BIONIME RIGHTEST GT200 User manual

1 3
1 2 3
2
Blood Glucose Monitoring System GT200 GETTING STARTED GUIDE (For self-testing and professional use)
Test Strip Vial Lancing Device
Front View of Meter Back View of Meter
Test Strip
Sample Port
View Window
PlungerHub
Lancet Carrier
Release Button
Adjustable Depth Cap
Clear Cap
Left Button ( )
Main Button ( )
Display Window
Test Strip Port
Right Button ( )
Battery Cover
Meter Label
Control Solution
1) Turn the meter over. Press the battery cover to open.
2) Install the 2 CR2032 batteries. Be sure to insert the batteries in the correct direction.
3) Put the battery cover back on until it snaps into place.
3
2
1) Press and release the Main button " " to turn on the meter.
2) Press and hold the Main button " " for 7 seconds to enter the Setting Mode. The year will
flash. (Note: The meter will turn off while you are holding down the button. Continue holding
down the Main button to reach the Setting Mode. You will then be asked to set the year.)
3) Press the Left button " " or Right button " " to change the year.
4) Press the Main button " " to confirm the year and move onto the month setting.
5) Repeat steps 3 and 4 to change the date, time format, hour, minute, volume, and
measurement unit. After pressing the main button to confirm the measurement unit setting,
your set-up has been finished.
NOTE
- In order to ensure proper operation, do not use this meter close to strong sources
electromagnetic radiation.
- Keep the meter free of dust and liquids, including water.
1) Hold the adjustable depth cap in one hand while holding the hub with the other hand. Pull the
cap in the down direction. When a gap appears between the cap and hub, pull the two parts
in opposite directions.
2) Remove the adjustable depth cap.
3) Insert a new disposable lancet firmly into the lancet carrier.
1
TM
Installating the Batteries
Setting Up Your Meter - Setting the Date, Time and Volume
Preparing the Lancing Device
Lancet
Protective cover

4
101-3GM750-XXX EN
Rev. Date:2019-10
Bionime GmbH
Tramstrasse 16
9442 Berneck
Switzerland
E-mail: [email protected] 0197
4675
For more information on how to use your meter and understanding your test results, please see
your RIGHTEST Blood Glucose Monitoring System GT200 User's Manual.
4) Twist off and set aside the protective cover of the disposable lancet.
5) Replace the adjustable depth cap.
6) Choose a depth of penetration by rotating the top portion of the adjustable depth cap to the
desired depth setting. Your setting should be based on your skin type:
" " for soft or thin skin;
" " for average skin;
" " for thick or calloused skin.
7) Hold the hub in one hand and pull on the plunger with the other hand. Release the plunger and
it will automatically move back to its original position near the hub. The device will be cocked.
1) Wash and dry your hands. Take one test strip from the vial. Close the vial cap immediately.
2) Insert the strip into the strip port on the meter with the view window facing up. Push the strip in
until you hear a click. The meter will automatically detect the code number.
3) When you see the flashing blood drop icon on the display window, hold the lancing device to
your fingertip and press the release button.
1a
4) A blood drop size between 0.75 µL and 3.0 µL is required for testing. See Sample Size Example
Chart for drop sizes. Blood drop sizes greater than 3.0 µL may contaminate the meter. A minimum
of a 0.75 µL drop is required for accurate results.
5) Touch and hold the drop to the edge of sample port until you hear a "beep" and the view window
is filled with blood. If the view window is not completely filled with blood, the test will not start.
Discard the test strip and repeat the test with a new test strip.
6) The countdown will begin on the display window. After 5 seconds, your test result will appear.
For more information about your test results, please see your User’s Manual.
3b
4) Sample Size Example
0.75 µL 1.0 µL 1.5µL 2.0 µL 3.0 µL
6
7) Remove the test strip from the meter. Please follow your local regulations to properly discard the
used strip.
8) Pull off the adjustable depth cap. Without touching the used disposable lancet, stick the lancet tip
into the protective cover.
9) Hold the release button in one hand and pull the plunger with the other hand. This will safely eject
the used disposable lancet.
10) Discard the used disposable lancet into an appropriate puncture-proof or biohazard container.
11) Replace the adjustable depth cap after finishing the test.
Alternative site testing: palm or forearm blood sampling
45
8
12
9 10 11
NOTE
- The RIGHTEST Lancing Device is intended for single person use only.
1. Choose the clear cap and follow step 1 and step 2 "Performing a Test".
2. Massage the puncture area of your palm or forearm for a few seconds.
3. Immediately after massaging the puncture area, press and hold the lancing device with the clear
cap against your palm or forearm.
4. Press the release button.
5. Continue holding the lancing device against your palm or forearm. Gradually increase pressure
for a few seconds until the blood sample size is sufficient.
6. Follow step 9 to discard the used disposable lancet.
NOTE: DO NOT test on the palm or forearm if you are testing for hypoglycemia (low blood
glucose).
1b
2
3a
5a
5b
7
Performing a Test
Press for
a few seconds Release button
Palm
Forearm
BIONIME CORPORATION
No. 100, Sec. 2, Daqing St., South Dist.,
Taichung City 40242, Taiwan
Tel: [phone]
Fax: [phone]
http: //www.bionime.com
E-mail: [email protected]