Birlea URB6WCHRUS User manual

URBAN 6 DRAWER WIDE CHEST
IMPORTANT : READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE OR
USE YOUR URBAN 6 DRAWER WIDE CHEST.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ASSEMBLY:
Assembly should be carried out with this item laying flat, not standing upright.
Assemble on a soft, clean surface to prevent damages.
To erase the numbers printed on the pieces, use the rubber inside the accessories pack.
HEALTH & SAFETY:
DO NOT use this product if any parts are missing, damaged or worn.
DO NOT use this product unless all fixings are secured.
Always use on a level, even surface.
CARE & MAINTENANCE:
Periodically check all screws & fixings to ensure they are secure.
DO NOT push this product as this will cause damage.
Always lift this product with two people to repositions.
Keep any sharp objects away from this product.
ASSEMBLY INSTRUCTIONS
www.birlea.com Page of 8
Vendor: S000350
1

2
Page of 8
Vendor: S000350
Parts List Hardware List ( BOX 2 )
Part Descripion Qty Part Description Qty
** You will need a small mallet and a
screwdriver for assembly.
** Some screws and wooden dowel
may remain.
** Note : To secure the item to the wall, hardware E ( 2 pcs ) and P ( 2 pcs ) are not provided.
01 1
Top panel
02
03
04
05
06
07
08
09
10
Bottom panel
Metal middle
1
1
1
4
2
2
Side panel ( Left )
Side panel ( Right )
Metal Side ( Left & Right )
A2
Cam lock
Minifix screw
B
Plastic cap
M8 x 30mm Wood Dowel
C
D
E
F
G
H
I
J
M6 x 50mm CSK Cap Wood screw
M3.5 x 16mm C.B Screw
14
14
14
12
6
78
48
Handle 100.96. BLM
Allen key M4 1
6
Handle screw M4 x 19mm 4
JCBC screw M6 x 30mm 10
JCBC screw M6 x 40mm 4
M4 x 38mm C.B Screw
A1
A3
11
2
5
4
14'' Drawer slide (Left / Right)
14'' Drawer slide (Left / Right)
12
12
L2
M1
12
13
14
4
M2
8'' x 1'' PP tape 2
1
Center panel
2
Back panel
K
L1 Stud 192
Stud 192 screw
8
8
Wall plug -
N
Box
1
2
Drawer front ( Up )
Drawer front ( Down )
2
Back bone ( L/R )
15
16
Drawer side ( Up )
Drawer back ( Up )
Drawer side ( Down )
Drawer back ( Down )
6
2
Drawer bottom
1
1
1
1
1
1
1
1
1
3
2
2
2
2
2
O
Handle screw M4 x 35mm 8
2
15
04
05
03
15
01
02
06
06 07
07
16
16
N
Metal leg 50 x 50 x H165mm (Center) 1
P
11 X4
10 X4
10
X4
GX4
08 X4
14 X4
09 X2
GX2
13 X2
12 X2
12
X2
14 X2

3
Page of 8
Vendor: S000350
Step 1: Insert hardware parts A1, A2, B, D and M1 into parts (1), (3), (4), (5) & (7) like the below.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
M1
M1
M1
DDD
A1
07
A2
01
05
Right face
05
Left face
x6
x4
Bx4
x9 x9 x9
M1
M1
M1
DDD
x3 x3 x3
A1
07
x4
A1
A3
A1 A2
A3 x 8
Step 2: Attach back bone (7) to side panel (3) and center panel (5) using hardware A1 and A2
with a screwdriver (not provided).
Attach back bone (7) to side panel (4) and center panel (5) using hardware A1 and A2
with a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
03
04
A2 x2
A2 x2
A2 x2
A1 x2
A1 x2
A1 x2
Bx4
Bx4
A2 x2
05
03
04
07
07

4
Page of 8
Vendor: S000350
Step 3: Attach side panel (3), (4) and center panel (5) to top panel (1) using hardware A1 and A2 with
a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Step 4: Insert back panel (6) along the slot.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
A1
A1
A3
A2
A3 x 6
05
03
04
07
07
01
01
07
07
04
03
05
06
06
Step 5: Attach bottom panel (2) to side panel (3), (4) and center panel (5) using hardware C and F.
Assemble hardware N onto bottom panel (2) using hardware D with a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
02
C
F
N
D
C x 6
F
D x 4
N x 1
07
07
06
06
03
02
04
05

