Bentel Security KYO 320 User manual

®
USER MANUAL
EXPANDABLE MULTIFUNCTION CONTROL PANEL
KKYO 320
ISO 14001
9191.BNT2 ISO 14001 IT-52588
ISO 9001
9105.BNT1 ISO 9001 IT-52587 OHSAS 18001
9192.BSEC OHSAS 18001 IT - 60983

BENTEL SECURITY srl. reserves the right to change the technical specifications of this product without prior notice.
This system can be programmed using the respective (KYO320) Software Application 5.4.3 or higher.
Installation of the system must be carried out strictly in accordance with the instructions described in this manual, and in
compliance with the local laws and bylaws in force.
The KYO320 Control panels have been designed and manufactured to the highest standards of quality and performance.
The KYO320 Control panels have no user-friendly components, therefore, should be serviced by authorized personnel only.
BENTEL SECURITY shall not assume the responsibility for damage arising from improper application or use.
The manufacturer recommends that the installed system should be completely tested at least once a month.
Hereby, Bentel Security, declares that KYO320 Control panels comply with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Recycling information
BENTEL SECURITY recommends that customers dispose of their used equipments (panels, detectors, sirens, and other devices) in an environ-
mentally sound manner. Potential methods include reuse of parts or whole products and recycling of products, components, and/or materials.
For specific information see: www.bentelsecurity.com/en/environment.htm
Waste Electrical and Electronic Equipment (WEEE) Directive
In the European Union, this label indicates that this product should NOT be disposed of with household waste. It should be deposited at an ap-
propriate facility to enable recovery and recycling.
For specific information see: www.bentelsecurity.com/en/environment.htm
NOTE:
In addition to the present User Manual, the Installation and Programming from keypad Manual are also available for KYO320 control panel. It is pos-
sible to buy these manuals separately from the KYO320 control panel, or to download them from Bentel Security website: http://www.bentelsecu-
rity.com.
The control keypads of KYO320 control panel are the CLASSIKA and PREMIUM LCD keypads. All previous Bentel LCD keypads (Alison-S, Ali-
son-DVP, Mia-S, Mia-D) and the LED keypad Alison32LP continue to be supported by the KYO320 Control panel. For a correct functionality of
PREMIUM and CLASSIKA LCD keypad, the KYO 320 control panel must have a firmware rev. 2.06 or higher.

TABLE of CONTENTS
OPERATING YOUR SYSTEM FROM A
KEYPAD 5
Buzzer Volume 5
Contrast Adjustment 5
Brightness adjustment 6
Superkey functions 6
Audible and Visual signals on the Keypad 6
LEDs 6
Display 6
Basic Commands 8
Arming Partitions
(<Code> ON) 9
Disarming Partitions
(<Code> OFF) 9
Arming in A, B, C or D Mode
(<Code> A, B, C or D) 9
Quick Arming for PREMIUM LCD and CLASSIKA
LCD keypad 9
About Partition Arming 9
Quick View Trouble Mode (ENTER) 10
Partition status enquiry 10
Accessing the User menu (<CodeENTER)10
Reset Alarms and Tamper 11
Stop Alarms 11
Arm/Disarm 11
Zone status 11
Event Log 12
Enable/Disable Auto-arm 13
Teleservice request 13
Enable/Disable Teleservice 13
Enable/Disable Answering device 13
Activating Outputs (Turning ON/OFF Appliances) 13
Clear call queue 13
Overtime request 14
Change Time and Date 14
Change Telephone numbers 14
Reset PC programming 14
Programming PIN codes 14
Memo 15
Disable buzzer 16
Test Siren 16
Test Keypad 16
Continuous recording 16
Enable/Disable Timers 16
Enable/Disable Key 17
USING DIGITAL KEYS AND CARDS 19
Readers 19
Digital Keys/Cards 19
The Reader LEDs 20
No Key/Card at Reader 20
Key/Card at Reader 20
Multiple Systems 20
Digital Key/Card operations 21
Disarm (Turning OFF your system) 21
Arm — Global Mode (Turning ON your system) 21
Arm — A Mode 21
Arm — B Mode 21
Stop Alarms (for ECLIPSE Readers ONLY) 22
Arm/Disarm Patrol 22
The Wireless Key 22
Global Mode 22
Stay Mode 22
Disarm 22
Other functions 22
Low Battery 22
OPERATING THE SYSTEM FROM A
TELEPHONE 23
Remote Access via ‘Dialler’ mode 23
Remote Access via ‘Answer’ mode 23
Teleservice Enabled 23
Teleservice Disabled 23
Typing-in your User Code PIN 23
Entering Commands 23
Default PINs (Factory default) 25
KYO320 3

4KYO320

OPERATING YOUR SYSTEM FROM A KEYPAD
Read this section thoroSe si regola il volume a zero, il
buzzer emetterà comunque dei suoni ad un volume mi-
nimo DURANTE LA FASE DI REGOLAZIONE.
ughly to get an overall view of how to operate your
system from a Keypad. KYO 320 can manage 32
PREMIUM LCD and/or CLASSIKA LCD Keypads
(Fig.1) and 16 Alison/32LP.
ØPREMIUM LCD has a larger display with 2 lines and
16 columns and has a built-in Proximity Reader.
Premium LCD keypad provides 3 fast keys for instant
activation of Burglar, Fire and Emergency Alarms (to
be programmed by your Installer);
ØCLASSIKA LCD has a larger display with 2 lines and
16 columns but on the contrary of PREMIUM keypad
has NOT a built-in Proximity Reader.
CLASSIKA LCD keypad provides 3 fast keys for in-
stant activation of Burglar, Fire and Emergency
Alarms (to be programmed by your Installer)
Figure 1 shows the main compo
nents of the PREMIUM
LCD and CLASSIKA Keypads:
1 Function LEDs
2Display
3 Keys
4 Down flip
5Information chart
6Sensitive field
7 Fast Keys
Buzzer Volume
To adjust the volume of the internal buzzer, follow the
procedure described below:
1) Press and keep pressed the ESC key; the internal buz-
zer will start sounding a series of beeps in such manner
that the operator could hear the sound level in real time.
2a) To increase the volume, press key A for a number of ti-
mes and/or keep it pressed until the desired level is obtained:
2b) To lower the volume, press più volte and/or keep
pressed key Buntil the desired level is obtained.
3) To confirm the chosen level, press the ENTER key
(or wait a few seconds for the keypad to return to the
inactive state).
+NOTE – The buzzer will still emit a series of sound
alerts at extremely low volume, even if it has been
set to zero.
Contrast Adjustment
To adjust the contrast of the LCD display, press and
hold:
ØCto increase contrast
ØDto decrease contrast
To confirm the selected levels, press ENTER (or simply
wait a few seconds to enable the keypad back into the
stand by status) (see the PREMIUM keypad manual for
further information).
KYO320 OPERATING YOUR SYSTEM FROM A KEYPAD 5
1
4
5
2
3
21
36
7
a) b)
7
Figure 1 - a) PREMIUM LCD Keypad, b)CLASSIKA LCD Keypad.

