Bestop 52406 User manual

Installation Instructions

Retractable Sunshade

Vehicle Application: Jeep® Wrangler JK 2 Door and 4 Door

With Sunrider for Hardtop 2007-2018

Part Number 52406

Before you begin installing your new Retractable Sunshade,

please read all the instructions thoroughly, and watch the Bestop

Installation video. (See Support section on this page)

Do not rely in any way on the components of this product to protect

against injury or death in the event of an accident. Never operate the vehicle in excess of

manufacturer’s specications.

Read and follow, precisely, all installation instructions provided when installing this product.

Failure to do so may result in a poor t and could place occupants of the vehicle in a potentially

dangerous situation.

WEAR SEAT BELTS AT ALL TIMES

Safety glasses should be worn at all

times when installing this product.

WARNING

Installation Tips

SupportInstallation TimeTools

Skill Level

We’re here to help!

Go to www.Bestop.com and

click on “Contact Us”

1 - Easy

30 minutes

Safety

Glasses

Installation Instructions

Retractable Sunshade

Vehicle Application: Jeep® Wrangler JK 2 Door and 4 Door

With Sunrider for Hardtop 2007-2018

Part Number 52406

Installation Instructions

Supertop NX Twill

Vehicle Application:

Jeep Wrangler Unlimited

2007-current

Part Number 54823

Installation Instructions

Retractable Sunshade

Parts List

- Required parts for installation - Page number in Installation Guide

Vehicle Application: Jeep® Wrangler JK 2 Door and 4 Door

With Sunrider for Hardtop 2007-2018

Part Number 52406

All Sections Hardware Multiple Pages

Retractable Sunshade

Qty. 1 Mesh Blockout Panel

Qty. 1 Hook & Loop Strips

Qty. 3

Page 4

Section 1 Release Header Latches and Open the Sunrider - 2-Door and 4-Door

Step 1 2-Door & 4-Door 2-Door & 4-DoorStep 2

2-Door & 4-Door Jeeps:

Release the windshield header

latches. 2-Door & 4-Door Jeeps:

Open the Sunrider by lifting the

Header Assembly away from the

windshield and pivoting it toward the

rear of the Jeep.

Step 1

Step 2

Page 5

Section 2 Remove Rear Mushroom Knobs & Attach Sunshade: 2-Door and 4-door

Step 1 Step 2

2-Door and 4-Door Jeeps:

Remove the two rear mushroom

knobs. Leave the two front knobs in

place.

2-Door and 4-Door Jeeps:

Place the Retractable Sunshade on

top of the Door Rails, aligning the

holes in the brackets to the holes in

the Door Rails.

Secure the Retractable Shade in

place: replace the Mushroom knobs

that you removed earlier, being sure

to tighten the knobs rmly.

Step 1 Step 2

2-Door & 4-Door 2-Door & 4-Door

Page 6

Section 3 Attach Mesh Blockout Panel

Step 1 Step 2

Parts

2-Door and 4-Door Jeeps:

Locate the Mesh Blockout Panel. The

mesh panel will be used to cover the

gap between the Retractable Shade

and the hardtop.

Make sure that when you place the

mesh panel over the gap, that the

Hook & Loop tabs have the Loop side

facing down.

Step 1

2-Door & 4-Door 2-Door & 4-Door

Mesh Blackout Panel

with Hook-&-Loop tabs

2-Door and 4-Door Jeeps:

Feed the long elastic loops from

front-to-back between the hardtop

and the soundbar.

Grasp each long loop at the rear of

the soundbar, wrap it around the

soundbar, and secure it by looping it

around the toggle at the end of the

short elastic loop.

See Detail.

Step 2

View from inside Jeep

Loop side of Hook & Loop

tabs must face down

Detail

Wrap each long

loop around the

toggle at the end

of each short loop.

Page 7

Section 3 Attach Mesh Blockout Panel (cont.)

Step 3 Step 4

2-Door and 4-Door Jeeps:

Place the three (3) Hook & Loop strips

onto the three tabs on the front edge

of the Mesh Panel.

Do not remove the adhesive liners

yet.

