Berlin Gardens Double Comfo-Back Glider PCTG2400 Firmware update

#PCTG2400, #PZTG2400
Firmly tap bolts into pre-drilled
holes before tightening.
CORRECT INCORRECT
1 2 34 5
Use to measure bolts
Double Cozi-Back Glider
Assembly Directions for
Double Gliders
PACKAGE CONTENTS
2Bases
1Back
1Seat
1 Hardware Package
2 Arms with Legs
2 Cross Supports
4Stops
TOOLS NEEDED:
Hammer
⁄" Wrench
½" Wrench
Allen Wrench
(Included)
Double Comfo-Back Glider
HARDWARE PACKAGE
8 • ¼” x 2” Allen Head Bolts
2 • ¼” x 4½” Allen Head Bolts
2 • ¼” x 3½” Allen Head Bolts
7 • ¼” x 3” Allen Head Bolts
8 • ⁄” x 2 1/2” Allen Head Bolts
8 • ⁄” Lock Nuts
8 • ⁄” Flange Nuts
19 • ¼” Flange Nuts
4 • ⁄” Acorn Nuts
4 • Aluminum Spacers
4 • Glider Brackets
1 • Allen Wrench
Back Slat
Seat Slat
Leg Brace
Seat
Support
Base Assembly
Leg
Right Arm
Le Arm

STEP #3 - Using 4- ⁄" x 2½" Allen Head Bolts,
place them into the pre-drilled holes in the
bottom of the legs and tighten using 4- ⁄"
Flange Nuts. (Ensure the Bolts are pointing
inwards.)
⁄" x 2½" Allen Head Bolts
Assembly Directions for
Glider Chair
Step #1
Fasten the Arm and Leg Assembly to the Seat
and Back using ¼” Allen Head Bolts (size is
specied below). Using a hammer, rmly tap the
Bolts until they are ush with the poly surface.
Securely tighten using ¼” Flange Nuts.
¼” x 3” Allen Head Bolt
¼” x 3½” Allen Head Bolt
¼” x 4½” Allen Head Bolt
Step #2
Turn the chair on the other side and repeat
Step #1.
¼” x 3” Allen Head Bolt
¼” x 3½” Allen Head Bolt
¼” x 4½” Allen Head Bolt
Step #1
Step #2

STEP #1 - Fasten the two Cross Supports to the Base
using 8- ¼" x 2" Allen Head Bolts and 8-
¼" Flange Nuts.
STEP #3 - Locate the predrilled holes located on
outside edge of glider base and install glide
assembly (see next step).
STEP #2 - Attach the four Glider Stops to the Base
using 4- ¼" x 3" Allen Head Bolts and
4- ¼" Flange Nuts. Insert the Allen Head
Bolts into the Poly Glider stops and place
into pre-drilled holes on base. Firmly
fasten with the a ¼" ange nut.
Assembly Directions for
Glider Base
¼" x 2" Allen Head Bolts
¼" x 3" Allen Head Bolts
Front of Base
Back of Base

Firmly tap bolts into pre-drilled
holes before tightening.
CORRECT INCORRECT
1 2 34 5
Use to measure bolts
First slide the Glider Bracket onto the ⁄”x2-½” Allen
Head Bolt, secondly slide the round ⁄” Aluminum
spacer onto the Allen Head Bolt, positioning the alu-
minum spacer beside the glider bracket . Once this
sequence is complete place the bolt into the pre-drilled
holes on swivel glider base.
Firmly tighten the Allen Head Bolt with the ⁄” lock
nut and place the ⁄” cap nut at the end of bolt se-
quence.
Repeat this step for the remaining glider brackets.
⁄X2-½” Allen Head Bolt
Glider Bracket
⁄” Aluminum Spacer
⁄” Lock Nut
⁄”Acorn Nut
First slide the Glider Base underneath
the Glider Chair, ensuring the correct
end of the base is pointed forward (see
photo). en li the Glider Brackets
onto the ⁄" x 2½"Allen Head Bolts
previously installed onto the Glider
Legs. Secondly Using 4- ⁄" Lock Nuts,
secure Glider Bracket onto the
Bolt securing the bracket next the ange
nut (leg side) and lock nut (outside).
Repeat this step on the remaing glider
brackets.
⁄X2-½” Allen Head Bolt
⁄” Flange Nut Nut
Glider Bracket
⁄” Lock Nut
Your Chair is Complete!
Back of Base Front of Base