Berkel 823E Owner's manual

823E,825E&A,827E&AOWNER/OPERATORMANUAL • 15
OWNER/OPERATOR
MANUAL
IMPORTANT NOTICE
This manual contains Important Safety
Instructions which must be strictly
followed when using this equipment.
MODELS 823E,
825E, 825A,
827E & 827A
SLICERS
NOTICIA IMPORTANTE
Este manual contiene importantes instrucciones
de seguridad que deben ser seguidas el pie de la
letra cuando utilice esta maquina.

14• 823E,825E&A,827E&AOWNER/OPERATORMANUAL
BEFORE USING THIS EQUIPMENT
Berkel’s slicers are designed to slice meat and other food products safely
and efficiently. However, unless the operator is properly trained and
supervised, there is the possibility of a serious injury. It is the responsi-
bility of the owner to ensure that this slicer is used properly and safely,
strictly following the instructions contained in this manual and any re-
quirements of local law.
No one should use or service this slicer without proper training and
supervision.All operators should be thoroughly familiar with the proce-
dures contained in this manual. Even so, Berkel cannot anticipate every
circumstance or environment in which its slicers will be used. You, the
owner and operator, must remain alert to the hazards posed by the func-
tion of a slicer—particularly the sharp rotating blade and moving table.
No one under 18 years of age should operate this equipment. If you are
uncertain about a particular task, ask your supervisor.
This manual contains a number of safe practices in the General Safety
Instruction Section.Additional warnings are placed throughout this
manual. WARNINGS RELATEDTOYOUR PERSONALSAFETY
ARE INDICATED BY:
WARNING
If any warning label, wall chart or manual becomes misplaced, damaged
or illegible, please contact your nearest distributor or Berkel directly, for
a free replacement.
Remember, however, THIS MANUALOR THE WARNINGLA-
BELS DO NOT REPLACE THE NEED TO BEALERTAND TO
USE YOUR COMMON SENSE WHEN USINGTHIS SLICER.

823E,825E&A,827E&AOWNER/OPERATORMANUAL • 1
TABLE OF CONTENTS
Page
General Safety Instructions ....................................................................................................2-3
Equipment Description ..............................................................................................................4
Installation .................................................................................................................................5
Testing Prior to Operation .........................................................................................................5
Operating Instructions ...............................................................................................................6
Sharpener Maintenance ............................................................................................................. 6
CleaningInstructions
CleaningSharpeningStones...............................................................................................7
CleaningandSanitizing......................................................................................................8
Cleaning the Knife .............................................................................................................8
Reassembly ........................................................................................................................9
Sharpener Instructions ...............................................................................................................9
Troubleshooting .......................................................................................................................10
Repair Parts/Repair Service.....................................................................................................12
Specifications...........................................................................................................................12
Warranty..................................................................................................................................13
Berkel Company • World’s Leading Manufacturer of Slicers and Food Processing Equipment
BERKEL COMPANY
4406 Technology Drive · South Bend, Indiana 46628-9700
574/232-8222 · Fax [phone]
[phone]
Form No. 4382R0202 Printed in USA Berkel Company Part No. 3175-0817

2• 823E,825E&A,827E&AOWNER/OPERATORMANUAL
PELIGRO
CUCHILLAFILOSA
para evitar serios accidentes a su
persona siga las instrucciones de este
manual y
1. NUNCA utlice esta mçquina sin previa instrucciùn y autorizaciùn de su
supervisor.
2. LA MçQUINA DEBE apoyarse sobre un nivel solido y plano.
3. LOS PROTECTORES deben colocarse ANTES de enchufar y operar la
mçquina.
4. SIEMPRE utilice el enchufe original proveido por el fabricante.
5. SIEMPRE utilice el utensillo para empujar la
comida - nunca su mano.
6. NUNCA TOQUE LA CUCHILLA CON
LA MANO.
7. MANTENGA manos, brazos, cabello y
ropa suelta LEJOS de toda parte en movimiento
de la mçquina.
8. EN CASO DE QUE LA MÇQUINA SE TRABE,
apague y desconecte ANTES de sacar lo que la obstruye.
9. APAGUE Y DESCONECTE LA MçQUINA antes de limpiar,
sanitizar, o arreglar.
10. UTILIZE UNICAMENTE los repuestos provistos por el fabricante.
11. EN CASO de que los membretes de ‘PELIGRO’ se desprendan
de la mçquina o sean illegibles, llame al fabricante o a su
representante de service Berkel para que lo reemplace sin cargo.

