Billion SG6300NZL User manual

www.billion.com.tw
www.smartgrid.com.tw
SG6300NZL Quick Start Guide

www.billion.com.tw
www.smartgrid.com.tw
Chapter 1: SG6300NZL Hardware Installation
1.1 SG6300NZL Overview
1.2 Internet Installation
1.3 ZigBee Pairing
1.4 RS485 Installation
Chapter 2: Network Configuration
2.1 Configuring a PC in Windows 7
Chapter 3: Factory Default Settings
Chapter 4: Information from your ISP
Chapter 5: Configuring internet with your Web Browser
5.1 Internet connection configuration by Quick Start
Chapter 6: Energy Management with ZigBee device
6.1 ZigBee Configuration
6.2 ZigBee Device Monitor
Chapter 7: Energy Management with RS485 device
7.1 RS485 Configuration
7.1 RS485 Device Monitor

www.billion.com.tw
www.smartgrid.com.tw
Chapter 1: SG6300NZL Hardware Installation
1.1 SG6300NZL Overview
SG6300NZL Front Panel LEDs
1 Power Green: Power ON
Red: System failure. Restart the device or contact
2 LAN
Lit up:
Successfully connected with a broadband connection device
Blinking:
Data being transmitted/received
3 WAN
Lit up:
Successfully connected with a broadband connection device
Blinking:
Data being transmitted/received
4 USB Green:
Connecting to a USB dongle or a hard drive.
5 Wi-Fi
Lit up:
Successfully connected with a broadband connection device
Blinking:
Data being transmitted/received
6 ZigBee
Flashes about once every 3 seconds when the wireless
connection is established.
Flashes about 3 times per second when the device is set to the
state waiting for being joined by other smart meters.
7 RS485 Green:
Build up the connection between Gateway and RS485 device
8 WWAN
4G LTE status
Green: Excellent signal condition
Green flashing quickly: Good signal condition
Orange flash quickly: Fair signal condition
Orange flash slowly: Poor signal condition
Orange: No signal

www.billion.com.tw
www.smartgrid.com.tw
Off: No LTE module
9 Internet Green: Connect to internet
Orange: Disconnect to internet
SG6300NZL Rear Panel
1 RS485 Connect to RS485 device
2 SD Card Data storage
3 USB Data storage
4 WAN WAN 10/100M Ethernet port (with auto crossover support);
connect Cable modem here.
5 LAN
Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the
LAN ports when connecting to a PC or an office/home network
of 10Mbps or 100Mbps.
6 ZigBee Push ZigBee button to trigger ZigBee function, thus smart
meter allowing join in is starting
7 Reset
To be sure the device is being turned on press RESET button for
6 seconds and above: restore to factory default settings.
(Cannot
login to the router or forgot your Username/Password. Press
the button for more than 6 seconds).
Caution: After pressing the RESET button for more than
6 seconds, to be sure you power cycle the device again.
8 Power Connect it with the supplied power adapter.
9 Switch Device is power on/off.

www.billion.com.tw
www.smartgrid.com.tw
1.2 Internet Installation
EWAN Installation
SG6300NZL’s WAN port connects to backbone router’s LAN port.
Please refer 5.1 Internet connection configuration by Quick Start to set internet.
4G LTE Installation
Insert the SIM card with the gold contact facing down.
Please refer 5.1 Internet connection configuration by Quick Start to set internet.

www.billion.com.tw
www.smartgrid.com.tw
1.3 ZigBee Pairing
Example SG3015 serials pair to SG6300NZL
STEP_1 Ensure the ZigBee device power on and not join any ZigBee coordinator.
If Status LED lit green that mean ZigBee Meter is waiting mode, please go STEP 3
If Status LED blinking green that mean ZigBee Meter has been pair other SG6300NZL,
Before pair ZigBee Meter with SG6300NZL, please refer ZigBee Meter UM to do
un-pairing.
STEP_2 Push ZigBee button on the rear panel of the ZigBee Coordinator to make a connection.
STEP_3 Then, ZigBee LED in the front panel will blink quickly around 60 seconds
STEP_4 The smart meter will be automatically paired and joined to the ZigBee network.
The Meter Status LED would blink slowly and steadily, indicating that the power meter is
successfully paired
STEP_5 Access to SG6300NZL’s WEB GUI to configure your ZigBee Device
Please refer 6.1 ZigBee Configuration

