Target Lunenburg media cabinet TGLNBGTVGY User manual

>>
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
lunenburg
media cabinet
assembly instructions
style # TGLNBGTVGY
dpci # 249-10-2251
tcin # 54158118

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4
parts list 5
how to use the cam lock system 6
assembly 7-18
how to adjust door alignment 19
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 27
wooden dowel
(H2) x 28
cam bolt
(H3) x 28
cam
(H4) x 4
knob
(H5) x 4
knob bolt
(H6) x 8
shelf support
(H7) x 25
15mm pan head screw
(H8) x 24
at head scew
(H9) x2
magnet
(H10) x 2
22mm pan head screw
(H11) x 1
19mm pan head screw
(H12) x 1
wall strap
(H13) x 2
washer
(H14) x 1
wall anchor
(H15) x 1
wall screw

5
exploded diagram
ITEM DESCRIPTION QUANTITY
1 top panel 1
2 left side panel 1
3 right side panel 1
4 bottom panel 1
5 bottom front rail 1
6 bottom rear rail 1
7 back panel 1
8 upper front rail 1
9 shelf 2
10 partition 1
11 partition rail 1
12 left door 2
13 right door 2

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cross-bored
hole(s) and insert all the way until
panels are ush
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
6
4. 5.
1. 2. 3.

step 1: attach magnets to upper front rail
(H7) x 4
15mm pan
head screw
(H9) x 2
magnet
1.1. Align 15mm pan head screws with pre-drilled holes to attach magnet to upper front rail. Do not over tighten screws.
7

step 2: attach rails to partition and bottom panel
(H1) x 8
wooden dowel
(H2) x 10
cam bolt
(H3) x 10
cam
2.1. Carefully tap small wooden dowels into place in partition rail, bottom front rail, and bottom rear rail. Leave 1/2” of the dowels sticking out.
2.2. Screw-In cam bolts must be screwed down ush in partition rail, bottom front rail, and bottom rear rail.
2.3. Refer to page 6 for instructions on how to use the cam lock system.
2.4. Do not over tighten bolts.
8
wooden dowel
(H2) x 10
cam bolt
(H3) x 10
cam

9
step 3: attach partition to bottom panel
(H1) x 1
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam
3.1. Carefully tap small wooden dowels into place in bottom panel. Leave 1/2” of the dowels sticking out.
3.2. Screw-In cam bolts must be screwed down ush in bottom panel.
3.3. Refer to page 6 for instructions on how to use the cam lock system.
3.4. Do not over tighten bolts.

step 4: attach left side panel
(H1) x 6
wooden dowel
(H2) x 3
cam bolt
(H3) x 3
cam
4.1. Carefully tap small wooden dowels into place in left side panel. Leave 1/2” of the dowels sticking out.
4.2. Screw-In cam bolts must be screwed down ush in left side panel.
4.3. Refer to page 6 for instructions on how to use the cam lock system.
4.4. Do not over tighten bolts.
10
(H1) x 6
wooden dowel
(H2) x 3
cam bolt
(H3) x 3
cam