Inside Weather JORN DESK User manual

JORN DESK

Gather Your Eggs...
Base Desk Parts
Back
Lower Shelf
Desk Top
Note: Please retain all boxes until you are certain that your product isn’t damaged and that you
do not wish to return it. Disposal of boxes may prevent/delay our ability to resolve your request.
Left Leg Right Leg
Ratchet Long Hex Bit

More Eggs...
Optional Parts
(Parts included based on options chosen)
Left Pedestal Right PedestalLong Shelf
Monitor Stand
Brackets + Thumb
Screws & T-Slot Nuts
Note:
Number of Thumb Screws,
T-slot nuts and short bolts
vary depending on set-up.
Short Bolts
Plastic Dots
(2 Per Bracket)

Step 1: Attach the Legs
Place the Desk Top upside
down on a soft surface to
protect from scratches.
Take your first leg and make sure that the plastic
connectors of the leg are facing towards the center
of the desk and the angled part of the leg is facing
towards the front.
Align the leg connectors with the holes in the Desk Top.
Fasten to the top using the provided ratchet and long
hex bit attachment. Tighten at an angle. The plastic
connectors have covers which can be placed on after
all bolts are in place.
Plastic Cap to cover bolt opening

Step 2: Install Second Leg
Repeat previous instruction
for the other leg
Note: When fitting the peices together, make sure the connecting screws are
retracted inside their housing. Having the screw out could damage your surfaces.

Step 3: Attach Back Panel
Place the back panel down on a soft
surface to protect from scratches.
Rotate the desk top onto the back panel.
The connectors on the desk top will align
with the top row of holes on the back panel.
Fasten the desk top and
legs to the back panel.

Next take your bottom shelf, with connector
openings facing towards the bottom of the
legs, and align the connectors with the holes
on the back panel and the legs. Fasten the
shelf into place.
Step 4: Attach the Lower Shelf
Step 5: Turn Desk Upright
This completes the assembly of
the base desk. The next section
will discuss the attachments
Use plastic covers to
cover bolt openings
after all are tightened.

Step 6: Attachment Options
Left Pedestal Right PedestalLong Shelf
Brackets + Thumb
Screws & T-Slot
Nuts
Monitor Stand
The desk comes with different options.
Your desk will include the parts you need
for the option you chose at checkout.
The assembly for any option is the same.
Short Bolts

Step 6: Attachment Options (Continued)
First choose the height you would like your
shelves to be. There are 2 options, either
use the 2 top holes, or the 2 bottom holes.
Next, insert 2 thumb screws through your
selected holes on the bracket.
Take your t-slot nuts and place them onto
your screws and turn them once. With
the long side of the nuts parallel to the
ground insert the nuts and screws into the
slots on the back panel.
With the bracket in position, slowly tighten
the thumb screws, the t-slot nut should
rotate slightly so that it is perpendicular to
the ground.
Once it is perpendicular, fully tighten the
screws. Repeat for all shelves.
IMPORTANT! Your t-slot
nuts should look like
this, failure to attach
correctly could result in
your shelf failing.
View from the inside
T-Slot Nut

Step 7: Add Your Shelf Option
Insert the bolts through the brackets
into the shelf and tighten.
Shelf can be adjusted forwards or
backwards to your desired distance.
If your shelves do not sit level at 90
degress, we have included sticky
plastic dots to help level them out.
Place the dots on either side of the
slot towards the front end of the
bracket. If you need to adjust the
angle, you can reposition them on the
bracket moving towards the mounting
bolt to increase the shelf angle
or away from the mounting bolt to
decrease the shelf angle.
Plastic Dots

DONE!