Bestop 29291 Manual

Installation Instructions
Seat Covers, Rear Kit
Vehicle Application:
Jeep® Wrangler Unlimited 4-Door 2018-current
Part Number 29291
P1 - 29291 Rev. A 0119 Installation Instructions - Seat Covers, Rear Kit © 2019 Bestop, Inc.
-OR-
Read and follow, precisely, all installation instructions provided when
installing this product. Failure to do so may result in a poor t, and could
place occupants of the vehicle in a potentially dangerous situation.
To reduce the risk of accidental injury: Follow all vehicle Manufacturer’s and
Bestop® safety messages, application and installation instructions.
• Do not remove seats from the vehicle to install this product.
• Fit and maintain sides of seat cover as tight to seat as possible, always
matching front to side seam of seat with similar panels and seams of seat cover.
• Remove headrest carefully to avoid damaging manufacturer’s wiring.
Assure all plugs are connected after installation of seat cover.
• Do not use and replace if seat cover becomes damaged or wear no longer
allows a tight t to seat sides.
WEAR SEAT BELTS AT ALL TIMES
Installation TimeTools
Skill Level
Safety glasses should be worn at all
times when installing this product.
WARNING
CAUTION
Installation Tips
Care & Maintenance
2 - Moderately Difcult
1 hour
Safety
Glasses
Support
We’re here to help! Go to:
https://www.bestop.com
and click on Need Help?
https://www.bestop.com/video-library
Your seat covers are machine washable. Wash separately in COLD water with
¼ of normal amount of soap. Hang dry.

P2 - 29291 Rev. A 0119 Installation Instructions - Seat Covers, Rear Kit © 2019 Bestop, Inc.
Installation Instructions
Seat Covers, Rear Kit
Vehicle Application:
Jeep® Wrangler Unlimited 4-Door 2018-current
Part Number 29291
Parts List
- Required parts for installation - Page number in Installation Guide
Sections 1 & 2 Seatback Covers; Seat Bottom Covers
Sections 3 to 5 Center Armrest Console Cover; Headrest Covers
Pages 4 to 6 of Guide
Pages 7 to 9 of Guide
Large Seatback Cover
Qty. 1
Center Armrest Console Cover
Qty. 1
Headrest Covers
Qty. 2 - Large
Qty. 1 - Small
Small Seatback Cover
Qty. 1
Large Seat Bottom Cover
Qty. 1
Small Seat Bottom Cover
Qty. 1

P3 -29291 Rev. A 0119 Installation Instructions - Seat Covers, Rear Kit © 2019 Bestop, Inc.
Page 3
Step 1
Section 1 Remove the Center Console Headrest
Step 1
Step 1
Remove the center console headrest. Lift
the headrest until it stops. Then:
1 Squeeze the headrest release buttons
on the headrest supports. Release one post
and then the other.
2Lift the headrest to remove it from the
headrest supports.
21

P4 -29291 Rev. A 0119 Installation Instructions - Seat Covers, Rear Kit © 2019 Bestop, Inc.
Page 4
2
3
2
Step 1 Step 2
Step 2
Section 2 Install Seatback Covers
Step 1
1 Unzip the back of the Small Seatback
Cover.
2Slip the seat cover over the headrest
and over the small seatback.
1 Unzip the back of the Large Seatback
Cover.
2Slip the seat cover over the headrest,
under the seatbelt, and over the large
seatback.
3Tilt the seatback about halfway forward
to allow the cover to slip completely over
the seatback.
Unzip both seat covers
before installing.
OR
1

P5 -29291 Rev. A 0119 Installation Instructions - Seat Covers, Rear Kit © 2019 Bestop, Inc.
Page 5
Step 1 Step 2
Section 2 Install Seatback Covers (cont.)
Tuck flap behind
seatback cover
below armrest
Step 1
Step 2
Flip down the Center Armrest Console.
Feed the long ap on the Large Seatback
Cover behind the console, so that the end
of the ap with the Hook-&-Loop strip
comes out below the console.
Flip the Center Armrest Console back up.
Tuck the end of the long ap, with the
Hook-&-Loop strip, behind the seatback
fabric just below the console.
Firmly attach the Hook-&-Loop strip to the
inside of the seatback fabric.

P6 -29291 Rev. A 0119 Installation Instructions - Seat Covers, Rear Kit © 2019 Bestop, Inc.
Page 6
3
OR
2
1
Step 1 Step 2
Section 2 Install Seatback Covers (cont.)
Step 2
Step 1
Tilt the seatback forward about halfway,
which will provide a space between the
seatback and the seat bottom.
With the seatback tilted forward, tuck the
ap at the bottom of the Large Seatback
Cover between the seatback and the seat
bottom.
Repeat this procedure on the Small
Seatback Cover.
1 Tuck the aps between the headrest posts
underneath the seat covers at the rear.
Make sure that the seatback release latches
are accessible on both seats.
2 Zip both the Large and Small Seatback
Covers closed. Make sure that the seat belt is
not caught in the cover and operates smoothly.
3 Tuck the aps coming between the seat-
backs and seat bottoms under the bottom of
each Seatback Cover. Snug the t by pulling
down on the Seatback Cover while lifting up
on the aps and pushing the hook-&-loop
strips rmly together.

P7 -29291 Rev. A 0119 Installation Instructions - Seat Covers, Rear Kit © 2019 Bestop, Inc.
Page 7
Step 1 Step 2
2
1
Section 3 Install Center Armrest Console Cover
Center Armrest
Console Cover
Qty. 1
Step 1
Step 2
1 Flip the center console down.
2Slide the Center Console Armrest
Cover over the console. Wrap the fabric ap around the armrest
console. Tuck the ap underneath the
Armrest Cover.
Attach the Hook-&-Loop strip to the inside
of the console cover fabric.
Flip the Center Armrest Console back up.

P8 -29291 Rev. A 0119 Installation Instructions - Seat Covers, Rear Kit © 2019 Bestop, Inc.
Page 8
1
1
Section 4 Install Seat Bottom Covers
Step 2
Step 1
Step 1
Step 2
1 Slip the Small Seat Bottom Cover over the
small seat bottom.
2 Tilt the seatback halfway forward, to open
a space between the seatback and the seat
bottom.
3 Attach the Hook-&-Loop fabric tabs on the
inside of the Seat Cover to the carpet.
4 Feed the ap between the seatback and
seat bottom, and attach the Hook-&-Loop
fabric to the carpet.
1 Slip the Large Seat Bottom Cover over the
large seat bottom.
Follow 2 3 and 4 from Step 1 doing all
the same things as you did on the Small Seat
Bottom Cover.
2
4
3

P9 -29291 Rev. A 0119 Installation Instructions - Seat Covers, Rear Kit © 2019 Bestop, Inc.
Page 9
Step 1 Step 2
Wrap the Headrest Covers over the main
headrests, making sure that the crossed elastic
edging and internal label are at the back of each
headrest.
Place center armrest console headrest posts
through the holes in the center headrest cover,
from the inside. Wrap the cover over the
center headrest.
Adjust all seams for a smoother appearance.
Section 5 Install Headrest Covers; Replace Center Headrest
Step 1 Step 2
Replace the center armrest console
headrest:
1 Squeeze the headrest release buttons
on the headrest supports.
2Insert the headrest posts into the
headrest supports in the top of the center
armrest console.
21