823E,825E&A,827E&AOWNER/OPERATORMANUAL • 3
WARNING
SHARP KNIFE BLADE
to avoid serious personal injury
follow all the instructions in this manual
and
1. NEVER touch this machine without training and authorization by your
supervisor.
2. MACHINE MUST BE on solid level support.
3. GUARDS MUST BE in place before plugging in and turning on machine.
4. ALWAYS use three pronged plug provided.
5. ALWAYS use food pusher not your hand.
6. NEVER TOUCH ROTATING KNIFE.
7. KEEP hands, arms, hair and loose clothing
clear of all moving parts.
8. SHOULD MACHINE JAM, turn off and unplug
before removing obstruction.
9. TURN OFF AND UNPLUG machine from power source before cleaning,
sanitizing or servicing.
10. USE ONLYthe attachmentsprovided by the manufacturer.
11. SHOULD any warning label on a machine come off or become unreadable
contact the manufacturer or your designated Berkel service location for a
free replacement.

4• 823E,825E&A,827E&AOWNER/OPERATORMANUAL
MODEL827A
Sharpener Pusher
Product Table
Center Plate
Center Plate
Locking Knob
Thickness Control
Knob
Start/Stop
Switch
Product Table
Handle
Slice Deflector
Gauge Plate
Pilot
Light

823E,825E&A,827E&AOWNER/OPERATORMANUAL • 5
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678
WARNING
To avoid serious personal injury properly
install slicer in adequate work area
• ALWAYSusequalifiedtechnicianforinstallation.
• ALWAYS install slicer in work area with adequate light and space.
• ONLY operate slicer on a solid, level support.
• NEVER bypass or alter switches or circuits.
• NEVER operate slicer without all guards installed.
• NEVER operate slicer without all warning stickers and wall charts posted.
INSTALLATION
UNPACKING AND ASSEMBLY
1. When the slicer has been unpacked and removed from its shipping carton, it should be
checked carefully for any damage that may have occurred during shipment. Do not plug in
the power cord or attempt to operate the slicer prior to this examination.
2. Carefully check all slicer components such as the product table, pusher, sharpener, thick-
ness control knob, etc., to make certain they move freely and that there are no obstruc-
tions. Turn the thickness control knob as far right as possible. Lubricate the pusher slide
bar (on the product table) and the square and round table support rails (underside of slicer)
with Berkel Food Machine Oil.
TESTING PRIOR TO OPERATION
1. Make sure that the ON/OFF switch is in the OFF position, and the thickness control knob
is turned as far to the right as possible. This positions the gauge plate so that the knife is
not exposed during testing.
2. Plug power cord into grounded 120V AC electrical outlet.
WARNING
Use only USDA-authorized oil on this slicer. Non USDA-authorized oil may contaminate
this slicer and cause food poisoning and personal injury. Berkel Food Machine Oil is an
USDA-authorized oil for food processing equipment. Berkel Food Machine Oil can be
purchased in 2 oz. bottles (Part #4675-0182), pints (Part #4675-0183) or gallons (Part
#4675-0184).

6• 823E,825E&A,827E&AOWNER/OPERATORMANUAL
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678
3. Slide Product Table back and forth holding on to the Product Table Handle. If there is any
rough operation or obstruction, shut off, unplug power cord and call your Berkel service-
man.
4. Turn the slicer ON and check for smooth knife rotation. Turn the slicer OFF.
OPERATING INSTRUCTIONS
1. Rotate the pusher out of the way of the product table. Place product to be sliced on the
product table. Position the pusher at the end of product. If the product you’re slicing is
long, place the pusher on top of the product. The pusher will feed the product toward the
knife after each slice.
2. Turn the slicer ON.
3. The thickness control knob allows you to vary the thickness of the slices from paper thin to
approximately 9/16” thick. To make thinner slices, turn the thickness control knob to the
right. For thicker slices, turn the knob to the left.
4. A handle is provided on the product table to move it back and forth.
5. After each use of the slicer, turn the slicer OFF and the thickness control knob full right.
This places the gauge plate in the closed position and covers the knife edge.
WARNING
WHENMOVING THEPRODUCT TABLE,GRASP
ONLY THE PRODUCT TABLE HANDLE.
SHARPENER MAINTENANCE
1. Turn OFF the slicer, turn index knob fully to the right and unplug the power cord from the
receptacle.
2. Loosen sharpener lock knob and lift off the sharpener.
WARNING
ONLY USE THE PRODUCT TABLE HANDLE TO MOVE THE PRODUCT TABLE.

