Birlea FAIRMONT User manual

Vendor: S000298
www.birlea.com Page 1 of 8
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
HEALTH & SAFETY:
DO NOT jump on this bed frame.
DO NOT use this bed frame unless all xings are secured.
Please keep small parts out of reach of children.
Always use on a level, even surface.
WARNING: If this bed is placed on a non-carpeted oor you must place some protection under all legs to
stop the bed frame from moving. If this is not adhered to there is no guarantee if the bed frame collapses.
CARE & MAINTENANCE:
Assemble in the room of use.
Periodically check all screws & xings to ensure they are secure.
Always lift the bed with two people to reposition.
Keep any sharp objects away from the frame.
DO NOT use this bed frame if any parts are missing,damaged or worn.
DO NOT push the bed frame as this will damage the legs.
FAIRMONT OTTOMAN 5' BED FRAME
IMPORTANT: READ THIS INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR USING YOUR
FAIRMONT OTTOMAN 5' BED
ASSEMBLY INSTRUCTION

1Headboard
4
3
2Footboard
Description 1
1
1
1
Center & Back Bottom panel 1
Front Bottom panel
Box Qty
Part
Vendor: S000298
www.birlea.com Page 2 of 8
Part List
5Side Rail 'Right' 2
6Side Rail 'Left' 2
1
1
2
1
1
7Storage Rail 2 2
8Ottoman Front
9Ottoman Back
10 Ottoman Right
11 Ottoman Left
12 Ottoman Middle
13 Bed Slat
3 1
3 1
3 1
3 1
3 1
3 28
15 Gas Lift Mechanism 4
'Right&Left' with Nuts
216 Gas Spring 'Right&Left'
2
4
14 Strap 3 1

ADowel Pin 8 x 35mm
BMini Fit
Description 1
1
8
Box Qty
Part
Vendor: S000298
www.birlea.com Page 3 of 8
Hardware list
4
CJCBC Bolt M8 x 20mm 1
DJCBC Bolt M8 x 16mm 1
16
16
EFlat washer
FM5 Allen Key 1 1
GBracket 3 4
HPlastic Corner 3
JSingle Slat Cap 3 28
KJCBC Bolt M8 x 40mm 3 20
LHex Nut M8 3 20
M5 Allen Key
I
M
N
O
P
Q
R
**You will need a small mallet and a screwdriver for
Screw Driver Mallet
1 30
Wrench
Base Bracket
Mattress Stopper With Nuts
Screw M8 x 45mm
Hex Nut M8
3 1
3 1
4 2
4 1
4 6
4 6
assembly.
Double Slat Cap 3
4
14

B
5
A
A
B
Vendor: S000298
www.birlea.com Page 4 of 8
.\3_PDFsam_120CM FINSBURY OTTOMAN\3_PDFsam_120CM FINSBURY OTTOMAN_2.BMP
E
1
2
C
F
15
16
16
15
D
O
O
**CENTER POSITION
LONG HOLE
FDE
7
7
6
Step 1: Insert hardware part (A) and (B) into the holes shown on the siderails (5) and (6) then attached the Storage rail (7) to the
siderail as shown and tighten with a screwdriver.
Warning: DO NOT use any power tools as this may damage the frame and will invalid any claim
Step 2: Attach the headboard (1) and footboard (2) to the siderails (5) and (6) using hardware parts (C), (E) and (F).
Warning: DO NOT use any power tools as this may damage the frame and will invalid any claim
Step 3: Attach hardware part (O) to the footboard (2) and siderails (5) and (6) using hardware part (D) and (F).
Attach the gas spring (16) to the gas lift mechanism (15) using the included nut. Then attach the gas lift mechanism (15) to the siderails
(5) and (6) using hardware parts (E), (D) and (F).
Warning: DO NOT use any power tools as this may damage the frame and will invalid any claim