BOMBAY 1853405 User manual

1853405
Medford Magazine Rack
Page 1 of 5 R-4-21-04
Parts and Hardware List
A. Left Assembly 1 pc
B. Right Assembly 1 pc
C. Front Assembly 1 pc
D. Back Assembly 1 pc
E. Bottom Assembly 1 pc
F. Feet 4 pcs
G. Magazine Separators 2 pcs
H. Drawer 1 pc
I. Drawer Stoppers 2 pcs
J. Connecting Bolts 4 pcs
K. Eccentric Cams 4 pcs
L. Plastic Covers 4 pcs
M. Allen Head Bolts 4 pcs
N. Flat Washers 4 pcs
O. Lock Washers 4 pcs
P. Allen Head Wrench 1 pc
Q. Flat Head Screwdriver 1 pc
R. Phillips Head Screwdriver 1 pc
∗ Please make sure that you have all the parts and hardware indicated above before you begin assembly of this item.
∗ Use the hardware illustration to determine correct piece and size.
∗ This item should be assembled on a soft surface to prevent scratching the finish during assembly.
∗ This item may require periodic tightening.

1853405
Medford Magazine Rack
Page 2 of 5 R-4-21-04
Hardware Illustration
I. Drawer Stopper J. Connecting Bolt
K. Eccentric Cam L. Plastic Cover
M. Allen Head Bolt
N
. Flat Washe
r
O. Lock Washer

1853405
Medford Magazine Rack
Page 3 of 5 R-4-21-04
Attach Feet and Front & Back Assemblies
A. Left Assembly 1 pc J. Connecting Bolts 4 pcs
B. Right Assembly 1 pc K. Eccentric Cams 4 pcs
C. Front Assembly 1 pc L. Plastic Covers 4 pcs
D. Back Assembly 1 pc Q. Flat Head Screwdriver 1 pc
F. Feet 4 pcs R. Phillips Head Screwdriver 1 pc
1. Attach Feet (F) Align the exposed threads of the Feet (F) with pre-threaded holes in the Left & Right Assemblies
(A, B). Tighten by turing in clockwise direction. See Illustration #1.
2. Attach Connecting Bolts (J) Place the Left & Right Assemblies (A, B) on a soft surface. Align the exposed
threads on the Connecting Bolts (J) with the pre-drilled holes in the top of Left & Right Assemblies (A, B). Tighten
by turning in a clockwise direction using the Flat Head Screwdriver (Q). See Illustration # 1.
3. Attach Front & Back Assemblies (C, D) Align the pre-drilled holes in the top ends of Front & Back Assemblies
(C, D) with the Connecting Bolts (J). Make sure the dowels of bottom stretchers in the Front & Back Assemblies
(C, D) align with the pre-drilled holes in the bottom of Left & Right Assemblies (C, D). Insert the Eccentric Cams
(K) into the pre-drilled holes of Front & Back Assemblies (C, D). Make sure the groove in the Eccentric Cams (K)
faces out and the arrow points towards the Connecting Bolts (J). Use the Phillips Head Screwdriver (R) to adjust
the Eccentric Cams (K) and to lock the inserted Connecting Bolts (J) in place by turning in a clockwise direction.
Cover the Eccentric Cams (K) with Plastic Covers (L). See Illustration # 2.
Attach Bottom Assembly
Illustration # 1
Illustration # 2

1853405
Medford Magazine Rack
Page 4 of 5 R-4-21-04
4. Attach Bottom Assembly (E) Place the item upside down on a soft surface. Put the Bottom Assembly (E) upside
down on the bottom of item. Make sure the part sticking out of Bottom Assembly (E) faces front. Adjust and align
the pre-drilled holes in end of the Bottom Assembly (E) with the pre-threaded holes in the Left & Right Assemblies
(A, B). Secure with Allen Head Bolts (M), Lock Washers (O) and Flat Washers (N) using Allen Head Wrench (P).
See Illustration # 3.
A. Left Assembly 1 pc N. Flat Washers 4 pcs
B. Right Assembly 1 pc O. Lock Washers 4 pcs
E. Bottom Assembly 1 pc P. Allen Head Wrench 1 pc
M. Allen Head Bolts 4 pcs
Illustration # 3

1853405
Medford Magazine Rack
Page 5 of 5 R-4-21-04
Attach Magazine Separators & Drawer
5. Attach Magazine Separators (G) & Drawer (H) Put item upright. Insert the Magazine Separators (G) into the
pre-cut grooves in the Left & Right Assemblies (A, B). Make sure the arches are facing up. Partially insert Drawer
(H) into the rack. Insert the Drawer Stoppers (I) into the pre-drilled holes in the side panels of Drawer (H). See
Illustrations # 4 & 5.
A. Left Assembly 1 pc H. Drawer 1 pc
B. Right Assembly 1 pc I. Drawer Stoppers 2 pcs
G. Magazine Separators 2 pcs
Illustration # 4 Illustration # 5