823E,825E&A,827E&AOWNER/OPERATORMANUAL • 7
3. Clean the cover with water and detergent. Carefully clean around the stones. DO NOT
submerge the sharpener assembly. Should the assembly accidently get wet, dry completely
and oil the assembly thoroughly with Berkel Food Machine Oil before reinstalling.
4. Check the stones. If they do not turn freely, are greasy or are full of metallic build-up, they
must be cleaned. (See “Cleaning the Sharpening Stones,” page 7). If the stones are
cracked or chipped they must be replaced.
5. Oil sharpener shafts. Place a few drops of Berkel Food Machine Oil on each shaft. Move
the sharpening and deburring stone push buttons back and forth to make sure that the
stones move in and out easily. Also, rotate the stones to make sure they turn freely.
6. Oil the mounting post.
7. Replace sharpener. Sharpener must be all the way down protecting the top of the knife.
Lock in place.
CLEANING INSTRUCTIONS
CLEANING SHARPENING STONES
Each time the sharpener is used, the sharpening stones should be examined for cleanliness.
Turn off slicer, close the gauge plate, unplug power cord and remove sharpener. If there is
evidence of fatty or metallic build-up in the stones, they must be cleaned. Otherwise, they will
not have the abrasive quality necessary to sharpen.
Clean as follows:
1. Remove the nuts and take the stones off the shafts.
2. Soak the stones in a solution of dish soap (i.e. Joy, Dawn, etc.) and water for one hour.
3. Scrub stones with a stiff bristle brush (Berkel Part # 4975-9237).
4. Rinse thoroughly at a sink.
CAUTION
DirtyStonesCannotSharpen!
IF THE SHARPENING STONES HAVE BECOME COATED WITH FOOD FATS
OR METALLIC BUILD-UP, THEY WILL NOT SHARPEN EFFECTIVELY.

8• 823E,825E&A,827E&AOWNER/OPERATORMANUAL
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1
23456789012345678901234567890121234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567
8
1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212345678
5. Shake excess water out and pat partially dry with paper toweling or a clean cloth towel.
Set aside to air dry.
6. Once the stones are dry (after 24 hours), oil the shafts with Berkel Food Machine Oil.
7. Reassemble.
Berkel recommends that a spare set of stones (Berkel Part # 825-00112) be kept available for
thorough cleaning procedures, and in case of breakage, so you will not lose your sharpening
capabilities.
CLEANING & SANITIZING
1. Turn slicer OFF and unplug the power cord.
2. Turn the thickness control knob all the way to the right to close the gauge plate.
3. Remove the product table locking knob.
4. Remove the product table.
5. Remove the slice deflector which is attached to the main slicer body.
6. Unscrew the center plate locking knob. Push on the knob to move the center plate off the
knife. Remove both the center plate and the locking knob.
7. Clean and sanitize removed parts. Wash these parts in hot water with detergent, rinse in hot
water and rinse again in sanitizing solution. Let the parts air dry. Berkel recommends using
USDA approved sanitizer, Berkel part number 4975-00400.
CLEANING THE KNIFE
1. Switch slicer off and unplug the power cord.
2. Make sure thickness control knob is fully to the right, so the gauge plate covers the knife.
3. Clean front of knife, moving from center outward.
WARNING
THE PUSHER CAN SLIDE OR ROTATE, SO KEEP THE
PRODUCT TABLE LEVEL IN THE NEXT STEP.

