Betta VEUE User manual

N MANUAL
m Up
VEUE | WIRE GUIDE
INSTALLATION MANUAL

SECTION A | TOOLS AND ADDITIONAL ITEMS REQUIRED
3
SECTION C | TROUBLESHOOTING
18
CONTENTS
PART A –TOOLS REQUIRED ............................................................................................................................................ 3
PART B –ADDITIONAL ITEMS REQUIRED (NOT SUPPLIED).............................................................................................. 3
PARTC–BLIND ITEMS REQUIRED................................................................................................................................... 3
PART D –BLIND ITEMS REQUIRED.................................................................................................................................. 4
PART A –PREPARING INSTALLATION SPACE................................................................................................................... 5
PART B –BOX INSTALLATION.......................................................................................................................................... 6
PART C –OPEN BRACKET INSTALLATION ........................................................................................................................ 6
PART D –BLIND INSTALLATION....................................................................................................................................... 7
PART E –TENSION GUIDELINES .................................................................................................................................... 13
SECTION B | INSTALLATION
5

SECTION A | TOOLS AND ADDITIONAL ITEMS REQUIRED
Page. 3
PART A –TOOLS REQUIRED
•Saw
•Drill
•Screw Driver –Philips Head & Flat Head
•Jaw Pliers
•Allen Key Set
•Mallet
•Scissors
•Measuring Tape
•Pencil
PART B –ADDITIONAL ITEMS REQUIRED (NOT SUPPLIED)
To assemble an Veue | Wire Guide, the following non-stocked items are required:
•Fixings for Box/Open Brackets/Hardware (ensure appropriate fixings are used to suit application)
•Trims to conceal packing (if required)
PART C –BLIND ITEMS REQUIRED
BOX OPEN BRACKETS
or
NOTE: Store clip until required (can be left in adaptor as shown)
BLIND

SECTION A | TOOLS AND ADDITIONAL ITEMS REQUIRED
PART D –BLIND ITEMS REQUIRED
WIRE GUIDE AND FIXING HARDWARE
OPTION 1 –Hook Terminal
STRAP DOWN HARDWARE
SS SADDLE &SWIVEL EYE SHACKLE DIAMOND EYE PAD
Page. 4

SECTION B | INSTALLATION
PART A –PREPARING INSTALLATION
STEP 1. - CHECK FOR OBSTRUCTIONS
Check for any obstructions that may interfere in installation.
STEP 2. - CHECK VERTICAL & HORIZONTAL INSTALLATION DIMENSIONS
VERTICAL DIMENSIONS
HORIZONTAL DIMENSIONS
Check if top of installation space is level.
•If H1 ≠H2, corrective actions may need to be considered
prior to installation
If W2 ≥W1, W1=Blind Width
(proceed to Part B)
If W2 < W1, by a value of:
0-20mm, Proceed to Part B (W1 = Blind Width)
20+, Consider corrective action to square installation space
Page. 5

SECTION B | INSTALLATION
PART B –BOX INSTALLATION
STEP 1 –INSTALL BOX TO WALL/CEILING
FACE FIX
SIDE FIX TOP FIX
NOTE:
Use appropriate fixings to suit application. Ensure Box is Aligned and Level. Ensure 2
fasteners are used per side.
PART D –OPEN BRACKET INSTALLATION
STEP 1 –INSTALL BRACKETS TO WALL/CEILING
FACE FIX SIDE FIX TOP FIX
NOTE:
Use appropriate fixings to suit application. Ensure 2 fasteners are used per side. Ensure
brackets are aligned and level.
Measure brackets end to end to confirm measurement is correct.
Page. 6

SECTION B | INSTALLATION
PART D –BLIND INSTALLATION
STEP 1 –MARK &SECURE WIRE GUIDE FIXINGS AND TRIM WIRE TO SUIT
Wire Centres
BOX
19mm
OPEN
18mm
NOTE: Cut wire to assist installation (ensure wire is not cut too short, excess can be trimmed later)
FLOOR FIX FACE/SIDE FIX FLOOR FIX
(OPTIONAL FOR SECURING TO MASONRY)
NOTE: Ensure fasteners suit substrate application Max
fastener size #10, Max Dynabolt Size: M6
Page. 7

SECTION B | INSTALLATION
PART D –BLIND INSTALLATION
STEP 2 –INSERT SPRING ONTO WIRE
STEP 3 –ATTACH WIRE AND SPRING TO BRACKET
OPTION 1 –HOOK TERMINAL
NOTE: Tube hardware not shown for clarity of wire installation
Page. 8

SECTION B | INSTALLATION
STEP 4 –INSERT BLIND INTO BOX
STEP 5 –INSERT WIRE THROUGH WEIGHT BAR
END CAP FLOATS
NOTE:
•Insert control end first
•Ensure blind is secure
PART D –BLIND INSTALLATION
STEP 6 –INSERT CLIP INTO IDLER ADAPTER
IDLER END
Page. 12
Page. 9
Ensure pin is clipped in securely
Tighten the Screw

SECTION B | INSTALLATION
PART D –BLIND INSTALLATION
STEP 7 –FEED THROUGH MOTOR CABLE (FOR MOTOR ONLY)
STEP 8 –RUN BLIND DOWN + CENTRE
Page. 10