SMITH SYSTEM Flexline Station User manual

For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
You may also place your order online at
www.smithsystem.com
Form# 179844 04/2013
Flexline Station
Assembly Instructions

For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
You may also place your order online at
www.smithsystem.com
Form# 179844 04/2013
Hardware and Components
Replacement Hardware Packs:
1. 69723-R –Flex Table Additional Hardware Pack
a. (11) 70054 –SM Screw #10x.75 HI/LO PTH
b. (3) 70088 –Screw, Button Head 8MX20MM
2. 69729-R –Flex Y-Leg Hardware Pack
a. (4) 70870 –Connector Bolt ¼-20x23mm Nylok
b. (4) 70871 –Connector Nut ¼-20x17mm
c. (2) 77813 –Allen wrench 3/16” Short Arm
d. (17) 70054 –SM Screw #10x.75 HI.LO PTH
#10x3/4” Wood Screw
P/N: 70054
(QTY: 32)
P/N: 70867 –Connector Bolt ¼-20x23mm
P/N 70871 –Connector Nut ¼-20x17mm
(QTY: 8 of each)
Button Hd Scrw M8x20mm
P/N: 70088
(QTY: 3)
Allen Wrench 3/16”
P/N: 77813
(QTY: 4)
3/8”-16x.625 Dog Nut Screw
P/N: 77741
(QTY: 8)
Table Top
(QTY: 1)
Y- Leg Sets
(QTY: 1 set of 2 Legs)
Modesty Panel
(QTY: 1)
Wire Manager
(QTY: 1)
L Brackets
(Pre-
attached
to wire
manager.
Remove
before
assembly)

For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
You may also place your order online at
www.smithsystem.com
Form# 179844 04/2013
Assembly Instructions
Step 1: Place the top on a smooth, clean surface with the bottom facing up, being careful not to scratch
the top surface.
Step 2: Align the Y-legs and the “L”brackets with the Predrilled holes, but only attach the “L”brackets to
the top using (4) Wood Screws. (See Picture #1)
Step 3: Loosely attach the Panel to the Y-Legs using the (4) Connector Bolts (See Picture #2). ONLY HAND
TIGHTEN THE BOLTS.
Step 4: Using the remaining wood screws, attach the Y-Legs and the panel to the top. Go back and
tighten the bolts from Step 3.
Drawing 1
Drawing 2

For Assistance in assembling product, missing or damaged parts,
or to place an order, please contact customer service at 800-328-1061
You may also place your order online at
www.smithsystem.com
Form# 179844 04/2013
Step 5: Place the wire manager into the hooks located at the back of the panel. Using the (2) Button
Head Screws, attach the wire manager to the “L”Brackets (See Drawing 3).
Step 6: Adjust the legs to the desired height by loosening the 3/8”-16 Dog Nut Screws and pulling out
the lower part of the leg to the desired height (See Drawing 4). Use the Allen wrench provided to loosen
screws.
Drawing 3