Brightness adjustment
The brightness can set in a normal way or in the stand
by status (the keypad enables the stand by status
brightness after 10 seconds of inactivity).
To adjust the brightness of the LCD display, press and
hold:
ØAto increase brightness
ØBto decrease brightness
Press OFF to set the stand by brightness.
ON and OFF alternate, respectively, the settings for the
normal and the stand by status level.
To confirm the selected levels, press ENTER (or simply
wait a few seconds to enable the keypad back into the
stand by status).
+If the brightness in the "stand-by status" is set to a mi-
nimum, the keypad LEDs go out except in an alarm or
fault condition (see Manual of keypads).
Superkey functions
If your Installer has set up the ‘Superkeys’, you will be
able to perform some “Quick” operations from the key-
pad without using codes. The table shows how to acti-
vate the programmed functions.
PREMIUM LCD
CLASSIKA LCD Activation method
1Press and hold the key for
approximately 3 seconds
2Press and hold the key for
approximately 3 seconds
3Press and hold the key for
approximately 3 seconds
The ‘Superkeys’ can be set up to activate:
Ø Electrical appliances (e.g. Heating system, Lights,
etc.)
Øthe Digital communicator
Øthe Dialler
The ‘Superkey’ actions are instant and will be confir-
med by a feed back signal (beep).
The Superkeys can be set up to work differently on dif-
ferent Keypads.
Audible and Visual signals on the Keypad
Table 1 shows the meaning of the indicator LEDs on the
PREMIUM LCD and CLASSIKA LCD Keypads.
+Some of the display screens differ, depending on
whether the keypad has been set with the option
“Compatibility with EN50131” or not.
nLEDs
Refer to Table 1 for the description of the four LEDs on
the Keypad.
nDisplay
During standby status, the first line will show the Time
and Date, as follows.
17:05 26/08/06
AAADDDDD x ** ÿ
1 2 3 4 5 6 7 8 STbfstri
If the keypad has been set in EN50131 mode, the
standby display screen will be similar to the one show
below:
17:05 26/08/06
Enter PIN
+The text “Enter PIN” can be programmed by the in-
staller.
6KYO320
M
G
a
I
TABLE 1 - KEYPAD LEDs
Symbol Meaning
Off: all the keypad Partitions are Disarmed
On: at least one of the keypad Partitions is Armed
Slow blinking: STOP ALARMS function is Active
Fast blinking: STOP ALARMS function is Active and AT LEAST ONE of the keypad
Partition is Armed.
NOTE - With EN50131 keypad, the indicator light is always off: to display the various
functions listed above, you will have to enter the “View zone status” mode.
Off: Standby status -NO alarms-
On: Zone Alarms in memory
Slow blinking: Tamper on at least one zone or on thr Control panel
Fast blinking: Alarm and Tamper on at least one zone, or Tamper on the Control panel
Off: No trouble conditions detected
On: At least one Trouble condition detected
Slow blinking: At least one zone in Test status
Fast blinking: At least one zone in Test status and one in Trouble status
Off: No voice messages in memory
On: At least one voice message in memory
Note: The zone Alarm and Tamper events, signalled on the LEDs, refer to zones which belong to the
keypad Partitions.

If the Control panel has stored a zone Alarm or Tamper
event (aLED on or blinking, respectively), the first line will
show the description of the zone concerned, as follows.
Zone 005
AAADDDDD x ** ÿ
1 2 3 4 5 6 7 8 STbfstri
If the Control panel has stored several zone Alarms
and/or Tamper events in the memory, the first line will
show the zones concerned (one-by-one at 3 second in-
tervals). The second line will provide information on the
status of the Partitions. The left-hand side of the display
will provide information on the status of the Keypad Par-
titions, as shown in Table 3.
+KYO 320 manages 32 Partitions. However, only 8
Partitions can be viewed on PREMIUM LCD and
CLASSIKA LCD Keypads. Therefore, the numbers
below the display will correspond only when the
first 8 Partitions are selected (refer to Quick View
Partition mode).
Trouble conditions will be signalled on the right-hand
side of the second line. The trouble conditions are re-
presented by the Icons directly below the display. Me-
mory of Trouble conditions will be indicated by an “û“
above the respective Icon (refer to Table 4 for details).
If the Teleservice or Answering Machine facility is Ena-
bled, an asterisk (*) will be shown above the respective
Icon (refer to Table 5 for details).
If the Telepho
ne line is busy or down, a ÿwill appear
above the Icon (refer to Table 4 for details).
nBuzzer
The Keypad sounder will emit a beep each time you
press a key. It will also signal:
Øthe Exit time (slow beeps);
Øthe Entry time (fast beeps);
Øthe Auto-arm timeout (four-beep sequence);
Øif the respective option is enabled, Partition Alarm or
Tamper event in memory (two-beep sequence);
Ødata input errors or invalid operations (buzz).
KYO320 OPERATING YOUR SYSTEM FROM A KEYPAD 7
TABLE 2 - ARMING/DISARMING PARTITIONS (LCD KEYPADS)
Initial Mode Result
AAway The system will turn ON the perimeter and interior zones of the respective Partition
SStay The system will turn ON the perimeter zones of the respective Partition and will leave
the interior zones OFF.
IStay0Delay The system will turn ON the perimeter zones of the respective Partition and will leave
the interior zones OFF, and will remove the ENTRY TIME from zones which have one.
DDisarm The system will turn OFF the perimeter and interior zones of the respective Partition.
-
Disabled The respectivePartition is not a Keypad Partition, therefore, cannot be controlled from
the keypad.
Note: If the Partition has one or more Alarms in memory the letter will blink.
TABLE3-TROUBLESIGNALS (LCDKEYPADS)
Icon Signalled by Meaning
SûON - Control panel Tamper (Control panel open or dislodged)
Blinking - Control panel Tamper has cleared but at least one Open Panel event in memory
TûON - System Tamper
Blinking - System Tamper has cleared but there is at least one System Tamper event in
memory
bûON - Tamper on at least one peripheral device (Keypad, Reader, Expander or Receiver)
Blinking - Peripheral Tamper has cleared but there is at least one Peripheral Tamper event in
memory
fûON - A False Key/Card is present at a Reader
Blinking - At least one False Key/Card event in memory
sûON - A peripheral device (Keypad, Reader, Wireless or Expander) has been disconnected
Blinking - At least one Peripheral Trouble event in memory
NOTE: To clear the S,T,band fTrouble signals, select the Reset Alarm option from the User Menu.
TABLE 4 - TELEPHONE SIGNALS (LCD KEYPADS)
Icon Signalled by Meaning
t*OFF - Teleservice Disabled
ON -Teleservice Enabled
r*OFF - Answerphone facility Disabled
ON- Answerphone Facility Disabled
iÿOFF -LineFree
ON -LineBusy
Blinking -LineDown
A
S
-
D
I
x
x
x
x
x
S
T
b
f
s
STb
f
r
t
iÿ