823E,825E&A,827E&AOWNER/OPERATORMANUAL • 9
4. Clean back of knife. Repeat cleaning both front and back of knife with clear water.
Always move from the center outward. NEVER MOVE YOUR HAND TOWARDS
THE EDGE OF THE KNIFE. Sanitize and allow to dry.
REASSEMBLY
1. Be certain the thickness control is fully to the right.
2. Place center plate over the knife.
3. Place a drop of Berkel Food Machine Oil on the threads of the center plate knob.
4. Insert center plate locking knob and tighten. Make snug but DO NOT overtighten.
5. Replace slice deflector.
6. Replace product table. Hold the product table with both hands and set it carefully in place.
REMEMBER that the pusher is loose and can slide.
7. Tighten the product table locking knob.
8. Coat the pusher rod with a thin film of Berkel Food Machine Oil and move the pusher
back and forth to distribute the oil.
9. Check the guards. Make sure slice deflector, sharpener and center plate knife guard are in
place and clear of the knife. Also, make sure that the product table moves back and forth
easily.
10. Clean slicer base. Use a cloth and cleaning solution. Rinse with hot water. Sanitize and let
air dry.
11. Plug in the power cord.
SHARPENING INSTRUCTIONS
CAUTION
KNIFE SHOULD BE SHARPENED AT A MINIMUM ON A DAILY BASIS.
DO NOT SHARPEN A KNIFE THAT IS NOT CLEAN. YOU WILL DAMAGE THE
SHARPENING STONES AND BE UNABLE TO SHARPEN THE KNIFE.
1. Switch OFF the power.

10• 823E,825E&A,827E&AOWNER/OPERATORMANUAL
2. Unplugthe slicer.
3. Turn the thickness control knob to the right to place the gauge plate in the fully closed
position.
4. Clean the knife completely. Always clean from the center towards the outside edge of the
knife. Never move your hand towards the edge of the knife.
5. Loosen the sharpener locking knob, raise and rotate the sharpener until the stones sit with
one on each side of the knife. Retighten the knob to hold the sharpener in its sharpening
position.
6. Plug in the slicer and switch ON the power.
7. Press the sharpening stone push-button to bring the stone against the knife and hold it for
five to 10 seconds and release. When the shapener is in the sharpening position, the
sharpening stone push-button is on the left side of the knife.
8. Press the deburring stone pushbutton to bring the stone against the knife and hold it for
two or three seconds and release. When the shapener is in the sharpening position, the
deburring stone push-button is on the right side of the knife.
9. Switch OFF the power.
10. Return the sharpener to its stored position and lock in place.
11. Clean slicer before slicing product. (See “Cleaning and Sanitizing,” page 8).
Your slicer is now sharpened, cleaned and sanitized—ready to use.
TROUBLESHOOTING
Should your slicer fail to function properly, here are a few things you can check before calling
a Berkel Serviceman.
Product not slicing properly; thick and thin or irregular slices
1. Is the knife sharp? If not, sharpen according to instructions (page 9). Remember, only
sharpen a clean knife.
2. Does the product size exceed the capacity of the slicer? Too large a product may rub
against the sharpener assembly causing interference to normal slicing.
3. Is the product positioned correctly and held securely on product table? If not, product may
move or rotate during slicing operation resulting in partial or thick and thin slices.

823E,825E&A,827E&AOWNER/OPERATORMANUAL • 11
4. Are all components held securely in place? A loose product table or pusher can cause
inconsistent slices.
Knifenotsharpening
1. Are sharpening procedures being followed exactly as explained in this manual (page 10).
2. Are sharpening stones clean? If not, clean according to instructions given in “Sharpener
Maintenance” section (page 7).
3. Is the knife clean? If coated with food fats, sharpener stones cannot sharpen. Clean per
instructions (page 7).
4. Are sharpening stones making solid contact with the knife? If not, have your Berkel
serviceman adjust them to the proper height.
5. Are sharpening stones severely worn and not making contact with the knife? Are the
sharpening stones cracked or chipped? If so, have your Berkel serviceman replace and
adjust the new stones to the proper position for best sharpening results.
Electricalfailure
1. Is slicer fully plugged into a properly grounded 120/AC outlet? If properly connected, the
red or white power on light should be on when switch is in the ON position.
2. Inspect power cord. Has it been damaged, cutting off electrical flow? If so, call your
Berkel serviceman to replace the power cord.
3. Is ON/OFF switch in the ON position?
4. Are you getting electricity from the wall outlet? Check by plugging in another piece of
equipment with the same electrical requirements. Also, check circuit breaker or fuse
5. If you are getting electrical power and your slicer is still not operating, contact your Berkel
serviceman.
Thicknesscontrolknobnotoperatinggaugeplate
1. If the thickness control knob is not opening and closing the gauge plate properly, it is a
sign that the internal mechanism has suffered some loss of adjustment. Do not try to adjust
the mechanism yourself. Call your Berkel Serviceman.
If correction of any of the above conditions does not result in a functional slicer, call your
Designated Berkel Service Location.

