Berkel X13E User manual

Features
Accessories
!Vegetable chute with pusher
!
!
Skewers with coring tool
Slaw tray
Standard features
!1-speed, 1/2 HP, permanently lubricated ball bearing
knife motor with thermal protection
!Furnished in 115/60/1, 7 am ps, AC, with 3 wire cord
and plug (see below for optional voltages)
!LED indicates power to the slicer
!One-piece FDA polymer base and product table for
reduced seams, accessibility and easy cleaning
!
!
!
!Large product table with extra capacity:
"Squares up to 7- Ω
!Articulating and full length rear mounted meat pusher
!Ergonomic, multi-grip handle to advance product table
!Submersible, removable product table mounted
sharpener for consistent sharpening and easy cleaning
!
!No-volt release requires restarting the slicer after a
power interruption
!Permanent ring guard protects entire non-slicing
portion of the knife
!Sealed start/stop switches conveniently located on the
index knob housing out of the food zone
!
Item #___________________________________________
Manual Gravity Feed Slicer
Approved By:
Date
Berkel Company ï 4406 Technology Drive ï South Bend, IN 46628-9700
574-232-8222 ï 800-348-025 ï 1 FAX [phone] ï www.berkel.com
Power Options
!1/2 HP, 220/50/1, 3.5 amps, AC, ETL Listed
!1/2 HP, 220/60/1, 3.5 amps, AC, ETL Listed
Simple kick stand for easy cleaning under the slicer
Model X13E
Model X13E
with fence to secure and advance products evenly
Borazon sharpening stones for fast, accurate
sharpening and extended life
Berkel model X13E manual gravity feed slicer offers a
number of special features. A sanitary one piece
engineered polymer base and product table reduces
seams and joints while providing an FDA approved
surface for easy, effective cleaning. A removable and
submersible table mounted sharpener with borazon
stones for accurate sharpening. Precise thickness
control is achieved using a variable pitch barrel cam for
fine adjustment and wafer thin slices. The index knob
and operating controls are mounted outside of the drip
zone for quick and easy access. A permanent ring guard
protects the entire non-slicing portion of the knife
during slicing and cleaning. A simple kick stand
supports the slicer for easy access to clean under the
slicer. A fence is provided for extra holding of small
products.
Form # SPC34-1106N
Index knob conveniently located outside the drip zone
in the upper left to provide quick and easy access
Variable pitch barrel cam for ultra fine, precise slice
adjustment to a thickness of 1-5/16" (34mm)
13" (330mm) diameter, hollow ground, hardened
and polished forged stainless steel knife
î(190 mm)
"Rounds up to 8-Ωî(220 mm) diameter
"Rectangles up to 10-Ωîx6- æî(265 mm x 170 mm)
Manual Gravity Feed Slicer Model X13E

Litho in USA
SPECIFICATIONS
Motor: 1-speed, 1/2hp totally enclosed and permanently
lubricated ball bearings, thermally protected.
Electrical: Furnished in 115/60/1, 7 am ps, AC, ETL Listed,
with 3-wire cord and plug. Power options noted on page 1.
Finish/Construction: Base, product table, pusher, support
arm and upper housing are constructed of FDA approved,
engineered polymers reducing the number of seams. Gauge
plate and center plate are anodized aluminum. All controls are
sealed and located out of the drip zone.
Knife Sharpener: Removable and submersible table
mounted, two stone, dual action design to ensure correct
Cutting Capacity:Shown in chart above.
No-volt Release: Requires restarting the slicer in the
event of a power interruption.
Knife Ring Guard: Permanent tapered guard covers
the non-slicing portion of the knife edge.
Controls: Sealed push-button switches located on the
index knob housing out of the drip zone.
As we continually strive to improve our products, specifications are
necessarily subject to change without notice.
Model Cutting Slice Knife Product Dimensions
No. Capacity Thickness Dia. Width A Depth B Height C
Rect. 10-1/2î x 6-3/4î (265 x 170 mm) 1-5/16î 13î
Square 7-1/2î (190 mm) (34 mm) (330 mm)
Round 8-1/2î (220 mm)
Motor Electrical Weight Box Dimensions
Width Depth Height
1-speed 115/60/1
1/2 HP 7 amps
Manual Gravity Feed Slicer
AB
C
Kick Stand: A simple kick stand supports the slicer
for easy access to clean under the slicer.
X13E
pressure and contact angle are always applied, thus reducing
knife wear and delivering a perfect edge. Borazon stones
last longer, sharpen faster and clean easier.
Product Table: Full gravity feed 45° angle with
articulating rear mounted pusher that runs the entire
length of the table to secure product for increased yield
and consistency in every slice. A fence is provided for
holding small products.
Warranty: Parts, labor and travel coverage for one
year, exclusive of wear items. 3 year replacement
guarantee for polymer parts.
Form # SPC34-1106N © 2006 Berkel Company
Model X13E
Knife: 13" (330mm) diameter, hollow ground, hardened
andpolished stainless steel.
Thickness Control: Index knob controls a precision, variable
pitch barrel cam with ultra-fine adjustment in the first revolu-
tion and opens to a thickness of 1-5/16" (34 mm) for accurate
and consistent slicing. This control is located out of the drip
zone on the upper left to provide quick and easy access for
operation and cleaning.
5
28î 29î 25î
(710 mm) (735 mm) (635 mm)
26-1/2î 31î 25-1/2î
(780 mm) (650 mm)(675 mm)
Net 86 lb (39 kg)
Ship 116 lb ( 3 kg)
Manual Gravity Feed Slicer Model X13E
Berkel Company ï 4406 Technology Drive ï South Bend, IN 46628-9700
574-232-8222 ï 800-348-025 ï 1 FAX [phone] ï www.berkel.com