Basic Commands
You can control eight basic commands from standby
status by typing-in your code and pressing the respecti-
ve keys (refer to the following Table). Access to ALL
commands — except ‘View Trouble’ — require entry a
valid User Code PIN.
Keypad set normally
Enter COMMAND
<Code> ON Arm
<Code> OFF Disarm
<Code> AA Mode Arm
<Code> BB Mode Arm
<Code> CC Mode Arm
<Code> DD Mode Arm
<Code> ENTER Access User Menu
ONLY ENTER "View trouble" mode
ONLY ESC List "By-passed zones"/"By-
passed zone"
Keypad set as EN50131
Key sequence (from
standby status) COMMAND
<Code> ON Arm
<Code> OFF Disarm
<Code> AA Mode Arm
<Code> BB Mode Arm
<Code> CC Mode Arm
<Code> DD Mode Arm
<Code> ENTER
View Area status if there are no
malfunctions, otherwise View
malfunctions.
From the View area status or
malfunctions screen, press
ENTER again to access the
User menu.
+‘View Trouble’ mode is available on LCD Keypads
at all times, and can be accessed without entering
a Code.
+Commands will affect only the Partitions common
to both the User code and Keypad concerned
(common Partitions).
Invalid commands will be signalled by a buzz and the
following message:
17:05 26/08/2005
Invalid code!
invalid commands may be due to the User code or the
Keypad (e.g. the User code is Disabled on the Keypad
Partitions).
8KYO320
TABLE 5 - "VIEW TROUBLE" MODE
Message Description
Tr oub. _pow. syst . The Control panel battery or at least one Power Station is not functioning properly
Low_battery The Control panel battery or at least one Power Station battery is low
AC_Ma i n s _failure The Mains power to the Control panel or to at least one Power station has failed
Bat t . _di sc. pw. s. At least one Power Station has disconnected its Battery
Faul t _chr g. pw. s. At least one Power Station has Battery-charger trouble
Swt ch. di sc. pw. s. At least one Power Station has disconnected its Battery-charger
Ou t _shor t __pw. s. At least one Power Station has one Output in short-circuit
Tel . _line_t r oub. Line down
Fus e_B1 Shortcuts/blown fuse on terminals +N1 and +A1 (1.85A-250V)
Fus e_B2 Shortcuts/blown fuse on terminals +N2 and +A2 (1.85A-250V) KYO320 only
Fus e_B3 Shortcuts/blown fuse on terminals +N3 and +A3 (1.85A-250V) KYO320 only
Fus e_B4 Shortcuts/blown fuse on terminals +B4 (1.85A-250V) KYO320 only
Fus e_B5 Shortcuts/blown fuse on terminals +B5 (1.85A-250V) KYO320 only
Fus e_+F Shortcuts/blown fuse on the power line +F (1.85A-250V)
Fus e_BPI _1Shortcuts/blown fuse on BPI line1 (1.85A-250V)
Fus e_BPI _2Shortcuts/blown fuse on BPI line2 (1.85A-250V)
Fus e_KEYBUS Shortcuts/blown fuse on the Key Bus (500 mA-250V)
St op_al . j ump. i n STOP ALARM jumper is connected
Low_battery_WLS Low Battery on one or more Wireless devices
War n. l i t hi umbat t The RAM battery must be replaced
Call Installer Service is due — Call your Installer
Cal l Cent r . St at . Central Station intervention is due — Call your Central Station
Daylight Saving The Control panel Clock has been turned forward/back
WLS Devi ce l ost Connection problems with a Wireless device (Missing or Trouble present)
Cl ock St opped The Control panel Clock has stopped
Vox _boar d_lost Connection problems with the Vox Board (Missing or Trouble)
St a r t _pr ogr am. Programming session via PC (on-site or via Modem) started during Disarmed status
Inactivity The zone"Inactivity Time" has expired
Di scl osed PI N A PIN (DUPLICATED at random) has been DISCLOSED to another User