www.billion.com.tw
www.smartgrid.com.tw
1.4 RS485 Installation
Example SG3010S serials connect to SG6300NZL by RS485
STEP_1 Install SG3010S in the real side, ensure meter power ON.
STEP_2 SG3010S’s RS485+ connect to SG6300NZL’s RS485+
SG3010S’s RS485- connect to SG6300NZL’s RS485-
STEP_3 Access to SG6300NZL’s WEB GUI to configure your ZigBee Device
Please refer 7.1 RS485 Configuration

www.billion.com.tw
www.smartgrid.com.tw
Chapter 2: Network Configuration
2.1Configuring a PC in Windows 7
1. Go to Start. Click on
Control Panel.
2. Then click on Network and
Internet.
3. When the Network and
Sharing Center window
pops up, select and click on
Change adapter settings
on the left window panel.
4. Select the Local Area
Connection, and right click
the icon to select
Properties.

www.billion.com.tw
www.smartgrid.com.tw
5. Select Internet Protocol
Version 4 (TCP/IPv4) then
click Properties.
6. In the TCP/IPv4 properties
window, select the Obtain
an IP address
automatically and Obtain
DNS Server address
automatically radio
buttons. Then click OK to
exit the setting.
7. Click OK again in the Local
Area Connection
Properties window to apply
the new configuration.

www.billion.com.tw
www.smartgrid.com.tw
Chapter 3: Factory Default Settings
Before configuring the Billion SG6300NZL router, you need to know the following default
settings.
Web Interface: (Username and Password)
Username: admin
Password: admin
The default username and password are “admin” and “admin” respectively.
Device LAN IP settings
IP Address: 192.168.5.254
Subnet Mask: 255.255.255.0
ISP setting in WAN site
Obtain an IP Address Automatically
DHCP server
DHCP server is enabled.
Start IP Address: 192.168.5.100
IP pool counts: 100
LAN and WAN Port Addresses
The parameters of LAN and WAN ports are preset at the factory. The default values are
shown below
LAN Port WAN Port
IP address 192.168.5.254 The DHCP function is
enabled to automatically get
the WAN port configuration
from the ISP.
Subnet Mask 255.255.255.0
DHCP server function Enabled in LAN port
IP addresses for
distribution to PCs
100 IP addresses continuing
from 192.168.5.100 through
192.168.5.199

www.billion.com.tw
www.smartgrid.com.tw
Chapter 4: Information from your ISP
Before configuring this device, you have to check with your ISP (Internet Service Provider)
what kind of services are provided, such as PPPoE, Obtain an IP Address Automatically,
Fixed IP address.
Gather the information as illustrated in the following table and keep it for reference.
PPPoE
Username, Password, Service Name, and Domain Name
System (DNS) IP address (it can be automatically assigned
by your ISP when you connect or be set manually).
Obtain an IP Address
Automatically
DHCP Client (it can be automatically assigned by your ISP
when you connect or be set manually).
Fixed IP Address
IP address, Subnet mask, Gateway address, and Domain
Name System (DNS) IP address (it is fixed IP address).

www.billion.com.tw
www.smartgrid.com.tw
Chapter 5: Configuring Internet with your Web Browser
Open your web browser, enter the IP address of your SG6300NZL, which by default is
192.168.5.254, and click “Go”, a user name and password window prompt appears. Enter
the user name and password that your Administrator has set for you and select the
Account Type, then click Login. When you are authorised, you will access to the
router.The default username and password are “admin” and “admin” respectively for the
Administrator account type.
5.1: Internet Connection by Quick Start
This is a useful and easy utility to help you to setup the router quickly and to connect to your ISP
(Internet Service Provider) with only a few steps. It will guide you step by step to setup password,
time zone, wireless and WAN settings of your device. The Quick Start Wizard is a helpful guide for
the first-time users to the device.
For detailed instructions on configuring WAN settings, see refer to the Interface Setup section.

