Berlin Gardens Mayhew Chat User manual

Mayhew Chat
Dining Swivel Rocker
Assembly Guide
Tools Required
Hardware Included
Bottom View of Seat
Back of Seat Front of Seat
Narrower Space between
seat support and end of seat.
Wider Space between
seat support and end of seat.
Side View of Seat
Back of Seat Front of Seat
Step 1A
Put one of the side
assemblies on a soft
surface and place the
seat onto it by fitting the
mortis and tenons of the
two pieces togther. Use
the examples above to
ensure the front and back
of the seat are correctly
located.
Step 1B
Use the 5/32 Allen Drive Bit to drive 2 - 1/4" x 1 1/2"
Lags through the pre-drilled holes in the side of the
seat where indicated above. You may need to reverse
your drill several times before you are able to drive
the lags in completely. Using the #2 Square Drive Bit,
finish fastening the seat by driving 4 - 2" Pandeck
Screws through the pocket holes located in the very
front and back cross pieces of the seat.
6 - 5/16" X 1 3/4"
Allen Head Bolts
6 - 5/16"
Flange Nuts
6 - 5/16"
Lock Washers
6 - 5/16"
Square Nuts
3 - Fiberglass Springs
3 - Aluminum Plates
1 - Swivel Mechanism
6 - 5/16" X 1 1/4"
Allen Head Bolts
Step 1A Detail
Step 1B Detail
1/4" x 1 1/2"
Lag
2" Pandeck
Screws
Step 2 Detail
1 - Aluminum Seat Bracket
Aluminum Seat Bracket
Side with holes closest
to the edge should be
turned towards the back
of the chair seat as shown.
Step 2
Position the Aluminum Seat Bracket on the
underside of the chair seat as shown above
by driving 2 - 1/4"x 1 3/4" Lags through the
holes in the seat bracket and into the predrilled
holes in the seat. Fasten it only on the side of
the chair seat that you attached in step 1.
1/4" x 1 3/4" Lags
4 - 1/4" X 1 1/2"
Allen Head Lags
4 - 1/4" X 1 3/4"
Allen Head Lags
4 - 1"
Buglehead
Screws
Cordless Drill #2 Square Drive
Bit (Included) 5/32" Allen Drive
Bit (Included) Allen Wrench
(included)
Wrench

Step 6
Fasten the Swivel Mechanism to
the Figerglass Springs, using
2-Aluminum Plates, 6 - 5/16"x 1 3/4"
Allenhead Bolts, Lock Washers
and Square Nuts. Only hand tighten
the nuts until all six bolts are
installed then fully tighten.
Step 3
Fit the Back into place by
placing the poly tabs at the
ends of the back supports into
the cutouts in the back leg of
the side assembly. Fasten
using 1 - 1" Buglehead Screw
for each poly tab.
Step 4
Attach the second side
assembly by repeating
Steps 1 - 3.
Step 3 Detail
1" Buglehead Screw
Step 5 Detail
Step 5
Using 6 - 5/16"x 1 1/4" Allenhead Bolts
and 5/16" Flangenuts, fasten the
3-Fiberglass Springs and 1 - Aluminum
Plate to the seat bracket The Springs
should point towards the front of the
chair. Only hand tighten the nuts until
all six bolts are installed, then align the
springs and fully tighten.
Step 7
Lift the top of the chair
and set the swivel stem
into the receiver of the
base. Push firmly onto the
chair until it sits securely
in the receiver.
5/16" Flange Nuts
5/16" x 1 1/4" Bolts
Aluminum Plate
Fiberglass Springs
Step 6 Detail
Fiberglass Springs
5/16" x 1 3/4" Bolts
Aluminum Plate
Aluminum Plate
Swivel Mechanism
5/16" Lock Washers
5/16" Square Nuts