Bestop 42503 User manual

INSTALLATION TIME SKILL LEVEL
2 Hours 2 - Moderately Easy
TOOLS
Vehicle Application
•Jeep Wrangler
2011 - Current
Part Number: 42503
10mm,13mm10mm,13mm 4mm T-30, T-40
www.Bestop.com - We’re here to help! Visit our web site and click on “Ask a Question”. Click here for more Jeep Accessories by Bestop.
Installation Instructions
Pet Barrier
This product is designed primarily to enhance the appearance of the vehicle. Do not rely in any way on the components of this product to
protect against injury or death in the event of an accident. Never operate the vehicle in excess of manuracturer’s specifications.
WEAR SEAT BELTS AT ALL TIMES
Read and follow, precisely, all installation instructions provided when installing product. Failure to do so may result in a poor fit and could place occupants
of the vehicle in a potentially dangerous situation.

Pet Barrier – Installation Instructions
Rev. F 0114 42503 pg. 2
M8 Lock Nut (Nyloc
Nut), Qty - 2
Parts List and Hardware Identification
M6 Lock Nut,
Qty - 8
M6 Washer,
Qty - 18
M8 Washer,
Qty - 4
Soft Top Only
M6 Spring
Washer,
Qty - 2
Upper Partition,
Qty - 1
Lower Partition,
Qty - 1
Use a T-30 torx to remove the screw from the outside
plastic seat rail cover. Discard the screw. Repeat on
both sides of the vehicle.
For easiest installation, remove the rear
seat prior to installing the Pet Barrier.
Loosen Plastic Seat Rail Cover
M6 x 35mm Button Head Screw, Qty - 4
M6 x 16mm Button Head Screw, Qty - 2
M6 x 25mm Button Head Screw, Qty - 6
M8 x 35mm Hex Bolt, Qty - 2
M6 x 15 Thumbscrew, Part
Number 495.60, Qty - 4
M6 x 20 Thumbscrew, Part
Number 495.61, Qty - 2
Left Middle
Bracket, Qty - 1 Right Middle Bracket, Qty - 1
Upper Connecting
Bracket, Qty - 2
Upper Mounting
Bracket, Qty - 2
Lower Mounting
Bracket, Qty - 2
Lower Connecting
Bracket, Qty - 2
Passenger Side Shown
Seat
Seat Rail Cover

Pet Barrier – Installation Instructions
Rev. F 0114 42503 pg. 3
Lift the plastic seat rail cover and slide a Lower
Connecting Bracket under the cover. Install an
M6 x 16mm Button Head Screw with an M6
Washer. Use a 4mm allen wrench to tighten.
Repeat on both sides of the vehicle.
Use an M6 x 15 Thumbscrew to mount a Lower
Mounting Bracket to the Lower Connecting Bracket.
Repeat on both sides of the vehicle.
Install Lower Connecting Brackets Install Lower Mounting Brackets
Place the Lower Partition in the vehicle from the rear.
Use the M6 x 15mm Thumbscrews to secure the
Lower Partition to the Base Brackets installed in
Step 1.
Use a T-40 Torx to remove the screw from the front
corner near the sport bar and discard it. Use an M8
x 35mm Hex Bolt to install a Middle Bracket. Repeat
on both sides of the vehicle.
Use a 13mm wrench and socket to install a Middle
Bracket in the hole near the front sport bar using
an M8 x 35mm Hex Bolt, M8 Bushing, two (2) M8
Washers and an M8 Nut. Repeat on both sides of
the vehicle.
Install Lower Partition
Install Middle Brackets Install Middle Brackets
Hard Top Soft Top
T-40 Torx
Right Middle
Bracket
M8 x 35mm
Hex Bolt
M8 Bushing
M8 Washer
M8 Washer
M8 Nut
Right Middle
Bracket
Middle
Bracket
Passenger Side Shown
Passenger Side Shown
Passenger Side Shown Base
Bracket
M6 x 15mm
Thumbscrew
Lower Connecting
Bracket
Lower Connecting
Bracket M6 x 16mm Button
Head Screw with
M6 Washer
Lower Connecting
Bracket
M6 x 15
Thumbscrew

Pet Barrier – Installation Instructions
Rev. F 0114 42503 pg. 4
Use a 4mm allen wrench and two (2) M6 x 25mm
Button Head Screws with two (2) M6 Spring Wash-
ers to secure the Lower Partition to the Middle
Brackets installed in Step 2.
Use a 10mm socket to remove the front bolt from
the outside of the sport bar.
Orient the Upper Connecting Bracket so that the
threaded insert on the bracket is toward the outside
of the vehicle.
Reuse the bolt to install the Upper Connecting
Bracket.
Secure Lower Partition to
Middle Brackets Install Upper Connecting Brackets
Lower
Partition
Middle
Bracket
M6 x 25mm Button
Head Screw with
M6 Spring Washer
Use a 4mm allen wrench and a 10mm wrench with
two (2) M6 x 25mm Button Head Screws, four (4)
M6 Washers and two (2) M6 Lock Nuts to secure
an Upper Mounting Bracket to the Upper Partition.
Do not tighten fasteners. Repeat on both sides.
Install Upper Mounting Bracket
on Upper Partition Mount Upper Partition Assembly
to Upper Connecting Bracket
Use the M6 x 20mm Thumbscrews to secure the
Upper Partition to the Upper Connecting Brackets.
Tighten Fasteners on Upper
Mounting Brackets
Use a 4mm allen wrench and 10mm wrench to tight-
en the fasteners on the Upper Mounting Brackets.
Upper Mounting
Bracket
Upper
Partition
M6 x 25mm Button
Head Screws
M6 Washers and
M6 Lock Nuts
Upper Connecting
Bracket M6 x 20mm
Thumbscrew

Pet Barrier – Installation Instructions
Rev. F 0114 42503 pg. 5
Reinstall the rear seat if you removed it prior to
beginning the installation.
Reinstall Rear Seat
Use a 4mm allen wrench and a
10mm wrench with four (4) M6
x 35mm Button Head Screws,
eight (8) M6 Washers and four
(4) M6 Lock Nuts to secure the
Upper Partition to the Lower
Partition.
Secure Upper Partition to Lower
Partition
M6 x 35mm Button
Head Screw
M6 Washers
M6 Lock Nut
Upper Partition
Lower Partition