+If you do not press a key within 30 seconds, the
keypad will revert automatically to standby status.
The User can enter the following commands at the
Keypad.
nArming Partitions (<Code> ON)
This command will Arm all the common Partitions of the
User code and the Keypad concerned.
+DO NOT assign Duress Codes to Arming com-
mands.
nDisarming Partitions (<Code>OFF)
This command will Disarm all the common Partitions of
the User code and the Keypad concerned.
Disarm under Duress
This command requires entry of a Duress Code. The
Control panel will Disarm the Partitions and will send
the programmed Alarm calls but will not signal the out-
going calls on the Keypad (usually signalled by a ÿover
the iicon).
Disarm by Patrol Code
If a Patrol Code is used to Disarm the Partitions, the
Control panel will rearm the Partitions automatically
when the programmed Patrol Time expires.
nArming in A, B, C or D Mode
(<Code> A, B, C or D)
+DO NOT assign Duress Codes to A, B, C or D
Mode Arming commands.
Each user code can be set up to manage four different
Arming mode configurations: A, B, C and D. These con-
figurations determine the Partitions that will Arm, and
those that will Disarm when an A, B, C or D Mode com-
mand is entered at a Keypad (the final configuration de-
pends on the User code and Keypad Partitions).
+Keypads can operate ONLY on the Partitions they
are assigned to.
nQuick Arming for PREMIUM LCD and CLASSIKA
LCD keypad
1. Press ON: the Keypad will sound a beep.
2. Press and hold the ON key for approximately 3 se-
conds, the Keypad will sound a second beep, and the
display will show the following message:
Quick_arming ___
Type:_A,B,C,D__
3. Press A, B, Cor Dwithin 4 seconds (to Arm in A, B, C
or D mode, as required). If you do not press a key within
4 seconds the Control panel will Arm the Partitions au-
tomatically in Away mode.
Quick Arm operations will affect the Keypad Partitions
and the Partitions assigned to the Quick Arm method.
+Your Installer will tell you which Keypads can be
used, and which Partitions are involved.
You can Arm/Disarm the Partitions separately using a
6-digit User Code PIN, as follows: — type in a 6-digit
User Code PIN followed by the 2-digit ID number of the
Partition concerned , then press ON, OFF, A, B, C or D,
as required. The partition concerned will Arm/Disarm in
accordance with programming.
Example: If the 6-digit User code PIN is 135790, and
you want to Arm Partition 13 in Away Mode, type-in
13579013 then press ON. If you want to Disarm Parti-
tion 13, using the same PIN, type-in 13579013 then
press OFF. If you enter 13579013 then press A, B, Cor
D, Partition 13 will Arm in accordance with the respecti-
ve configuration.
nAbout Partition Arming
If you Arm a Partition with an Exit Time, the Keypad will
emit slow beeps to signal the elapsing Exit Time.
If you arm se
veral Partitions with different Exit Times,
the Keypad will emit slow beeps until all the Partition
Exit Times expire. However, each Partition will Arm
when its own Exit Time ends.
When you enter a valid Arming command at a Keypad,
the Control panel will check for:
a) Zones in Alarm
b) Inactive Zones
c) Bypassed Zones
d) WLS delinquency zone
The Partitions will Arm instantly if none of these conditions
is present. If the system detects zones in Alarm, Inactive
and/or Bypassed and/or WLS delinquency status, the re-
spective message will be shown on the display.
Open Zones!
Arm? âå
Open Zones!
View byp.Zones?â
+The second message only appears if the “Disable
activation with alarmed areas” option has been se-
lected.
If this condition is present:
Øpress Bthen, scroll for the zones concerned.
Ensure that all the zone doors and windows are clo-
sed securely, and that there is no motion in the vici-
nity of motion detectors;
Øpress ESC to abort the command, then retry.
+All zone Alarms must be cleared before Arming the
Partitions otherwise Arming will generate an Alarm.
Inactivity!
Arm ? âå
If this condition is present:
KYO320 OPERATING YOUR SYSTEM FROM A KEYPAD 9

Øpress Bto view the Inactive zones.
Øpress ESC to abort the command, then retry.
Bypassed Zones!
____Arm?___ âå
If this condition is present:
Øpress Bto view the Bypassed zones.
Ensure that no zones have been bypassed (turned
OFF) unintentionally. If necessary, use the ON key to
UnBypass (turn ON) Bypassed zones.
Press ENTER to Arm the Partitions.
+All zones must be unbypassed before Arming the
Partitions otherwise security will be greatly reduced.
In the following example, zone 5 has been BYPASSED.
Zone 005
STBY BYPASSED
+Use A or Bto scroll the zones in Alarm, Inactive or
Bypassed status.
nQuick View Trouble Mode (ENTER)
Your system will continuously check for Trouble condi-
tions. If a Trouble condition occurs, the Amber GLED
on the Keypad will turn ON.
To check current Troubles (from standby):
Press the ENTER key on the Keypad.
(If the Compatibility with EN50131 option has been set,
it will be necessary to set the user code followed by the
ENTER button, then press the ENTER button a second
time).
If several Trouble conditions are present:
Use Aor Bto scroll the list (Table 5 shows the various
Trouble conditions).
Current trouble:
Loss of clock
If you access the View Trouble Mode and no Trouble
conditions are present, the display will show the follo-
wing message:
Current trouble:
none!
Press the ENTER key to exit.
nPartition status enquiry
Press the ON key to view the status of the Keypad Parti-
tions:
DD-I-PZ--DDDDII
---IIIPZZ--DI---
The first line of the display will show (from right to left)
the status of Partitions no. 1 through no. 16, the second
row of the display will show (from left to right) the status
of Partitions no. 17 through no. 32. The hyphen (–) indi-
cates that the Partition is not a Keypad Partition.
The Partition status will be shown for approximately 6
seconds.
+Partition status enquiry is possible on Enabled
Keypads only. If Partition Alarm or Tamper is pre-
sent the respective character will blink.
+“View Trouble” mode provides information regar-
ding zones which generate “Low Battery WLS” and
“WLS Device lost” events. For the event details
(i.e. iinformation regarding the zone concerned),
press D.
Accessing the User menu (<CodeENTER)
(for PREMIUM LCD and CLASSIKA LCd Keypads)
Enter a valid User Code then press the ENTER key to
access the User menu. The User menu will allow Users
to access ONLY the commands they are enabled for.
+You can access the User menu when the Control
panel is Armed or Disarmed.
+(If the Compatibility with EN50131 option has been
set, it will first be necessary to enter the code for
View control unit status mode, then press ENTER
to access the User menu).
Using Aand B, scroll for the required option then press
the ENTER key.
Press ESC as many times as required to step back and
exit the menu.
+Several Users can access the menu at the same
time from different keypads.
10 KYO320