2-Door and 4-Door Jeeps:

Wrap each long elastic loop at the

right and left ends of the Retractable

Shade around the mushroom knob on

each side, securing it by wrapping the

loop over the toggle at the end of the

shorter loop, the same as you did with

the loops wrapped around the sound

bar.

Step 4

Step 3

2-Door & 4-Door 2-Door & 4-Door

Place Hook & Loop

strips on the the 3 tabs.

Do not peel off the

adhesive liner yet.

Page 8

Section 3 Attach Mesh Blockout Panel (cont.); Using the Retractable Sunshade

Step 5

2-Door and 4-Door Jeeps:

1Peel the adhesive liner from the center Hook

& Loop strip, and adhere to the center of the

Retractable Shade, in the shallow channel on the

back side of the Retractable Shade.

2and 3Peel the adhesive liner from the

left and right Hook & Loop strips, and adhere

them to the Retractable Shade, so that the Mesh

Panel is free of wrinkles.

NOTE: Hook& Loop adhesive takes a couple of

hours to achieve full strength. For best results,

clean all surfaces with denatured alcohol before

adhering strips.

Step 5

2-Door & 4-Door

2-Door and 4-DoorStep 6

With the Retractable Sunshade rmly

secured in place, the shade can now

be deployed. Pull the shade forward

using the pull tab, and secure it to the

windshield loops using the hooks, one

on each side of the shade.

See Detail.

Step 6

Detail

Installation Instructions

Retractable Sunshade

Vehicle Application: Jeep® Wrangler JK 2 Door and 4 Door

With Sunrider for Hardtop 2007-2018

Part Number 52406

Care and Maintenance of your Bestop Product

Fabric: The fabric should be washed often using soap, warm water and a soft bristle brush. Rinse with clear water to remove all traces of soap. Bestop recommends using Bestop Cleaner

(part no. 11201-00) and Bestop Twill Protectant (part no. 11207-00) which are specially formulated to provide a total cleaning and protection system

Windows: Keep windows clean to avoid scratching. DO NOT use a brush on the windows! Wash with a water-soaked cloth or sponge and a mild dishwashing detergent. Bestop recommends

Bestop Vinyl Window Cleaner (part no. 11203-00), which safely cleans and protects vinyl windows and helps prevent UV damage. NEVER WIPE THE WINDOWS WHEN THEY ARE DRY. Be

careful when cleaning snow or frost from the vinyl windows since they are easily scratched and may crack at low temperatures. DO NOT roll the sides or rear window in cold weather. The

windows become stiff and will crack. Cracks caused by misuse in cold temperatures are not covered under warranty.

Zippers: Keeping zippers cleaned and lubricated with Bestop’s Zipper Cleaner (part no. 11206-00) will help prevent damage and keep the zippers in smooth

working condition. If a zipper opens behind the slider, the slider may have been spread apart. This problem can usually be repaired by

using an ordinary pair of pliers to bring the sides back into parallel. Return slider to the end of the zipper in the normal Open position.

again. Repeat this procedure until the zipper operates correctly.

Water: Seeping through at the seams may be stopped by applying 3-M Scotchgard® on the inside of the seams. Rips in the fabric may be repaired with

Bondex® iron on patches. Iron the patches to the Inside of the top, carefully following the Bondex® instructions.

Snaps: Keep snaps cleaned and lubricated with silicone to help prevent snaps from sticking to the studs. If a snap does become stuck to a stud, use a

screwdriver and GENTLY pry apart to prevent permanent damage to the snap or the top fabric.

Damaged Slider -

Jaws Spread Apart

(sometimes broken)

Normal Slider -

Jaws Parallel

Installation Instructions

Retractable Sunshade

Vehicle Application: Jeep® Wrangler JK 2 Door and 4 Door

With Sunrider for Hardtop 2007-2018

Part Number 52406

Soin et entretien de votre produit Bestop

Tissu : Bestop

Cleaner (pièce no 11201-00) et Bestop Twill Protectant (pièce no 11207-00) which qui sont spécialement formulés pour fournir un système complet de nettoyage et de protection.