12• 823E,825E&A,827E&AOWNER/OPERATORMANUAL
REPAIR PARTS/REPAIR SERVICE
Please contact your Designated Berkel Service Location for any repair parts and/or repair
service required on your Berkel slicer. Additional information may be obtained from:
Service Support Center
Berkel Company
4406 Technology Drive
South Bend, Indiana 46628-9700
574/232-8222 · Fax [phone]
[phone]
SPECIFICATIONS
823E 825E 825A 827E 827A
DIMENSIONS
Width 151/2"(394mm) 171/2"(445mm) 171/2"(445mm) 171/4"(438mm) 20"(508mm)
Depth 183/4"(476mm) 211/8"(537mm) 211/8"(537mm) 22"(559mm) 251/4"(641mm)
Heighth 141/2"(368mm) 143/4"(375mm) 15"(381mm) 16"(406mm) 167/8"(429mm)
KNIFE 9" (220 mm) 10" (250 mm) 10" (250 mm) 12" (300 mm) 12" (300 mm)
MOTOR 1/4hp; 2.5A 1/4hp; 2.5A 1/4hp; 2.5A 1/4hp; 2.5A 1/3hp; 2.5A
120-60-1 120-60-1 120-60-1 120-60-1 120-60-1
NET WEIGHT 29 lb. (13 kg) 33 lb. (15 kg) 37 lb. (17 kg) 41 lb. (19 kg) 60 lb. (28 kg)
MAXIMUM 9/16" (14 mm) 9/16" (14 mm) 9/16" (14 mm) 9/16" (14 mm) 9/16" (14 mm)
SLICE THICKNESS
CUTTING CAPACITY
Width 71/8"(181mm) 71/2"(191mm) 83/4"(222mm) 83/4"(222mm) 103/4"(273mm)
Heighth 6"(152mm) 6"(152mm) 6"(152mm) 71/4"(184mm) 75/8"(194mm)
Diameter 6"(152mm) 7"(178mm) 7"(178mm) 7"(178mm) 73/8"(187mm)

823E,825E&A,827E&AOWNER/OPERATORMANUAL • 13
Warranty
Berkel Company (“Berkel”) warrants to the Buyer of new equipment that said equip-
ment, when installed in accordance with our instructions and subjected to normal use, is
free from defects in material or workmanship for a period of one (1) year from the date
of sale.1
BERKEL SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR EXPRESS OR IMPLIED WARRANTY OF FIT-
NESS FOR A PARTICULAR PURPOSE.
Berkel’s obligation and liability under this warranty is expressly limited to repairing or
replacing equipment that proves to be defective in material or workmanship within the
applicable warranty period. Berkel or a Designated Berkel Service Location will per-
form all repairs pursuant to this warranty. Berkel expressly excludes responsibility for
incidental or consequential damages to buyer or any third party, including, without
limitation, damages arising from personal injuries, lost profits, loss of business opportu-
nity, loss of property, economic losses, or statutory or exemplary damages, whether in
negligence, warranty, strict liability or otherwise.
This warranty does not apply to: periodic maintenance of equipment including but not
limited to lubrication, replacement of worn blades, knives, stones, knobs, accessories,
and miscellaneous expendable supply items, and other adjustments required due to
installation set-up or normal wear.
These warranties are given only to the first purchaser from a Berkel Authorized Chan-
nel of Distribution. No warranty is given to subsequent transferees.
The foregoing warranty provisions are a complete and exclusive statement of the war-
ranty between the buyer and seller. Berkel neither assumes nor authorizes any persons
to assume any other obligation or liability connection with said equipment.
1Model 180 slicers carry a 90-day warranty.