Black & Decker BXSH44004GB User manual

BXSH44004GBwww.blackanddecker.co.uk
This product is only suitable for well-insulated
spaces or occasional use.

ENGLISH (Original instructions)
2
What’s in the box
Instruction Manual
33’’ Tower Heater
Remote Control
Features
1. Control Panel
2. Display Screen
3. Air Outlet
4. Remote Control Storage
5. Power On/Off Switch
6. Timer Key
7. ‘-‘ Key
8. ‘+’ Key
9. Mode Key
10.Oscillation Key
11. On/Standby Key
12.Lock Indicator
13.Unit Indicator
14.Degree Indicator
15.Hour Indicator
16.Heat Setting Indicator
17.Timer Indicator
18.Intelligent Sensor
19.Low Speed Setting
20.High Speed Setting
21.Oscillation Indicator
712
19 20 21
13 146 8 9
10 11
17 15
18 16
4
5
2
1
3

ENGLISH
(Original instructions)
3
Intended Use
Your BLACK+DECKER BXSH44004GB 33’’ PTC
Personal Heater has been designed for heating
small and medium spaces.
This appliance is intended for indoor household use
only.
Thank you for choosing BLACK+DECKER. We hope
that you will enjoy using this product for many years.
Safety Instructions
WARNING: Read all safety
warnings and all instructions.
Failure to follow the warnings and
instructions listed below may result
in electric shock, re and/or serious
injury.
♦ Read this manual carefully before
using the appliance.
♦ The intended use is described in
this manual.
♦ The use of any accessory or
attachment or the performance of
any operation with this appliance
other than those recommended in
this instruction manual may present
a risk of personal injury.
♦ Retain this manual for future
reference.
♦ WARNING: When using mains-
powered appliances, basic safety
precautions, including the following,
should always be followed to
reduce the risk of re, electric
shock, personal injury and material
damage.
Using Your Appliance
Please read the operating
instructions carefully before using
your personal heater for the rst time.
♦ Check that the voltage of the main
circuit corresponds with the rating
of the appliance before operating.
♦ The heater must not be located
immediately below a socket outlet.
♦ Do not use this heater in the
immediate surroundings of a bath,
a shower or a swimming pool.
♦ The appliance is not to be used
by persons (including children)
with reduced physical, sensory
or mental capabilities, or lack of
experience and knowledge, unless
they have been given supervision
or instruction.
♦ In order to avoid overheating, do
not cover the heater.
♦ Children of less than 3 years should
be kept away unless continuously
supervised.
♦ Children aged from 3 years and
less than 8 years shall only switch
on/off the appliance provided that
it has been placed or installed
in its intended normal operating
position and they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand the
hazards involved. Children aged
from 3 years and less than 8 years
shall not plug in, regulate and clean
the appliance or perform user
maintenance.

ENGLISH (Original instructions)
4
♦ CAUTION: Some parts of this
product can become very hot and
cause burns. Particular attention
has to be given where children and
vulnerable people are present.
♦ Children shall not play with the
appliance.
♦ Do not let the cable hang over the
edge of a table or counter or let
it come into contact with any hot
surfaces.
♦ The use of accessory attachments
is not recommended by the
appliance manufacturer, apart from
those supplied with this product.
♦ Do not pull the plug out by the
cable as this may damage the plug
and/or the cable.
♦ Do not use this product for anything
other than its intended use.
♦ This appliance is for household use
only.
♦ Do not carry the appliance by the
power cable.
♦ Do not use the appliance outdoors.
♦ Do not operate with wet hands.
♦ Use of an extension cable with this
appliance is not recommended.
However, if it is necessary to use
an extension lead, ensure that
the lead is suited to the power
consumption of the appliance to
avoid overheating of extension
cable, appliance or plug point. Do
not place the extension cable in a
position where it can be pulled on
by children or animals or tripped
over.
♦ Always unplug the unit when not in
use or before cleaning.
♦ The manufacturer does not accept
responsibility for any damage
or injury caused by improper or
incorrect use, or for repairs carried
out by unauthorised personnel.
Safety Of Others
♦ Close supervision is necessary
when any appliance is used by or
near children.
♦ Children should not play with the
appliance.
♦ Cleaning and user maintenance
should not be undertaken by
children without supervision.
♦ Take care when any appliance is
used near pets.
♦ Do not allow the cord to become
twisted or come into contact with
children.
After Use
♦ While cleaning, DO NOT use a wet
cloth or use water on any part of
the unit, as this may cause a short
circuit or electrical shock.
♦ Keep this unit clean. Do not allow
objects to enter the ventilation
opening as this may cause electric
shock, or damage to the unit.
Switch off at the wall socket then
remove the plug from the socket
when not in use or before cleaning.