The User menu provides the following options:
rReset Alarms
rStop Alarms
rArm/Disarm
rOvertime request
rOvertime request
rEnable/Disable auto-arm
rEnable/Disable Teleservice
rEnable/Disable Answering device
rDisable buzzer
rChange Telephone number
rProgram PINs
rChange Time and Date
rReset PC Programming
rTest Keypad
rTest Siren
rActivate Outputs
rZone status
rContinuous recording
rMemo
rEvent logger
rClear call queue
rEnable/Disable Timers
rEnable/Disable Key
+Your Installer has programmed your Control panel
with your requirements in mind. Therefore, some of
the options may not be available
This system can manage 195 User Codes. Only the first
User Code (0001) is Active and can operate the
system.
Your Installer will enable and program as many User Co-
des as necessary. The programmed Access Level defi-
nes the User Code Partitions (the Partitions the User
Code can control) and the User Code options (the options
the User Code can access). The menu will show the op-
tions the entered User Code is enabled for.
The following paragraphs describe all the Options on
the User menu.
+The commands will affect ONLY the common Par-
titions of the User Code and Keypad concerned.
nReset Alarms and Tamper
This command will allow you to restore all Alarm signal-
ling devices to Standby, and delete the zone and Parti-
tion Alarm memories.
Once the command has been executed, the display will
show the following message:
USER MENU
done!
If Alarm signalling persists after a Reset Alarms com-
mand, select the Stop Alarms option. The causes of
persistent Alarms must be cleared immediately.
nStop Alarms
This command will allow you to stop and freeze all the
Alarm signalling devices. This status can be undone by
pressing any key. During this phase the Control panel
will be unable to trigger Alarms, and the display will
show the following message:
STOP ALARMS!
STOP ALARMS!
The first line flashes while the second remains fixed.
The Iindicators on Keypads, assigned to any of the
Partitions of the Keypad concerned, will blink.
nArm/Disarm
This command will allow you to Arm or Disarm the Parti-
tions one by one, as follows:
1. Use Aand Bto scroll the Partitions common to both
the Keypad and User Code concerned (the current sta-
tus will be indicated on the second line).
Partition 001
disarmed x
meanings of the X’s that may appear on the second line
can be found in Figure 2.
2. Press the ENTER key to select the required Partition.
The display will show the Arming options, as follows:
1=AWAY 2=STAY
3=STAY_0 4=DIS
3. Press the relevant key to select the required mode:
1- Away
2- Stay
3- Stay with 0 delay
4- Disarm
4. Press the ESC key to step back to the User menu.
nZone status
This command will allow you to turn ON/OFF
(UnBypass/Bypass) the zones of the User Code Partitions.
The display will show the BYPASSED or
UNBYPASSED status, and the current condition of the
zone, as follows:
ØALARM (Alarm conditions present)
ØTAMPER (Tamper conditions present e.g. Wires cut)
ØSHORT (Tamper conditions present e.g. Short-circuit)
ØSTBY (zone in standby status)
KYO320 OPERATING YOUR SYSTEM FROM A KEYPAD 11
— This line will blink
— This line will be solid
Figure 2 Partition status.

+NOTE: You must call your Installer if any zones si-
gnal Tamper or Short-circuit.
1. Use Aand Bto scroll the zones of the Partitions com-
mon to the Keypad and User Code concerned.
zone n. 002
sitting room
2. Press the ENTER key to select the required zone.
The display will show the zone status, as follows
Sitting room
STBY UNBYPASSED
3. Using the ON and OFF keys UNBYPASS (turn ON)
or BYPASS (Turn OFF) the zone, as required.
4. Use A or Bto scroll the zones and continue, or press
the ESC key twice to step back to the User menu.
+Attempts to Arm (turn ON) the Partitions when zo-
nes are Bypassed or in Alarm status will activate
the Zones status list automatically. Only the zo-
nes that are about to be Armed will be included in
the list.
+You can Bypass a Zone using a 6-digit User Code
PIN, as follows: — type in a valid 6-digit User Code
PIN followed by the 3-digit ID number of the Zone
concerned then press ESC. For example, if the
PIN is 135790 and you want to Bypass Zone 23,
type in 135790 023 then press ESC.
nEvent Log
This command will allow you to view and print the
events in the Event Log. The Control panel Event log
can store up to 10,000 events. The events will be stored
in chronological order —starting from the most recent.
Each event shows the following details:
ØEv. (Event number)
ØTYPE (e.g. Zone Alarm, Invalid Code, etc.)
ØIDENT (e.g. Zone number, Partition, etc.)
ØAGENT (e.g. Keypad, Reader, etc.)
ØID.AGEN (e.g. User code, Card/Key, etc.)
ØTIME (Time and Date of the event)
The display will show the following message:
EVENT LOGGER
From Last ...
To view all Events
Press the ENTER key to view all the Events in the
Log—starting from the most recent (from last . . ).
Use Aand Bto scroll the Events.
Press Dto view the Event details (see above).
To view Events from a specific Date
EVENT LOGGER
starting from..
Using A or Bscroll for the following message:
Press the ENTER key, the display will show the Date
prompt.
Starting from..
10/09/2006
Enter all the digits of the required Date (DD/MM/YYYY),
then press the ENTER key.
Use Aand Bto scroll the Events.
Press Dto view the Event details (see above).
Ev.00015 TYPE
Valid code
+The display will show the relevant details for each
Event. For example, Tamper Events show the
TYPE and TIME only.
To print Events from a specific Date
Using Aor Bscroll for the following message:
EVENT LOGGER
print from..
Press the ENTER key, the display will show the Date
prompt.
Starting from...
10/09/2005
Enter all the digits of the required Date (DD/MM/YYYY),
then press the ENTER key.
The Keypad will exit the USER MENU, and the Printer
will print the Events starting from the entered date to the
most recent.
+This facility is provided by the optional K3-PRT2
Printer Interface (ask your Installer for details).
The Event Log
The Event log is set up as follows:
Øthe Event number (Ev.) is shown on the left side of
the first line;
Øthe Event details (TYPE, IDENT., USER, USER ID,
TIME) are shown on the second line.
Ev.00015 TYPE
Valid code
Using the Event Log:
ØUse Aand Bto scroll the Events.
ØPress Dto view the Event details (see above).
ØPress the e to step back to the Event Log menu.
12 KYO320

