biodex 950-440-K900 User manual

FN: 11-124 5/11
UPGRADE RETROFIT KIT FOR
BALANCE SYSTEM SD DISPLAY
950-440-K900
BIODEX
Biodex Medical Systems, Inc.
20 Ramsay Road, Shir ey, New York, 11967-4704, Te : 800-224-6339 (Int’l 631-924-9000), Fax: [phone], Emai : [email protected], www.biodex.com

— 2—
This manual covers installation procedures for the following product:
950-440-K900 Retro it Kit, Balance System SD 12.1" LCD Display
This product can be used with the following products:
950-300 BALANCE SYSTEM SD, 115V
950-302 BALANCE SYSTEM SD, 230V
950-304 BALANCE SYSTEM SD, 100V
BALANCE SD DISPLAY UPGRADE PROCEDURE
TOOLS NEEDED: HILLI S HEAD SCREWDRIVER, 7/16 IN. WRENCH
PARTS NEEDED: RETROFIT KIT /N 950-440-K900
1. Turn off display and unplug unit from A/C outlet.
2. Remove the existing display from the pivot bracket by removing the (4) hillips head screws
and disconnecting the display cables @ connectors 2, J7 and J11 located at the back of the
display.
3. Using a 7/16 in. wrench remove the acorn nut and threaded rod that secures the pivot brack-
et to the display tube assembly and then remove the existing pivot bracket.
BALANCE SYSTEM SD DISPLAY
Pivot Bracket
Serial Cable P2
Display Cable to J11 &
Tilt Se sor cable to J7
Acor Nut & Threaded Rod

— 3—
4. Attach the new display pivot bracket from the retrofit kit to the display tube assembly using
the same hardware that was used to attach the original display pivot bracket.
5. Reconnect the main display cable (J7 from original display) and tilt sensor cable (J11 from
original display) to the new 12 in. display and attach the display to the pivot bracket using
the (4) 10-32 x .38 hillips head screws that are included with the retrofit kit.
6. lug unit back into A/C outlet. erform both platform actuator and tilt sensor calibration
procedures (see attached) and then check the unit for normal operation.
TABLE OF CONTENTS
Diplay Cable J7
Tilt Se sor Cable J11

BALANCE SD PLATFORM ACTUATOR CALIBRATION
1. Tap the touch screen to turn on the display.
2. Touch <UTILITIES> on the screen.
Note: The ext step requires pressi g the hidde keypads i the upper right a d left cor ers of the
display's touch scree .
3. Touch Top-Right Corner, Top-Left Corner, Top-Right Corner successively, to access the
<SYSTEM MAINTENANCE> menu on the display.
4. Touch <SYSTEM MAINTENANCE>.
5. Touch <DIAGNOSTICS>
6. Touch <PLATFORM ACTUATOR> on the screen.
7. ress the <DOWN ARROW> on the screen until the motor stalls (bottoms out). Then look at
the READING in the bottom right of screen and bring motor up 3 digits.
8. Touch <SET NEW MIN> on the screen to calibrate level 1.
9. Touch and hold the <UP> arrow on the screen until the motor stalls.
10. Touch <SET NEW LOCKED> on the screen to calibrate the locked position.
11. Touch <COMPENSATION> at the bottom of the screen and listen for the actuator. The
“arrow” indicator will move also.
12. Touch <BACK> on the screen four times to exit and return to the main screen.
TILT SENSOR CALIBRATION PROCEDURE
1. Install the platform if it’s not already installed.
2. Tap the touch screen to turn on the display.
3. Touch UTILITIES” on the screen.
Note: The ext step requires pressi g the hidde keypads i the upper right a d left cor ers of the
display's touch scree .
4. Touch Top-Right Corner, Top-Left Corner, Top-Right Corner successively, to access the
SYSTEM MAINTENANCE” menu on the display.
5. Touch SYSTEM MAINTENANCE”.
6. Touch DIAGNOSTICS”
CautioN!: The platform will release whe you perform the ext step
atteNtioN!: La plate-forme libérera qua d vous exécutez la prochai e étape.
7. Touch TILT SENSOR” to release the platform.
8. Depress the platform to the maximum 9 o’clock position. The LEFT (min)”
window will turn green signifying proper calibration.
9. Depress the platform to the maximum 3 o’clock position. The RIGHT (max)”
window will turn green signifying proper calibration.
10. Depress the latform to the maximum 6 o’clock position. The BACKWARD (min)”
window will turn green signifying proper calibration.
11. Depress the platform to the Maximum 12 o’clock position. The FORWARD (max)”
window will turn green signifying proper calibration.
12.YOU MUST press the BACK key 4 times to save and exit the calibration screen.
INTRODUCTION
BIODEX
Biodex Medical Systems, Inc.
20 Ramsay Road, Shir ey, New York, 11967-4704, Te : 800-224-6339 (Int’l 631-924-9000), Fax: [phone], Emai : [email protected], www.biodex.com
Certified Quality Management System
!
!