www.billion.com.tw
www.smartgrid.com.tw
Click NEXT to move on to STEP_ 1.
STEP_1 Password
Set new password of the “admin” account to access for router management. The default is
“admin”.
Once changed, please use this new password next time when accessing to the router. Click NEXT to
continue. Suggest do not change the password.
STEP_2 Time Zone
Choose your time zone. Click NEXT to continue.
STEP_3 Wireless
Set up your wireless connection if you want to connect to the Internet wirelessly on your PCs. Click
NEXT to continue.

www.billion.com.tw
www.smartgrid.com.tw
STEP_4 ISP Connection Type
Set up your Internet connection.
4.1 Select an appropriate WAN connection protocol then click NEXT to continue.
Input all relevant 3G/4G-LTE parameters from your ISP.
4.2 If selected EWAN
If selected PPPoE, please enter PPPoE account information provided by your ISP. Click NEXT to
continue. Or, others protocol assigned by your ISP.

www.billion.com.tw
www.smartgrid.com.tw
If selected Dynamic IP Address. When connecting to the ISP, Billion SG6300NZL also functions as a
DHCP client. Billion SG6300NZL can automatically obtain an IP address, subnet mask, gateway
address, and DNS server addresses if the ISP assigns this information via DHCP.
If selected Static IP Address. You will need to enter in the Connection type, IP address, Netmask,
and gateway address, provided to you by your ISP. Each IP address entered in the fields must be in
the appropriate IP form, which are four IP octets separated by a dot (x.x.x.x). The Router will not
accept the IP address if it is not in this format.
STEP_5 Quick Start Completed
The Setup Wizard has completed. Click on BACK to modify changes or mistakes. Click NEXT to save
the current settings.
STEP_6 Quick Start Completed

www.billion.com.tw
www.smartgrid.com.tw
Chapter 6: Energy Management with ZigBee device
SG6300NZL build basic energy management application on WEB GUI, user can monitor real time
power information and remote control power meter on the WEB GUI.
6.1 ZigBee Configuration
Once ZigBee Meter joined ZigBee Network, this page will show on ZigBee information.
Advance->Power Management-> Meter Config
Allow Join: SG6300NZL will start allow ZigBee node joining to ZigBee Network.
Scan Meter: Show the current ZigBee nodes on the WEB GUI.
Meter List: Show the EUI64 of ZigBee nodes.
Alias: Setup alias name for ZigBee nodes.
Identify: Click “Identify” button on the WEB GUI, then INC. LED will be blinking orange.
It can help user recognize which meter is under controlled.
Remove: Remove ZigBee nodes from ZigBee Network.

www.billion.com.tw
www.smartgrid.com.tw
6.2 ZigBee Device Monitor
Show various power information from ZigBee Meters measured
Route
Advance->Status->Power Status
Device ID: EUI64 of ZigBee Meters.
Appliance: Base on Alias Name.
Power Status: Show current relay status of ZigBee Meter.
ON: Relay ON
OFF: Relay OFF
N/A: Not support relay feature
Signal Strength: Show the Signal Strength between ZigBee nodes and next ZigBee nodes.
Power information:
Show Power information include as below
Voltage, Current, Frequency, PF, Active Power, Apparent Power, Mainenergy.
When you click blue link you will see detail power information.

www.billion.com.tw
www.smartgrid.com.tw
Chapter 7: Energy Management with RS485 device
7.1 RS485 Configuration
Advance->Power Management-> RS485 Config
Set Baud Rate for RS485 used.
Set the RS485 device to each ID, please ensure all RS485 devices already connect to SG6300NZL.

www.billion.com.tw
www.smartgrid.com.tw
7.2 RS485 Device Monitor
Show various power information from RS485 Meters measured
Route
Advance->Status->RS485 Status
Address: Modbus address of RS485 Meters.
Model Name: The model name of RS485 device.
Power Status: Show current relay status of RS485 Meter.
ON: Relay ON
OFF: Relay OFF
N/A: Not support relay feature
Success:
The number of SG6300NZL reads RS485 device success.
Retry:
The number of SG6300NZL re-reads RS485 device.
Reset:
Reset the number of success and retry.
Power information:
Show Power information include as below
Voltage, Current, Frequency, PF, Active Power,
Apparent Power, Mainenergy (accumulation Power).
When you click blue link you will see detail power information.