berlinger Fridge-tag Ultra Low User manual

3
3
3
yyy_ ydd_
051
0 320
max.
°C
Int.Sensor
External sensor
Fridge-tag
State of delivery
Packaging content Fridge-tag information
Activation of the device
Setting the date and time
Setting the calendar format
To activate the device, press the SET and the READ
buttons simultaneously for more than  sec-
onds. The following calendar format will appear:
dd.mm.yyyy.
Note: After approx.  seconds without pressing
any button of the Fridge-tag the device goes back
into sleep mode. Start from the beginning.
Press
READ to change the calendar format.
Then press SET to save the calendar format.
3
3
The READ button is used to adjust the
numbers. Each time you press the READ
button, the number in the flashing digit
will increase by .
The SET button is used to save the num-
ber. After pressing the SET button, the
next digit will start flashing.
Note: If required note the date of activation on
the back of the Fridge-tag.
Note: Once the device has been activated, it can-
not be stopped anymore.
Option 1
Setting the calendar
format to: dd.mm.yyyy
Option 2
Setting the calendar
format to: mm.dd.yyyy
You receive the Fridge-tag
in sleep mode. The display
(LCD) is blank.
Note: Place the external sensor in its
predetermined location, before activating the
device.
Profile
(alarm zones)
 days
history
Port to insert
external sensor
Temperature
status
Temperature
measured
Set button Read button Logger ID
81020201
The st digit is flashing:
Press READ until “ ”
appears as the first digit.
Press SET to save the digit.
Go on with the next digits
in the same way until date
and time is set.
3
1 2
4
6
5
QUICK INFO – SET UP
Fridge-tag Ultra Low
Placing the Fridge-tag?
See point 8
Activation completed
As soon as the last
digit of the time setting is
confirmed, the activa-
tion is completed. Now
place the Fridge-tag and
connect the device with
the external sensor.
During max.  minute
after activation no tem-
perature is displayed on
the screen.
7
Connection error?
See user manual in chapter «Learn More»
Placing the Fridge-tag
 minutes before activating the
device the external sensor must
be placed in its predetermined
location. It is recommended and
important to place the external
sensor in the centre of the freezer
(where goods are also stored)
for an optimal temperature
observation and to avoid any
incorrect measurements when
starting the device.
8
3
yyyd y__d
Placing the Fridge-tag?
See user manual in chapter «Learn More»
Correct or change settings?
See user manual in chapter «Learn More»
Fridge-tag
Support
Product
Information
User
Manual
Berlinger
Website
Learn More
For more information scan the QR code or click on
www.berlinger.com/fridge-tag-ult
Technical
Specification
81020201
051
0 320
max.
°C
Int.Sensor
-773
.
Note: Pay attention to your safety and
protection when installing the external sensor
in your freezer and follow your organization’s
instructions for proper handling at ultra-low
temperatures.

Berlinger & Co. AG
Mitteldorfstrasse 2
9608 Ganterschwil
Switzerland
Tel. [phone]
[e-mail]
www.berlinger.com
400-01269_1
8101 2026
88
1 425
°C
Int.Sensor
!
Indication of an OK display
Example of an alarm display
Indication of an alarm display
Alarm display: additional information
The alarm
symbol
The current
date and time
Upper/lower
alarm indicator
The current
temperature
The current
temperature
8101 2026
88
1 425
°C
Int.Sensor
!
8101 2026
56
1 473
°C
Int.Sensor
Press READ a second
time for additional
information.
051
0 3
2
0
max.
°C
Int.Sensor
8101 2026
56
1 473
°C
Int.Sensor
Reading the history
Temperature status
The Fridge-tag will now generate a PDF and an
ASCII report. This process can take up to  minutes.
Note: Continue repetitively pressing the READ
button to read out the details of the past  days.
Note: Press and hold the READ button again for
at least  seconds and the next alarm event will
appear on the screen.
Press
READ
once
2
1
Alarm display and confirmation options?
See user manual in chapter «Learn More»
QUICK INFO – USER GUIDE
Fridge-tag Ultra Low
Acknowledge alarm?
See user manual in chapter «Learn More»
051
0 320
max.
°C
Int.Sensor
Example of an OK display
Connect the device via
USB with your PC/MAC.
Note: Disconnect the
external sensor from
the device first.
Handle the cable of
the external sensor
with care! Prevent that
it is folded or bended.
Download reports
3
Download reports?
See user manual in chapter «Learn More»
Press and hold READ for
 seconds for the Alarm-
Super-Jump function
051
0 3
2
0
max.
°C
Int.Sensor
8101 2026
1 218
!
In measurement mode, when no alarm has been
triggered, the following information is indicated:
The OK symbol
The current date and time
In measurement mode, when an alarm has been
triggered, the following information is indicated:
Additional
warning symbol
The highest
recorded
temperature
of that day
The OK symbol
The
corresponding
flashing arrow
Press
READ
once
The time
duration out
of the preset
temperature
high limit
The date and
time of the
alarm
The alarm and the
warning symbol
The corresponding
flashing alarm
indicator
Acknowledge alarm and buzzer details?
See user manual in chapter «Learn More»
2
1
1
051
0 320
max.
°C
Int.Sensor
-773
.
051
0 320
max.
°C
Int.Sensor
-773
.
051
0 320
max.
°C
Int.Sensor
-773
.
051
0 320
max.
°C
Int.Sensor
-773
.
051
0 320
max.
°C
Int.Sensor
-773
.
proven and
well-known
quality
8101 2026
1 218
!