+The display will show the relevant details for each
Event. For example, Tamper Events show the
TYPE and TIME only.
nEnable/Disable Auto-arm
Your Installer may have set up Partitions to turn
ON/OFF at preset times. This command will allow you
to turn the Scheduler ON/OFF, and Enable/Disable au-
tomatic ON/OFF control.
Use Aand Bto scroll the Partitions, and the ON and
OFF keys to Enable/Disable the Scheduler.
Partition 001
Scheduler OFF
Press the ESC key to step back to the User menu.
nTeleservice request
If your Installer has set up this facility, this command will
allow you to request on-line assistance (maintenance
that does not require components or wiring). Teleservi-
ce requests will be confirmed by the following message:
USER MENU
done!
The Teleservice request will stop any ongoing Telephone
calls (Teleservice requests from the User have priority
over other call types), and will send the Teleservice call (or
calls) to the Installer telephone number (or numbers).
nEnable/Disable Teleservice
This command will allow you to Enable/Disable the
Control panel to receive Teleservice calls. The com-
mand will be confirmed by the following message:
En./Dis. Service
Service OFF
ON to enable procedures with the installer code
OFF to disable procedures with the installer code
Press the ENTER button to confirm and return to the
User menu.
If the user enables the Maintenance mode (Maintenan-
ce ON) and the control unit is connected to the telepho-
ne line, the installer will be able to perform the following
procedures remotely, as well as on site:
ØView the Control panel status — Partition status;
Alarm memory, Bypassed zones, Zone status, Event
logger, Peripheral device status, etc.
ØChange the Control panel status — Change Par-
tition status, Clear the Alarm memory and Bypass
zones (active User Code required).
Ø Change the Control panel parameters — if all the
partitions are disarmed and the Partition Patrol Times
are not active.
The Teleservice facility allows the Installer to check and
work on the Control panel from a remote computer, and
carry out maintenance work that does not require new
wiring or components.
+An *will be shown on the display directly above
the twhen the Teleservice facility is enabled.
nEnable/Disable Answering device
This command will allow you to turn ON/OFF the
Answering device. If the Answering device is ON, the
Control panel will answer incoming calls with a Voice
message. This facility is provided by the K3-VOX2 Voi-
ce board (accessory item).
The Answering device can function even if the
K3-VOX2 Voice board is absent, but in this case there
aren’t voice messages. When you select this com-
mand, the display will show the following message:
En./Dis.Ans.Dev.
Answer dev. OFF
Press ON to Enable the Answering device facility.
Press OFF to Disable the Answering device facility.
Press the ENTER key to confirm and step back to the User
menu.
+If the Answering device facility is enabled, an *will
be shown on the display directly above the r.
nActivating Outputs (Turning ON/OFF
Appliances)
If your Installer has set up your system to control ap-
pliances (sprinklers, lights, etc.), this command will al-
low you to turn the appliances ON/OFF manually.
To turn ON/OFF Outputs (appliances):
1. Use Aand Bto scroll the list.
Output n. 001
Output 001
2. Press the ENTER key to select the required Output
(appliance). The display will show the current status.
Output 001
INACTIVE
3. Press ON or OFF, as required.
Use Aand Bto continue scrolling the list.
4.Press the ESC key twice to confirm and step back to
the User menu.
nClear call queue
If your Installer has programmed your Control panel to
send Alarm calls, it will call the programmed telephone
numbers each time an Alarm occurs. In the event of a
False Alarm, this command will allow you to interrupt
the ongoing call, and clear the call queue.
If you select this command the display will show the fol-
lowing message:
CLEAR CALL QUEUE
Confirm?
To confirm the Command
KYO320 OPERATING YOUR SYSTEM FROM A KEYPAD 13

Press the ENTER key.
The display will show the following message for several
seconds before stepping back to the User menu:
CLEAR CALL QUEUE
done!
To Abort the Command
Press the ESC key to step back to the User menu.
nOvertime request
If the Auto-arm option is enabled, and the system is pro-
grammed to Arm automatically at a preset time, the
Overtime request will allow you to delay the Auto-ar-
ming event.
Acceptance of the Overtime Request will be confirmed
by an audible feed back signal and the following
message:
OVERTIME REQUEST
done!
+If any of the Partitions concerned is unable to im-
plement the Overtime request, the Keypad will emit
an audible error signal.
The Installer will set up the Auto-arm and Overtime Re-
quest events with your installation in mind, and will pro-
vide you with all the necessary information (regarding
the partitions involved, and the number of Overtime re-
quests you can make before an Auto-arm event).
nChange Time and Date
This command will allow you to set the current Date and Time.
+You cannot change the Time and Date when Parti-
tions are Armed.
1. Using A or Bselect NEW TIME - DATE, then press
ENTER.
NEW TIME - DATE
11:48 02/08/2002
2. Enter the New Time and Date, then press ENTER to
confirm and go to the next step (Date format), or ESC to
quit and step back to the USER MENU.
+The New Time and Date field will not allow you to
change the digits individually, therefore, you must en-
ter the entire Time and Date. If you press ENTER be-
fore completion, the setting will be deleted.
Date format
hh:mm dd/mm/yyyy
3. Using Aor Bselect Date format:
hh:mm dd/mm/yyyy
hh:mm mm/gg/yyyy
hh:mm yyyy/mm/dd
then press ESC to confirm and go back to step 2.
nChange Telephone numbers
This command will allow you to change the first eight
Telephone numbers in the Phonebook.
To program or change the Telephone numbers:
1. Using Aand Bscroll the 8 Telephone numbers.
Change tel. num.
Telephone n. 001
2. Press ENTER to select the number to be program-
med or changed.
The display will show the current Telephone number, or
an empty programming field (the first digit will blink to in-
dicate that it is ready for programming).
Telephone n. 002
0735556666
3. Using keys 0through 9, enter the telephone number.
— OFF corresponds to the pound sign (#);
— ON corresponds to pauses (*);
— Cand Dwill allow you to move the cursor along the
line and overwrite wrong digits.
To delete the entire Telephone number, press and hold
1until the keypad emits a beep.
4.Press the ESC key to go back to step 1.
nReset PC programming
When the system is programmed from a computer
(on-site or via Modem) or a Keypad, the Control panel
will trigger the Programming Start event.
The Control panel classifies this event as a Trouble
condition, therefore, it will be signalled on the GLED.
To view this Trouble condi
tion, you must access View
Trouble mode, the display will show the following
message:
Current trouble:
Start program.
To clear this Trouble condition—select the Reset PC
Prog. option from the User menu and press the ENTER
key, the display will show the following message for se-
veral seconds and the GLED will turn OFF (unless the-
re are other Trouble conditions present).
USER MENU
done!
nProgramming PIN codes
If your Installer has set up the User Code hierarchy (Ma-
ster and Slave Codes).
This command will allow Master Codes to select/dese-
lect the Active status of their Slave Codes
(Enable/Disable Slave Codes), and change their Slave
Code PINs.
+This command is available to Master Codes only.
14 KYO320