ENGLISH
(Original instructions)
5
♦ Check all inlets and outlets from
time to time for accumulated dust.
♦ Disconnect the unit from mains
outlet when it is not in use, or
before relocating or cleaning it.
♦ Switch off, remove the plug from
the socket and let the appliance
cool down before leaving it
unattended and before changing,
cleaning or inspecting any parts of
the appliance.
♦ When not in use, the appliance
should be stored in a dry place.
Children should not have access to
stored appliances.
Inspections And Repairs
♦ Do not attempt to dismantle, repair
or remould any part of the unit. This
should only be done by a qualied
service agent. Even the change of
power cable should be done by a
qualied person.
♦ In the unlikely event the appliance
develops a fault, stop using it
immediately and seek advice from
the manufacturer.
♦ In case of technical problems,
switch off the product and do not
attempt to repair it yourself. Return
the appliance to an authorised
service facility for examination,
adjustment or repair. Always
insist on the use of original spare
parts. Failure to comply with the
above mentioned precautions and
instructions, could affect the safe
operation of this product.
Additional Safety Instructions for
This Appliance
♦ Install the unit on at and hard oor
to diminish vibration or noise.
♦ Always operate the appliance on a
smooth, even, stable surface. Do
not place the unit on a hot surface.
♦ Ensure that the unit is switched off
after use.
♦ Do not immerse cables, plugs or
any part of the appliance in water
or any other liquid.
♦ Operate the unit only at the voltage
specied.
♦ Do not use the unit near open
windows, as contact with rain and
other natural elements could cause
an electrical hazard
♦ Do not put heavy objects on the
appliance.
♦ Do not tip the unit on its side.
♦ Never insert any other object into
the unit body to avoid any hazard
or unit failure.
♦ Do not put the unit close to
heat-generating devices or
near ammable and dangerous
materials.
♦ If the supply cable is damaged,
it must be replaced by the
manufacturer or its service agent or
a similarly qualied person in order
to avoid a hazard.
♦ For optimal airow circulation,
leave a distance of at least 1 metre
around the appliance on every side.

ENGLISH (Original instructions)
6
Always direct the airow in order
to optimise heating. Avoid corners,
small objects and other surfaces
or objects which may impede the
airow.
♦ The appliance must be positioned
so that the plug is accessible.
♦ Always turn the heater off and
unplug it from the mains before
attempting to move it.
WARNING: Do not place the unit
on or near a hot gas electric burner.
Electrical safety
Before use, check that the mains voltage
corresponds to the voltage on the rating plate.
This product must be earthed.
Always check that the mains voltage
corresponds to the voltage on the rating
plate.
♦ Appliance plugs must match the outlet. Never
modify the plug in any way.
♦ Do not use any adapter plugs with earthed (Class
1) appliances. Unmodied plugs and matching
outlets will reduce the risk of electric shock.
♦ To avoid the risk of electric shock, do not immerse
the cord, plug or appliance in water or other liquid.
Extension cables & class 1 product
♦ A 3 core cable must be used as your tool is
earthed and of class 1 construction.
♦ Up to 30m (100 ft) can be used without loss of
power.
♦ If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
BLACK+DECKER Service Centre in order to avoid
a hazard.
Labels on Appliance
The following pictograms along with the date code
are shown on the appliance:
WARNING: Hot surface
WARNING: Do not cover
Warning! Before assembling, switch the appliance
off and remove the plug from the socket.