5
Page of 8
Vendor: S000350
F
J
16
Step 6: Attach hardware L1 into top panel (1), bottom panel (2), side panel (3) and (4) using hardware L2
with a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
L1
L2
15
F
J
15
F
K
L2 x 8
L1 x 8
F
K x 4
J x 10
07
07
06
06
02
03
Step 7: Attach metal middle (16) to bottom panel (2) using hardware J and F.
Attach metal side (15) to side panel (3) and (4) using hardware J and F.
Attach metal side (15) to metal middle (16) using hardware K and F.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
02
16
04
01
03
15
15
04
07
07
06
06

6
Page of 8
Vendor: S000350
M2
M2
M2
D
D
D
D
D
D
M2
M2
M2
Step 8: Assemble the drawer components using hardware D, E, G, I and M2.
In this step only show one of the drawers.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Smaller drawers
1. Insert Hardware part (G) to the drawer front (up) (8) using hardware part (I)
2. Attach the drawer side (up) (10) to the drawer back (up) (11) and the drawer front (up) (8)
using hardware part (E).
3. Slide in the drawer bottom (14) then attach the drawer side (up) (10) using hardware part (E).
4. Attach the hardware part (M2) to the drawer sides (10) using hardware part (D).
D x 24
E x 32
M2 x 8
( L/R )
G x 4
I
G
X4
08
X4
08 X4
10
X4
11
X4
14 X4
08 X4
10
X4
11
X4
14 X4
11
X4
I x 8
08 X4
10
X4
10 X4
X8
14 X4
11
X4
10 X4
10
X4
08 X4
Ex16
Ex16

Page of 8
Vendor: S000350
7
H
G
X2
09
X2
09 X2
12 X2
13 X2
14 X2
09 X2
12
X2
13 X2
14 X2
12 X2
09 X2
12
X2
13 X2
X4
14 X2
13 X2
12 X2
09 X2
12
X2
Ex8
Ex8
M2
M2
M2
D
D
D
D
D
D
M2
M2
M2
D x 12
E x 16
M2 x 4
( L/R )
H x 4
G x 2
Step 9: Assemble the drawer components using hardware D, E, G, H and M2.
In this step only show one of the drawers.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Larger drawers
1. Insert Hardware part (G) to the drawer front (down) (9) using hardware part (H)
2. Attach the drawer side (down) (12) to the drawer back (down) (13) and
the drawer front (down) (9) using hardware part (E).
3. Slide in the drawer bottom (14) then attach the drawer side (down) (12) using hardware part (E).
4. Attach the hardware part (M2) to the drawer sides (12) using hardware part (D).

Step 11: To secure the item to the wall use hardware E, O and P using a screwdriver (not provided).
Then attach hardware part O to top panel (1) using hardware D with a screwdriver (not provided).
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
Additional Information:
· For complete product information, images and dimension diagrams please visit the website
www.birlea.com
· If you have any issues with your item please contact the retailer directly you purchased it from
who will be able to resolve any issues with Birlea.
· Why don't you send us photos of your assembled furniture to [email protected] to be shared in
our #birleahome feature on instagram.
E
O
P
1.
O
D
2.
PLEASE NOTE that wall fixings are not supplied as different wall materials require different fixing
devices. You must use fixings devices suitable for the type of wall you intend to mount product to.
Ensure the head of any screw used has a diameter greater than the mounting hole and the fixing
is safe and secure before use.
Birlea Furniture advise you use the wall straps provided to further enhance the safety of this
product.
D x 2
E x 2
O x 2
P x 2
Step 10: Assemble the drawers in place along the drawer slides.
DO NOT use any power tools as this may damage the frame and will invalidate any claim.
M2
M1 M1
M2
Not Provided.
Not Provided.
08
08
08
08
09
09
01
04
Page of 8
Vendor: S000350
8