Active Slave Codes can access the system and control
their enabled Partitions and functions.
To allow/deny system access to a Slave Code:
1. Use Aand Bto scroll the Slave Codes list (accessed
by the Master Code).
Code n. 001
Code 001
2. Press the ENTER key to select the required Code.
Code 001
Active
3. Press the ON key to select Active status, or OFF to
deselect Active status, as required.
+A Code can be both a Master and a Slave (i.e. Sla-
ve of one Code, and Master of another). A Master
Code cannot deselect the Active status of a Slave
Code that is Master of another Slave Code.
To change the PIN of a Slave Code:
1. Use Aand Bto scroll the list of Slave Codes (acces-
sed by the Master Code).
Code n. 001
Code 001
2. Press the ENTER key to select the required Code.
Code 001
Active
3. Press the ENTER key again, the display will show the
following message:
Enter new PIN
PIN ******
4. Enter the new PIN (4 to 6 digits) — * will replace X
as you enter the new digits.
5. Press the ENTER key, the display will show the follo-
wing message:
Repeat new PIN
PIN ******
In the example above, two digits have been entered.
6. Enter the new PIN again, the press the ENTER key to
confirm and go back to step 1.
If necessary, press the ESC: key to abandon the proce-
dure and go back to step 1.
+You cannot assign the default PIN of one code to
another Code (refer to Table 9).
If you attempt to assign the default PIN of one Code to
another Code, the display will show the following mes-
sage:
Repeat new PIN
Invalid code!
+You cannot assign a PIN that already exists on the
system.
If you attempt to assign a PIN that has already been as-
signed to another Code, the display will show the follo-
wing message:
Repeat new PIN
Duplicated PIN!
This message indicates that the PIN already exists on
the system, therefore, the Control panel will consider
the Code to be “Disclosed” and, for security reasons,
will automatically restore the default PIN of the Code
concerned.
If a User attempts to access the system using a “Disclo-
sed” PIN, the display will show the following message:
17:05 26/08/2002
Disclosed_PIN!
Disclosed” PINs (at default) must be reprogrammed
(refer to Table 7).
“Disclosed” PINs will be signalled by:
Øthe GLED (ON) on the Keypad
Øthe Disclosed PIN! message in View Trouble
mode
Øthe Event details in the Logger
TYPE = Disclosed PIN
IDENT. = the Keypad used
TIME = Time and Date of the Event
The Trouble status will clear when a New PIN (other
than the default PIN) is assigned to the Code with “Di-
sclosed” PIN status.
nMemo
This command will allow you to record and play voice
memos. This command must be enabled on Installer
Menu-Program Panel-Configuration-Keypad-Memo.
USER MENU
Memo
Press ENTER:
Memo
Record message
+This option must be duly programmed by the Instal-
ler, (Message n.63 only- Quality and Length must
be programmed on Installer Menu-Program Pa-
nel-Voice Messages) otherwise it will not be availa-
ble on the Keypad.
To record voice memos
1. Press ENTER to start recording.
KYO320 OPERATING YOUR SYSTEM FROM A KEYPAD 15

Memo
RemainingSec.030
The numbers on the second line of the display will indi-
cate the remaining seconds before the end of message.
The Green MLED on the Keypad will turn ON to indica-
te that there is a new memo.
To play voice memos
1.Press Aor Bto display Play message:
Memo
Play message
2. Press ENTER to play the voice memo:
Memo
RemainingSec.030
The numbers on the second line of the display will indi-
cate the remaining seconds before the end of message.
The Green MLED on the Keypad will turn OFF to indi-
cate that there are no unplayed memos.
+You cannot record a new message until the current
message has been played.
nDisable buzzer
If the Keypad buzzer is Enabled, it will signal the Entry
and Exit Times,and Violation on Chime zones. This
command will allow you to Disable these audible si-
gnals.
When you select this command the display will show
the following message:
Disable buzzer
Buzzer OFF
Press OFF to Disable the buzzer.
Press 1to Enable the buzzer with low volume.
Press 2to Enable the buzzer with high volume.
Press the ENTER key to step back to the User menu.
+This command will not Disable the audible feed
back signal sounded by the keys .
nTest Siren
This command will allow you to Test the proper working
order of the Alarm signalling devices. If you select this
command the Control panel will activate the devices,
and the display will show the following message:
Test Siren
done!
nTest Keypad
This command will allow you to Test the proper working
order of the display, LEDs and Keypad. If you select this
command the display will show the following message:
USER MENU
Test keypad
1. Press ENTER:
ABCDEFGHIJKLMNOP
ABCDEFGHIJKLMNOP
If the display is working properly, it will show letters A to
P on both lines.
If the I, a, Gand Mindicator LEDs are working pro-
perly, they will blink for several seconds.
If the buzzer is working properly, it will sound three ti-
mes.
nContinuous recording
This command will allow you to record sounds picked
up by the system microphones, during and after Alarm
and generic events.
To playback sound recording:
1. Use Aor Bto scroll for the Cont. rec. ack option.
+This command cannot be selected until one of the
Events, programmed by the Installer, occurs.
Continuous rec.
Cont.rec.ack
2. Press ENTER to start the sound recording playback
Continuous rec.
RemainingSec.030
The second line of the display will show the elapsing ti-
meout. When the remaining seconds go to zero the
Continuous Recording elapses.
To reset this command:
1. Use Aor Bto scroll for Cont.rec. reset:
Continuous rec.
Cont.rec. reset
2. Press ENTER to reset the Continuous Recording fa-
cility, and step back to the User menu.
nEnable/Disable Timers
This Control panel manages up to 64 Timers for control
of the ON/OFF Times of electrical appliances (Heating
systems, Garden sprinklers, Courtesy lights, etc.), and
Enabled Times of the system objects (Outputs, Codes,
Keys, Cards, etc.). Ask your Installer for details. The
En/Dis Timer option will allow you to Enable/Disable
the Timers, as follows:
1. Use Aor Bto scroll for the Timer concerned.
16 KYO320

Timer 001
Timer ON
2. Press ON to Enable, or OFF to Disable the Timer.
3. Press ENTER to confirm and go back to the User
menu.
nEnable/Disable Key
The En/Dis Key option will allow you to Enable/Disable
the Keys, as follows:
1. Use Aor Bto scroll for the Key concerned, or enter
its ID Number.
Key 001
Key ON
2. Press ON to Enable, or OFF to Disable the Key.
3. Press ENTER to confirm and go back to the User
menu.
+NOTE: A Key can be Enabled/Disabled ONLY by
Codes which operate the Partitions it is assigned to.
KYO320 OPERATING YOUR SYSTEM FROM A KEYPAD 17