ENGLISH
(Original instructions)
7
Features
1. Control Panel
2. Display Screen
3. Air Outlet
4. Remote Control Storage
5. Power On/Off Switch
6. Timer Key
7. ‘-‘ Key
8. ‘+’ Key
9. Mode Key
10.Oscillation Key
11. On/Standby Key
12.Lock Indicator
13.Unit Indicator
14.Degree Indicator
15.Hour Indicator
16.Heat Setting Indicator
17.Timer Indicator
18.Intelligent Sensor
19.Low Speed Setting
20.High Speed Setting
21.Oscillation Indicator
Use
About the Controls
♦ Programmable 24-hour timer
♦ 3 heat settings and 2 fan settings
♦ Adjustable thermostat
♦ Oscillation function
Turning the Unit On or Off
♦ To turn the unit On or Off, plug it into a mains
socket and ick the Power On/Off switch at
the back of the appliance to the On position
(represented by the symbol ‘I’). The unit will
give off a beeping sound to indicate it has been
powered up.
♦ To turn the appliance off, press the On/Standby
button on the remote control or the unit’s control
panel while the unit is in operation to put it into
Standby mode. A countdown will begin on the
unit’s LED screen. When the timer reaches ‘0’, the
unit will automatically turn itself off
NOTE: The length of the shut-off countdown timer
will vary depending on the selected heat settings and
the duration of the heating cycle. If the unit was used
at a low setting and for a short time, the cool-down
period will be quicker, and the timer will be shorter;
if it was used at a higher temperature or for a longer
period of time, the cool-down process will take
longer, and the timer will reect this.
♦ When the countdown has concluded and the unit
has returned to Standby mode, ick the Power On/
Off switch to the Off position (represented by the
symbol ‘O’) to turn the unit off.
NOTE: To ensure optimal functionality, take care
to point the remote control directly at the unit’s
LED display when controlling the unit hands-free.
If the remote is not pointed directly at the display,
button presses will not be recognised and the unit’s
performance will be affected. This principle applies
to all remote-controlled functionalities described
below.
Heat Setting Selection
♦ This heater offers a choice of Low, Medium and
High heat settings and Medium and High fan
settings.
♦ Press the ‘MODE’ button on the remote control
or the unit’s control panel to cycle through the
available heat and fan settings. The corresponding
indicator will light up on the unit’s display screen to
show each setting has been selected.