Vitres : Maintenir les vitres propres pour éviter de les égratigner. NE PAS utiliser une brosse sur les fenêtres. Laver avec un chiffon ou une éponge imbibée d’eau et d’un savon à vaisselle doux. Bestop recom-

mande Bestop Vinyl Window Cleaner (no de pièce 11203-00), lequel nettoie et protégé les vitres de vinyle et aide à prévenir les dommages causés par les UV. NE JAMAIS ESSUYER LES VITRES ALORS

Fermetures à glissière : 1206-00)

de Bestop aidera à protéger des dommages et maintiendra les fermetures à glissière en bon état de fonctionnement. Si une fermeture à glissière

ouvre derrière la glissière, la glissière peut avoir été forcée au point de s’ouvrir. Le problème peut habituellement être réparé en utilisant des pinces

ordinaires pour remettre les côtés parallèles. Remettre la glissière au bout de la fermeture à glissière, dans la position Ouverte normale. Serrer

ment à l’aide des pinces et essayer la fermeture à glissière de nouveau. Répéter le processus jusqu’à ce que la fermeture à glissière fonctionne

correctement.

Eau :

peuvent être réparées grâce aux pièces thermocollantes Bondex®. Fixer les pièces thermocollantes à l’aide d’un fer à repasser sur l’intérieur du toit, en suivant

soigneusement les instructions de Bondex®.

Boutons pression : Maintenir les boutons pression propres à l’aide de silicone pour empêcher les boutons pression de coller aux rivets. Si un bouton pression

reste collé à un rivet, utiliser un tournevis et appliquer une F

Glissière normale -

Mâchoires parallèles

Glissière endommagée -

Mâchoires écartées

(parfois brisées)

Cuidado y mantenimiento de su producto Bestop

Su producto Bestop está hecho con materiales de la más alta calidad. Para mantener su aspecto nuevo y alargar su vida útil al máximo posible, necesitará limpieza y mantenimiento periódicos.

Tela: debe lavar la tela con frecuencia usando jabón, agua tibia y un cepillo de cerdas suaves. Enjuague con agua limpia para eliminar todos los residuos de jabón. Bestop recomienda usar Bestop Cleaner

(núm. de parte 11201-00) y BestopTwill Protectant (núm. de parte 11207-00) que están formulados especialmente para proporcionar un sistema de limpieza y protección total.

Ventanas: mantenga las ventanas abiertas para evitar que se rayen. ¡NO use cepillo para lavar las ventanas! Lave con un paño o esponja empapado de agua y un detergente suave para lavar platos. Bestop

recomienda usar el limpiador de ventanas de vinilo Bestop (número de parte 11203-00), que limpia de manera segura y protege las ventanas de vinilo, además de ayudar a prevenir daños causados por los

rayos UV. NUNCA LIMPIE LAS VENTANAS CUANDO ESTÉN SECAS. Tenga cuidado cuando limpie la nieve o escarcha de las ventanas de vinilo, ya que se rayan con facilidad y pueden agrietarse a temper-

aturas bajas. NO baje las ventanas laterales o la ventana de la parte posterior cuando haga frío. Las ventanas pueden ponerse rígidas y agrietarse. Esta garantía no cubre las grietas causadas por mal uso en

temperaturas frías.

Cremalleras: conserve las cremalleras limpias y lubricadas con el limpiador de cremalleras Bestop (número de parte 11206-00), que ayuda a pre-

venir daños y mantiene las cremalleras en óptimas condiciones de funcionamiento. Si la cremallera se abre detrás de la corredera, es posible que

las mordazas de la corredera se hayan separado. Por lo general, este problema se repara fácilmente con un par de pinzas comunes para volver a

poner los lados en paralelo. Regrese la corredera al extremo de la cremallera en la posición abierta normal. Apriete un poco al principio y pruebe

hasta que la cremallera funcione correctamente.

Agua:

repararse con parches Bondex® que se aplican con plancha. Planche los parches en el interior de la capota, siguiendo con cuidado las instrucciones de Bon-

dex®.

Broches: conserve los broches limpios y lubricados con silicona para evitar que se peguen a los corchetes de encaje. Si un broche se queda pegado a un cor-