Berlin Gardens Comfo Back Single User manual

1/4" x 3" Bolt
1/4" x 4 1/2" Bolt 1/4" x 3 1/2" Bolt
5/16" x 2 1/2" Bolts
5/16" Flangenuts
1/4" Flangenuts
1/4" x 3" Bolt
(Double Glider Only)
1/4" Flangenut
(Double Glider Only)
Step 1
Fasten the Arm & Leg Assembly to the Seat and
Back using the bolts and nuts specified below.
Note: The example shows a double glider. The single
glider is same except for one less bolt & nut as indicated.
Please assembly your glider on a soft surface to
avoid scratching the material.
Step 2
Turn the chair on the other side and fasten
the second Arm & Leg Assembly by repeating
step 1.
Glider Chair
Comfo Back & Cozi Back
Single & Double Counter
Height Gliders Assembly Guide
Tools Required
Hardware Included
Comfo Back Single Comfo Back Double Comfo Back Double
Cozi Back Single
Allen Wrench
(Included)
#2 Square Drive Bit
(Included) Cordless Drill
7/16" Wrench
1/2" Wrench
1/4"x3"
Bolts (x 3) 1/4"x3 1/4"
Bolts (x 4)
1/4"x3 1/2"
Bolts (x 3) 1/4"x4 1/2"
Bolts (x 3)
1/4" Flangenuts
(X 11)
5/16"x3"
Bolts (x 4)
5/16"x2 1/2"
Bolts (x 4)
5/16" Flangenuts
(X 4)
5/16" Locknuts
(X 8)
5/16" Capnuts
(X 4)
5/16" Aluminum
Spacers (X 4)
Glider Brackets
(X4)
3" Buglehead
Screws (X 10)
2" Pandeck
Screws (X 4)
1 3/4" Buglehead
Screws (X 2)

Glider Base
Step 3 Detail
Step 1
Detail A
A.
Fasten the Back Cross Piece to
a Base Side Assembly by fitting
the mortise & tenon together and
driving two - 2" Pandeck Screws
into the pocket holes as shown.
The pocket holes are to be turned inward.
B.
Position the footrest into the small
cutout in the top, front of the base side.
Fasten it using one - 3" Buglehead Screws
and one - 1 3/4" Buglehead Screws.
Note: On a double glider, the aluminum support piece
should be turned inward.
Back Cross Piece
Base Side Assembly
Two - 2" Pandeck Screws
Step 2
Repeat Step 1 (above) to attach
the second Base Side Assembly.
Step 3
Fasten both Top Cross Pieces
by driving eight - 3" Buglhead Screws
through the countersink holes in the Base
Side Assemblies and into the predrilled
holes in the ends of the Top Cross Pieces.
Top Cross Pieces
Eight - 3" Buglehead Screw
DETAIL B
3" Buglehead Screw
1 3/4" Buglehead Screw

Step 6 Detail
Step 5 Detail
Step 4 Detail
Step 4
Attach the four Glider Stops to the Base
using four - 1/4" x 3 1/4" Bolts and four -
1/4" Flangenuts.
Insert the bolts through the Glider Stops
and into the predrilled holes in the base.
Be sure to firmly fasten.
1/4" x 3 1/4" Bolts
Glider Stops
1/4" Flangenuts
Step 5
Install the Glider Brackets
using following sequence.
First slide the Glider Bracket
onto the 5/16" x 3" Bolt.
Secondly slide the round
5/16" Aluminum Spacer onto
the bolt, positioning it beside
the glider bracket. Insert the
bolt into the predrilled holes
in the glider base.
Firmly tighten with the 5/16"
Lock Nut and place a 5/16"
Cap Nut at the end of the
bolt sequence.
Repeat this step for all four
glider brackets.
5/16" x 3" Bolt
Aluminum Spacer
5/16" Lock Nut
5/16" Cap Nut
Glider Bracket
Step 6
Slide the Glider Base
Assembly underneath the
Glider Chair ensuring
that the footrest is
forward. Lift chair until
you can slide the Glider
Brackets onto the
5/16" x 2 1/2" Bolts
that are installed in the
lower part of the legs.
Using four - 5/16" Locknuts,
secure the brackets onto
the bolts and against the
flangenuts that were already
installed. Repeat this process
for each of the four
glider brackets.
5/16" Flangenut
Glider Bracket
5/16" Locknut
5/16" x 2 1/2" Bolt