ENGLISH (Original instructions)
8
Temperature Selection
♦ The unit’s temperature can be adjusted manually
in any of the 3 available heat settings.
♦ Use the ‘+’ or ‘-‘ buttons on the remote control
or the unit’s control panel to manually adjust the
heating output temperature. Use the ‘+’ button
to increase the temperature, or the ‘-‘ button to
decrease it.
NOTE: The temperature will increase or decrease
by increments of 1 degree, from a minimum of 5 to a
maximum of 35 degrees.
NOTE: The temperature can only be manually
selected when the unit is in heating mode; in cooling
mode, temperature selection is automatic and the
temperature level cannot be adjusted.
Intelligent Mode
♦ This unit is complete with an intelligent heating
mode. In this mode, the unit will automatically
detect room temperature and adjust its settings
accordingly, as follows:
♦ Whenever room temperature is more than 2
degrees lower than the control temperature set in
the unit, the unit will automatically default to the
Medium heat setting.
♦ Whenever the ambient temperature is within 2
degrees of the set control temperature, the unit
will default to the Low heat setting.
♦ Whenever the ambient temperature is lower
than the set control temperature, the unit will
automatically stop heating.
NOTE: The unit will automatically default to
Intelligent mode whenever it is rst turned on. The
corresponding indicator will light up on the unit’s LED
display to show this mode is activated. To select this
mode when any other heating or cooling mode is
active, press the ‘Mode’ button on the remote control
or the unit’s control panel until the corresponding
indicator lights up on the unit’s LED display.
♦ Press the ‘-’ and ‘+’ keys on the remote control or
the unit’s control panel when in Intelligent mode to
change the control temperature for this setting.
Setting the Timer
♦ The unit is equipped with a programmable 24 hour
timer.
♦ Press the Timer button on the remote control or
the unit’s control panel to activate the timer.
♦ Once the timer has been activated, press the ‘+’
and ‘-‘ buttons on the remote control or the unit’s
control panel to pre-set the duration of the heating
cycle, from 0 to 24 hours. Press the ‘+’ button to
increase the length of the timed heating cycle, or
the ‘-‘ button to decrease it.
NOTE: The length of the timed cycle will increase
or decrease by increments of 1 hour, from 0 up to
24 hours.
Oscillation
♦ This heater is equipped with an oscillation
function.
♦ To activate the oscillation function, press the
Oscillation button on the remote control or the
unit’s control panel. The corresponding indicator
will light up to show the oscillation function has
been selected.
♦ Press the Oscillation button again while the
function is in operation to turn it off.
The Child Lock Function
♦ This unit is equipped with a programmable child
lock, which provides added safety when the
heater is in use.
♦ To activate the child lock function, simultaneously
press and hold the - and + buttons on the remote
control or the unit’s control panel. There will be a
sound prompt and the unit will no longer respond
to button presses to indicate the child-lock
function has been activated.
♦ To remove the child lock once it has been
activated, simultaneously press and hold the
- and + buttons on the remote control or the
unit’s control panel again while this function is in
operation. There will be a sound prompt and the
unit will resume normal functionality to indicate the
child-lock function has been de-activated.
NOTE: The unit can be put into Standby mode
while the child lock function is activated, but
cannot be turned on again until this function has
been cancelled. However, the child lock can be

ENGLISH
(Original instructions)
9
de-activated even after the unit has been put into
Standby mode. Carry out the process detailed above
after the unit has been powered down to de-activate
the child lock function while in Standby mode. There
will be a sound prompt to indicate the child-lock
function has been de-activated.
Safety Cut-Out
♦ This unit is equipped with a safety cut-out device,
which will automatically kick in whenever the unit
overheats or is tipped over.
♦ The safety cut-out device will activate whenever
the unit reaches an inner working temperature
of more than 50 degrees Centigrade. When this
function activates, the unit will automatically shut
down, and the text ‘FF’ will ash on the unit’s LED
display to show the safety cut-out has activated.
NOTE: While the safety cut-out is in operation, the
unit will not respond to any commands or button
presses. The unit will need to be switched off or
unplugged from the mains before normal operation
can resume.
Tip-Over Switch
♦ In addition to the safety cut-out, this unit is
also complete with a tip-over switch, which will
interrupt operation whenever the heater is tipped
off-balance or toppled over. This function will
automatically activate regardless of if the unit is
turned on or off.
♦ When the safety switch activates, the unit will
automatically stop operating and the text ‘E3’ will
appear on the LED display.
NOTE: When the safety tip-over switch is active,
the unit will not respond to any commands or button
presses. The unit will need to be set back upright,
switched off or unplugged from the mains before
normal operation can resume.
Cleaning and maintenance
WARNING: Before cleaning and maintenance,
switch the appliance off and remove the plug from
the socket, to prevent electric shock.
♦ Do not immerse any part of the appliance, power
cord or plug in liquids.
♦ Use a soft damp cloth to wipe the surface. Avoid
using detergent, spray or chemicals as these may
cause damage to the appliance.
Removable Filter
♦ This unit is equipped with a removable and
washable lter.
♦ To clean the lter, start by removing it from its slot
at the back of the unit. To do this, press the tab at
the top of the lter to loosen it, then pull it away
from the main body of the unit.
♦ Once the lter has been removed, simply rinse
it under running water to clean it, then leave it to
air dry.
NOTE: Ensure the lter is thoroughly dry before
replacing it into the unit.
♦ When the lter has fully dried off, push it back
into its slot at the back of the unit until it clicks into
place.
Mains plug replacement
If a new mains plug needs to be tted:
♦ Safely dispose of the old plug.
♦ Connect the brown lead to the live terminal in the
new plug.
♦ Connect the blue lead to the neutral terminal.
♦ If the product is class I (earthed), connect the
green/yellow lead to the earth terminal.
Note! If your product is class II double insulated
(only 2 wires in the cord set), no connection is to be
made to the earth terminal.
Follow the tting instructions supplied with good
quality plugs. Any replacement fuse must be of the
same rating as the original fuse supplied with the
product.
WARNING: The above section on mains plug
replacement is for authorized service centre
persons.