18 KYO320

USING DIGITAL KEYS AND CARDS
The Digital Keys/Cards will allow you to perform all the
basic operations from enabled Readers.
Readers
Readers have 3 System status LEDs (Red, Green and
Amber).
+Readers can also be used to signal three specific
events. Ask your Installer for details.
+If the Compatibility with EN50131 option has been
enabled for a reader, after every activation/deacti-
vation the 3 indicator lights will be switched off to
“hide” the control unit status.
This Control panel manages:
ØECLIPSE Readers (see Figure 3b) - These devices
accept commands from SAT Keys (Key must inser-
ted into the key slot on the Reader).
ØPROXI Proximity Readers (see Figure 3d) - These
devices accept commands from Digital Keys and
PROXI-CARDS (the Card/Key must be held near the
sensitive field of the Reader).
ØPREMIUM LCD Keypads (see Fig. 3e) - These Keypads
have built in Proximity Readers Readers and accept com-
mands from Digital Keys and PROXI-CARDS (the
Card/Key must be held near the sensitive field of the Re-
ader).
KYO 320 manages up to 32 Readers. This Control pa-
nel supports up to 32 Readers. The Installer will pro-
gram the following parameters for each Reader:
ØThe Partitions the Reader can control (Reader Parti-
tions)
ØA Mode Arming (AMBER)
ØB Mode Arming (GREEN)
Digital Keys/Cards
This Control panel can manage:
ØSAT Keys (see Figure 3a) - These work with
ECLIPSE and PROXI Readers.
ØPROXI-CARDS (see Figure 3c) - These work with
PROXI Readers only.
The section describes how to operate your system from
a Key/Card Reader. Each Key/Card has a random code
— selected from over 4 billion combinations.
Your Installer can assign an Identifier Number and De-
scription to up to 500 Keys/Cards. The number will be
recorded in the Event Logger each time the Key/Card
KYO320 USING DIGITAL KEYS AND CARDS 19
a)
b)
®
c)
d)
e)
Sensitive
Field
PROXI LEDs
Figure 3 a) SAT Digital key, b) ECLIPSE key reader, c) PROXI-CARD, d) PROXI reader, e) PREMIUM LCD keypad.

operates on the System. The Digital Keys/Cards can be
programmed to operate on specific Partitions.
+In this Manual, the word Reader refers to ECLIPSE
and PROXI Readers.
The Reader LEDs
The ECLIPSE Key and PROXI Card Readers simplify
system control by replacing User Code PINs with high
Security Digital Keys or Cards. The Readers have 3
LEDs, this section describes how the LEDs will signal
the System status.
+If the reader has been set to Compatibility with
EN50131, all the indicator lights will be switched off
at the end of the Exit time and Entry time periods.
nNo Key/Card at Reader
When no Digital Key/Card is present at the Reader, the
LEDs will signal as shown in Table 6.
The Partitions that are not controlled by the Reader will
not affect the LEDs. If the configuration of the Armed
Partitions does not match either A or B Mode Arming
(for example, one of the Reader Partitions has been
Armed via Keypad), neither the Amber nor Green LED
will turn ON.
+The Installer can program the Reader LEDs to si-
gnal the System status at all times, or alternatively,
only in response to a Valid Key/Card (LEDs OFF
when no Key/Card is present).
nKey/Card at Reader
When a Key/Card is present at the Reader, the LEDs
will signal as follows.
a) Fast Blinking on 1 LED - Before Arming the Parti-
tions, the Control panel will check the status of the
Unbypassed (ON) and Instant Zones. If a Zone is ‘Viola-
ted’ (e.g. door or window open), the LED, associated
with the selected Arming Mode, will blink quickly. If this
occurs, DO NOT ARM the System, as Arming will trig-
ger a False Alarm.
+It takes the Control panel about 2 seconds to check
all the Zones.
+False Alarms can be stopped by simply Disarming
the system (refer to “Digital Key/Card Reader ope-
rations” in this section). If you accidentally trigger
an Alarm, call the Central Station to prevent the
operator from taking unnecessary action.
+If, when you Arm the system, the Control panel de-
tects Autobypassable zones in Alarm status, it will
bypass them automatically. In this way, false
Alarms will not be triggered, however, Bypassed
zones will be UnBypassed automatically when the-
ir Partitions are next disarmed.
b) Fast Blinking on all 3 LEDs - This will occur when a
False Key/Card is present at the Reader.
c) Slow Blinking on all 3 LEDs (ECLIPSE Readers
only) - This Mode will allow you to restore the previous
setting (reset the Arming Mode that was active before
the SAT Key was inserted. To Reset: push the SAT Key
into the ECLIPSE Reader until the 3 LEDs start to blink
slowly, the previous setting will be restored when you
remove the Key.
d) Red LED ON - The System will Arm when you remo-
ve the Key/Card from the Reader.
e) Amber LED ON - The System will Arm in A Mode
when you remo
ve the Key/Card from the Reader.
f) Green LED ON - The System will Arm in B Mode
when you remove the Key/Card from the Reader.
+Your Installer may have Disabled the Reader
LEDs, therefore, they will not turn ON even when a
valid Key/Card is used.
Multiple Systems
The Digital Keys/Cards can be programmed (by the
Installer) to operate on more than one System, and to
manage different Partitions on each System.
20 KYO320
TABLE 6 - LED Status with no Key/Card at Reader
LED Status Meaning
RED
OFF All of the Reader Partitions are Disarmed
ON At least one of the Reader Partitions is Armed
Slow
Blinking
At least one Alarm or Tamper event has been detected on one of the Reader Partitions
and ALL the Reader Partitions are Disarmed
Fast
Blinking
At least one Alarm or Tamper event has been detected on one of the Reader Partitions
and AT LEAST ONE of the Reader Partitions is Armed
YELLOW ON The Reader Partitions are Armed in AMode
OFF The Armed/Disarmed status of the Reader Partitions does not match AMode
GREEN ON The Reader Partitions are Armed in BMode
OFF The Armed/Disarmed status of the Reader Partitions does not match BMode