 and FC100 Features
FC200 FC100
EN54 Approved EN54 Approved
2 analogue loop: supports 99 sensors and 99
modules 1 analogue loop: supports 99 sensors and 99 modules
Automatic device-drift compensation Automatic device-drift compensation
Modular loop management
1 conventional input line: supports 30 fire de-
tectors and an unlimited number of Callpoints 1 conventional input line: supports 30 fire detectors and an unlimited number of
Callpoints
16 programmable software zones 16 programmable software zones
16 alarm repeat outputs (open-collectors): 1
per zone 16 alarm repeat outputs (open-collectors): 1 per zone
1 "C" alarm output 1 "C" alarm output
4 programmable, supervised, silenceable
alarm output (relays) ---- expandable to 16 us-
ing FC-200/6OUT expander modules
1 programmable, supervised, silenceable
alarm output (relay)
1 NON-supervised, NON-silenceable ancillary
alarm output (relay)
1 NON-supervised, NON-silenceable Fault out-
put (relay)
RS485 Interface ---- supports 8 repeaters RS485 Interface ---- supports 8 repeaters
RS232 Interface for serial printer ---- linked to
the Control panel or a PC for upload/download
operations
RS232 Interface for serial printer ---- linked to
the Control panel or a PC for upload/download
operations
200 event log 200 event log
Supports 2 FC200/6OUT output expanders to
provide 16 outputs Supports 2 FC200/6OUT output expanders to provide 13 outputs
Local/Remote Upload/Down load from PC Local/Remote Upload/Down load from PC
TELECOM Module (Accessory item) TELECOM Module (Accessory item)
Power supply: 230 Vca +/- 10% Power supply: 230 Vca +/- 10%
Available with 2.5 A power supply/battery charger
and with 27.6V-4A linear power supply Available with 2.5 A power supply/battery charger
Housing for 2 x 17 Ah batteries Housing for 2 x 17 Ah batteries
Dimensions (w x h x d): 432 x 577 x 131 mm Dimensions (w x h x d): 432 x 577 x 131 mm
Weight (without batteries): max. 9.0 Kg Weight (without batteries): max. 9.0 Kg
FC200 and FC100
The Installer and Operator manuals can be used with FC200 and FC100
Fire Control panels, however, where features and capacity differ, refer to
the above table.
6Analogue Fire Control Panel FireClass200

OVERVIEW
Access Levels
The FireClass200 Access Levels filter system control as follows.
Level 1 All persons can view the system status through the Plexiglas window.
Level 2A Only authorized key holders can open the cabinet door access the manual
commands (RESET, SILENCE and LOGGER).
Level 2B Only authorized User PINs (1 to 5 digit codes) can Enable/Disable the
Loop devices, Bell Outputs, Software Zones and Network devices.
Level 3A Only the Installer PIN (1 to 5 digit code) can access the parameter pro-
gramming phase.
Level 3B 0nly authorized personnel are allowed to open the cabinet (remove the screws
and open the control panel door) for maintenance work (change the battery,
replace fuses, etc).
Level 4 Only the manufacturer is allowed to open the cabinet (remove the screws
and open the control panel door) for PCB repair work (replace compo-
nents, etc.).
Main Features
Day/Night The FireClass200 can operate in Day or Night Mode.
If the system is silenced during Day Mode, SILENCE status will be held
until the system is unsilenced (i.e. unless new alarms or faults occur).
If the system is silenced during DAY Mode, SILENCE status will be held
until the system is unsilenced (i.e. unless new alarms or faults occur).Si-
lence will be enabled until the SILENCE button is pressed again.
If the system is silenced during NIGHT Mode, SILENCE status will be for
the preset time (accepted values: 30 seconds to 30 minutes).
This system provides Automatic Alarm Threshold variation.
The preset Alarm Threshold of analogue detectors will be increased during
Day Mode, in order to avoid false alarms caused by persons (cigarette
smoke, etc.) in the protected ambient.
OVERVIEW 7

