Bilanciai DD1050 User manual

ENGLISH
Code 81320278 - 02/05/2016 WEIGHING TERMINAL QUIK START
2. Language selection
1. Unpacking and Installation
3. Touch-screen calibration
4. Network Setup
Once the congurations have been made, wait for the application to
upload completely and the les to activate.
International Setups
- International Setups : English
- User interface language : English
- Input language : EN
OK
TOUCH-SCREEN calibration
Press the “touch screen” dis-
play within 5 seconds from
powering.
Select “International Setups”.
Press “OK”.
Press the “touch screen” dis-
play within 5 seconds from
powering.
Select “TOUCH-SCREEN
calibration” to re-calibrate the
screen (follow the guided pro-
cedure).
Network settings
Press the “touch screen” dis-
play within 5 seconds from
powering.
Select “Network settings” to
enter the network parameters
of a connection (follow the
guided procedure).
DD1050
DD1050i
1
Remove the terminal
from the pack.
Connect:
A. electric power
supply
B. weighing plat-
form
C. any peripheral
equipment used
(e.g.: printer)
Press to power
the terminal.
Available
connections:
1. USB HOST Ports
• Slot for optional
cards
• Scales
• COM2 Port
• COM1 Port
• Expansion for
SD card
• Ethernet Port
10/100 Mbps
• Power supply
DD1050
DD1050i
www.coopbilanciai.it

5. RCD weighing
1
2
3
4
5
6
7
6. RPD/AdR weighing
1
2
3
4
Società Cooperativa Bilanciai Campogalliano - 41011 Campogalliano (MO) Italy
Via S. Ferrari, 16 - Tel. [phone] - Fax [phone]
Web: http://www.coopbilanciai.it - E-mail:[email protected]
Customer Assistance Service Tel. [phone] - Fax [phone]
DECLARATION OF CONFORMITY
N° dd1050_0
SOCIETÀ COOPERATIVA BILANCIAI A.R.L.
We: Via S. Ferrari, 16
41011 Campogalliano (MO)- Italy
declare upon our sole responsibility that
the product: Electronic weighing terminal DD1050 / DD1050i
and its optional equipment
described in this declaration, complies with the relevant harmonised
standards of the European Union
2014/30/EU (EMC) : EN 61000-6-3:2007
EN 61000-6-4 :2007
2014/35/EU (LVD) : EN60950-1:2006
2014/31/EU (NAWI) : EN 45501: 2015
The terminal is also suitable for the creation of non-automatic weighing
instruments approved with the “CE Type Approval Certicate” in
conformance with the requirements of Directive 2014/31/EU (NAWI).
The product bears CE marking.
Campogalliano, this day ............................
Signed for and on behalf
of the manufacturer
WARNINGS
Do not install in places with potentially explosive gas or dust;
• This electrical or electronic device cannot be disposed of
as solid urban waste.
• It must be disposed of separately.
For further information visit the website www.coopbilanciai.it.
Reset the terminal.
Drive the empty vehicle on to
the weighing platform.
Make the entry printout.
Drive the vehicle off the
weighing platform.
Recall the RCD code:
•Select the weight made
and press “OK”.
Drive the loaded vehicle on
to the weighing platform.
Make the exit printout.
Reset the terminal.
Drive the loaded vehicle on
to the weighing platform.
Recall the RPD (or AdR)
code:
•Select the code of the
vehicle and press “OK”.
or (if the code does not ex-
ist):
• Enter the vehicle's
data into a new code
and conrm.
•Select the new code
and press “OK”.
Make the exit printout.
RCD
RPD
SOCIETÀ COOPERATIVA
BILANCIAI
Weighing Instruments and Technologies
02-05-2016