Bestop 51252 User manual

51252 pg 1 0410 Rev. B
TM
® Inc.
Installation Tips
Before you begin installing the Rotary Paddle
Handle Latch assembly, read all instructions
thoroughly. After completion of the project,
please keep the instruction for future reference.
This product is designed primarily to enhance the appear-
ance of the vehicle and to shield the occupants from ordinary
weather conditions. Do not rely in any way on the compo-
nents of this product to contain occupants within the vehicle,
or to protect against injury or death in the event of an
accident. This product will not protect the occupants from
falling objects. Never operate vehicle in excess of
manufacturer’s specifications.
WEAR SEAT BELTS AT ALL TIMES
Read and follow, precisely, all installation instructions pro-
vided when installing this product. Failure to do so may result
in poor fit and could place occupants of the vehicle in a
potentially dangerous situation.
WARNING
Rotary Paddle Handle Latch Kit
Installation Instructions
For: Wrangler (1997-current) Part Number: 51252

51252 pg 2
0410 Rev. B
Parts List and Hardware Identification
Tools Needed
Phillips Head Screwdriver
3/8" Wrench
#10-24 Truss Head Machine Screw - Black,
Qty - 8, Part Number 195.92
#10-24 Locknut, Qty - 8,
Part Number 195.93
If your vehicle does not have the latch pin assembly illustrated here,
you have an incorrect part for your vehicle. Please call the 1-800
number before attempting installation.
Latches - Rotary Paddle Handle -
Rt., Qty - 1, 454.42
Lt., Qty - 1, 454.43
Special Note: The Rotary Latch Paddle Handle will only latch on
the automobile manufacturer's original equipment steel latch pin
located on the vehicle. Do Not adjust or remove this part.
STOP
Spacer Kit , Qty - 1, Part Number 287.59

51252 pg 3 0410 Rev. B
WARNING
CAUTION: DO NOT attempt to adjust the Original Equipment Latch Pin (illustrated on Page 2). Doing so could result
in damage to the pin.
Step Two
Remove the plastic caps from the upper door pins and from the Lower Door Hinge Pins. Locate the pre-cut "X" in the
lower door panel where the Paddle Handle will fit into the mounting plate on the door frame. Fold the pre-cut fabric
back and insert the Paddle Handle into the mounting plate so that the latch mechanism is inside of the vehicle and the
Rotary Latch Mechanism is toward the rear of the door. Align the four holes in the Paddle Handle Assembly with the
four holes in the mounting plate. Use a pointed tool to punch four holes in the fabric to match the holes in the Paddle
Handle and the mounting plate. Insert four #10-24 Truss Head Machine Screws from the outside and secure them
with #10-24 Locknuts. Do not tighten the screws until all four are in place. Important: You should check alignment of
the Paddle Handle to the steel latch pin before tightening the screws. If out of alignment, align and retighten the
screws securely. Trim the excess fabric around the Paddle Handle. Repeat for both lower doors.
It is important that the Paddle Handle must align correctly with the automobile
manufacturer’s original equipment steel latch pin located on the vehicle. Failure to
properly install the paddle handle may result in the door accidently opening.
IMPROPER CLOSURE COULD RESULT IN SERIOUS INJURY OR DEATH TO THE
OCCUPANTS. WEAR SEAT BELTS AT ALL TIMES. DRIVE CAREFULLY.
Step One
Remove the old Paddle Handle Latch assembly from the lower half door.
Rear of Door
Rotary Latch
Mechanism
Inside of Door
Paddle Handle Assembly
#10-24 Truss Head Machine
Screws and #10-24 Locknuts Frame Integrated Handle
Mounting Plate
Note: If the lower door pivot does not provide enough adjustability for correct latch adjustment (the door does not latch properly), follow
the instructions in the enclosed spacer kit.

51252 pg 4
0410 Rev. B
LIMITED WARRANTY
We warrant our product to be free from defects in material and workmanship, for the terms specified below, provided there has been normal use and proper
maintenance. This warranty applies to the original purchaser only. All remedies under this warranty are limited to the repair or replacement of any item or items
found by the factory to be defective within the time period specified.
If you have a warranty claim, first you must call our factory at the number below for instructions. You must retain proof of purchase and submit a copy with any items
returned for warranty work. Upon completion of warranty work, if any, we will return the repaired or replaced item or items to you freight prepaid. Damage to our
products caused by accidents, fire, vandalism, negligence, misinstallation, misuse, Acts of God, or by defective parts not manufactured by us, is not covered under
this warranty.
THE WARRANTY TIME PERIOD IS AS FOLLOWS: ALL “SOFT GOODS” MANUFACTURED BY OUR COMPANY (USING PRIMARILY VINYLS, PLASTICS, AND/
OR FOAM): ONE YEAR FROM DATE OF PURCHASE.
ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE CREATED HEREBY ARE LIMITED IN DURATION
TO THE SAME DURATION AND SCOPE AS THE EXPRESS WRITTEN WARRANTY. OUR COMPANY SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGE.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For further information or request for warranty work, please contact: Bestop Inc.
Customer Service
[phone]
[phone]