ENGLISH (Original instructions)
10
Protecting the environment
Separate collection. Products and
batteries marked with this symbol must
not be disposed of with normal household
waste.
Products and batteries contain materials that can
be recovered or recycled, reducing demand for
raw materials. Please recycle electrical products
and batteries according to local provisions. Further
information is available at www.2helpU.com.
Technical data
BXSH44004GB
Input voltage V AC 220 - 240
Frequency Hz 50
Power input W2200
Weight KG 8.55
Product Guarantee
This product comes with a 2 Year guarantee from the
original date of purchase. If any defect arises due to
faulty materials of workmanship, the faulty products
must be returned to the place of purchase. Refund or
replacement is at the discretion of the retailer. This
guarantee is in addition to and in no way prejudices
your statutory rights.
The Following Conditions Apply:
♦ The product must be returned to the retailer
with proof of purchase or a receipt within the
1st year of purchase. For any product related
issues after 12 months please contact our
customer services team.
♦ The product must be installed and used in
accordance with the instructions contained in
this instruction guide.
♦ It must be used only for domestic purposes.
♦ It does not cover wear and tear, damage,
misuse or consumable parts.
♦ This guarantee is valid in the UK and Republic
of Ireland.
For all customer service enquires please contact
us below;
RKW,
Sutton House,
Berry Hill Road,
Stoke-on-Trent,
ST4 2NL
Email [e-mail]
Tel [phone]

11
Model Identier(s): BXSH44004GB
Item Symbol Value Unit Item Unit
Heat Output Type of heat input for electric storage, local space
heaters only (select one)
Nominal heat
output Pnom 2.2 kW Manual heat charge with integrated thermostat No
Minimum heat
output (indicative) Pmin 1.2 kW Manual heat charge control with room and/or outdoor temperature feedback No
Maximum
continuous heat
output Pmax, c 2.2 kW Electronic heat charge control with room
and/or outdoor temperature feedback No
Auxiliary electricity
consumption Fan assisted heat output No
At nominal heat
output elmax 2.2 kW Type of heat output/room temperature control (select one)
At minimum heat
output elmin 1.2 kW Single stage heat output and no room temperature control No
In standby mode eISB 0.0004
2kW Two or more manual stages, no room
temperature control No
Heat output With mechanic thermostat room
temperature control No
Nominal heat
output Pnom 2.3
240V kW With electronic room temperature control Yes
Minimum heat
output (indicative) Pmin 1.2 kW Electronic room temperature control plus day timer No
Maximum
continuous heat
output Pmax, c 2.3 kW Electronic room temperature control plus
week timer No
Auxiliary electricity
consumption Other control options (multiple selections possible)
Nominal heat
output elmax 2.3 kW Room temperature control with presence detection No
Minimum heat
output (indicative) elmin 1.2 kW Room temperature control with open window detection No
In standby mode eISB 0.0004
2kW With distance control option No
With adaptive start control No
With working time limitation No
With black bulb sensor No
Contact Details: Imported by Black & Decker, 210 Bath Road, Slough, Berkshire SL1 3YD

United Kingdom & Black & Decker Tel. [phone]
Republic Of Ireland 210 Bath Road Fax [phone]
www.blackanddecker.co.uk Slough, Berkshire SL1 3YD
emeaser[email protected]
08/2019