Options with requirements
The FireClass200 control panel provides the following options with require-
ments (complies with European norm EN54 part 2):
Øoutputs to fire alarm routing equipment
Øco-incidence detection
Øfault signals from points
Ødisablement of addressable points
ØTest condition
Telecom Module FC200/COM (Accessory item)
The Telecom Module sends recorded messages to programmed telephone
numbers and, using reporting protocols, transmits data to central stations.
This module allows operators to manage the system over-the-phone by
means of the FC200/SW software package.
Description
r8 independent channels
rRecords one 11 second alarm message per channel
r32 programmable telephone numbers
rAccepts 15 digit telephone numbers and 1 or 5 second pauses
rRepeats alarm messages for up to 20, 40, 60 or 80 seconds
rRepeats call cycle up to 5 times
rVoice answer detection
rBypassable "dial tone" test
rTelephone-line Interface
rProtected against over-voltage
rDTMF and Pulse dialling
rDigital recording/Message playback
rNon-volatile memory
rManages the following reporting protocols:
ADEMCO SLOW 10 BAUD, ADEMCO FAST 14 BAUD, FRANKLIN 20
BAUD, RADIONICS 40 BAUD, SCANTRONIC 10 BAUD, CONTACT ID
(DTMF), SIA 300 BAUD.
Alarm cycle
If an alarm channel triggers an alarm, the telephone dialler will generate
the respective alarm cycle (as per figure 1).
8Analogue Fire Control Panel FireClass200

Phase 1 The dialler will switch to the telephone line.
Phase 2 The dialler will wait 3 seconds then will engage the telephone line.
Phase 3 If the Dial-tone check option is enabled (refer to the "Programming" sec-
tion), the dialler will wait for the dial tone.
NOTE: If the dialler does not detect the dialling tone within the preset
time, it will repeat the process 4 times before hooking-up and stepping
back to phase 1.
If this option is disabled the dialler will go directly to the next phase.
Phase 4 The dialler will dial the telephone number associated the with the alarm
channel concerned.
Phase 5 If the Voice answer detection option is enabled (refer to the "Programming"
section), the dialler will wait 25 seconds for a voice answer and, if detected,
will step to the next phase. If the Voice answer detection option 6is disabled,
the dialler will pause for several seconds before going to the next phase.
Phase 6 The dialler will send the respective alarm channel message. The message
will be played for the preset Message playback time (20, 40, 60 or 80
seconds).
Call cycle The Call cycle (set up during the programming phase) determines the
number of times each telephone number ---- assigned to the alarm channel
concerned ---- will be dialled (1 to 5 times).
Figure 1 Telecom Module alarm cycle
OVERVIEW 9

Upgraded/New technical features (Firmware version 4.00)
rExtended template provides full alarm details (refer to the Operator’s Man-
ual ---- pages 9, 10)
rRS485 protocol upgrade for fast data transmission
rCentralized Master panel Log ---- retrieves, saves and broadcasts all the
network events (refer to the Operator’s Manual pages 9, 10)- Logger on
Slave: (refer to the Software Manual "System")
rView Alarm event details from Repeaters (refer to the Operator’s Manual
---- pages 9, 10)
rNew "Ignore output supervision" option for dry-contact management of
Output Modules (refer to Installation Manual page 48)
rNew Single Zone/ALL Zone Double knock option (refer to the Installer’s
Manual ---- pages 48, 49)
rNew Zone Prealarm event (refer to the Installer’s Manual ---- pages 47, 48,
49)
rResets slave panel from master (refer to the Software Manual "System")
rResets master panel from slave (refer to the Software Manual "System")
rSets to Day Mode on power up (at default)
rVerify Alarm option (refer to the Installer’s Manual ---- page 44, 45 and Op-
erator’s Manual ---- pages 18, 25).
rManages Prealarms (refer to the Installer’s Manual ---- page 58 and Opera-
tor’s Manual ---- pages 9, 13).
rManages Warning signals (refer to the Installer’s Manual ---- pages 47, 48,
53, 59, 75)
+FireClass control panel firmware verions 4.00 and Repeater firmware ver-
sions 1.2 CANNOT operate on applications using FireClass control panels
and Repeaters with lower firmware versions.
10 Analogue Fire Control Panel FireClass200