Black Box LT7002A User manual

Add two Token Ring workstations
to a lobe—without an extra MAU port.
Add two Token Ring workstations
to a lobe—without an extra MAU port.
2-Port Hub
© 2007. All rights reserved. Black Box Corporation.
FREE 24-hour Tech Support: 724-746-5500
blackbox.com

2 of 3
FEATURES
• Connect two workstations to one lobe.
• No extra MAU port needed.
• Hot-swappable. No downtime.
• Nonpowered— no external power
supplies required.
• Two models to choose from.
• Easily wallmounted with
the included bracket.
OVERVIEW
The 2-Port Hub makes expanding your legacy Token Ring
network fast and easy by enabling you to double the capacity
of a single lobe—even when an extra MAU port isn’t
available.
You can add or delete workstations without shutting down
your network, so you can move equipment while keeping
your LAN up and running and without the extra MAU—or
extra expense—of a backup ring.
Install the hub in just two easy steps. First, use a patch
cable to connect the hub’s ring port to your existing Token
Ring outlet. Then connect two workstations to Ports 1 and 2
of the hub. Because the hub is a nonpowered, passive device,
there’s no need to plug it into a power outlet.
The 2-Port Hub supports Type 3 Token Ring with unshiel-
ded RJ-45 connections for Type 3 unshielded twisted-pair cable
or with shielded RJ-45 connections for Type 3 shielded twisted-
pair cable.
The compact 2-Port Hub can be mounted on a wall with
the included bracket, so you can add workstations anywhere
you need them.
4/25/07
#15389
724-746-5500 blackbox.com
TECH SPECS
Speed — 16 or 4 Mbps
Connectors — LT7001A: (3) Unshielded RJ-45;
LT7002A: (3) Shielded RJ-45
Indicators — LEDs: (2) Port Status (1 per port)
Power — Nonpowered
Size — 1.8"H x 6.5"W x 1"D (4.6 x 16.5 x 2.5 cm)
Weight — 0.5 lb. (0.2 kg)
Item Code
2-Port Hub
Type 3 Unshielded LT7001A
Type 3 Shielded LT7002A
To connect your Token Ring network to Ethernet, order…
Ethernet to Token Ring Adapters (Device to Network)
TCP/IP Protocol for U.S. and U.K. LBU9001-US
SPX (Novell) Protocol for U.S. and U.K. LBU9002-US
Recognize any of these situations?
• You wait more than 30 minutes to get through
to a vendor’s tech support.
• The so-called “tech” can’t help you or gives you
the wrong answer.
• You don’t have a purchase order number and the
tech refuses to help you.
• It’s 9 p. m. and you need help, but your vendor’s
tech support line is closed.
According to a survey by Data Communications
magazine, 90% of network managers surveyed say
that getting the technical support they need is extremely
important when choosing a vendor. But even though
network managers pay anywhere from 10 to 20% of their
overall purchase price for a basic service and support
contract, the technical support and service they receive falls
far short of their expectations—and certainly isn’t worth
what they paid.
At Black Box, we guarantee the best value and the
best support. You can even consult our Technical Support
Experts before you buy if you need help selecting just
the right component for your application.
Don’t waste time and money—call Black Box today.
Why Buy From Black Box? Exceptional Value.
Exceptional Tech Support. Period.
LT7001A

3 of 3
4/25/07
#15389
724-746-5500 blackbox.com
About Token Ring.
Token Ring was developed in the early 1980s by IBM
®
. In
1985, the IEEE released document number 802.5, which formally
accepted Token Ring as a standard. Although its popularity has
been eclipsed by Ethernet, Token Ring is nonetheless a robust
networking standard and is still operating reliably in many
legacy networks.
Token Ring is most often used in IBM mainframe environ-
ments. IBM provides Token Ring connections on much of its
mainframe computer hardware, and its software enables PCs
and mainframes to act as peers on the same network.
The name “Token Ring“ is somewhat misleading. Although
its name implies a physical ring shape, Token Ring is actually a
star-based topology. Logically, the network operates as a ring—
“tokens“ bearing information are passed from node to node
until the token travels completely around the ring.
Token Ring networks are interconnected via passive and
active hubs called Multistation Access Units (MAUs). MAUs are
the fail-safe components of Token Ring networks. If a cable or
a connection goes bad, the MAU will drop that node from the
ring. This fail-safe hub arrangement prevents a break from
taking down the entire network. Ring-in/ring-out ports in each
MAU can be used to connect a ring to other rings.
Token Ring repeaters are used to extend distances within a
ring. Repeaters can increase either main-ring or lobe lengths in
a Token Ring LAN. The main-ring length is the distance between
MAUs. The lobe length is the distance from MAU to workstation.
Token Ring cabling.
The original Token Ring specifications called for shielded
twisted-pair (STP) cable using either a DB9 connector or a unique
square connector called the IBM data connector. Later, Token
Ring was adapted to use conventional unshielded twisted-pair
(UTP) cable with RJ-45 connectors. The most common kinds of
Token Ring cabling in use to day are Type 1 and Type 6 STP as
well as Type 3 UTP.
Type 1 shielded twisted-pair (STP) cable is the original wiring
for Token Ring. In Type 1 cabling, each wire is constructed of 22
AWG solid copper. Type 1 cable is not as flexible as Type 6 cable
and is generally used for long runs in areas where twists and
turns are less likely, such as in walls or conduits.
Type 6 Token Ring cable is a lighter, more pliable version of
Type 1 cable. It’s constructed of two stranded 26 AWG copper
pairs that are surrounded by an overall braided shield. Type 6
cable is commonly used in offices and open areas, and its flexible
construction enables it to negotiate multiple twists and turns.
Type 3 or UTP Token Ring cabling uses the same twisted-pair
CAT3, CAT5, or CAT5e cabling with RJ-45 connectors as 10BASE-T
Ethernet.
Technically Speaking
Attaching older Type 1 Token Ring to UTP Token Ring
requires a balun or adapter.
Two speeds.
Token Ring operates at either 4 or 16 Mbps. While you can
mix speeds within one network, each individual ring can operate
at just one speed. Simply put, you cannot have 4- and 16-Mbps
devices operating in one ring.
Migrating from Token Ring to Ethernet.
Although it’s proven to be reliable and fault-tolerant, Token
Ring has largely been supplanted by Ethernet, and Token Ring
network devices are no longer widely available. Additionally,
Ethernet LANs are less expensive to build and operate than
Token Ring, Ethernet can provide far greater bandwidth, and
many networking products simply do not support Token Ring
at all. The reality is that Token Ring is dying. Even IBM has
walked away from this standard.
For these reasons, system administrators usually choose to
migrate their legacy Token Ring networks to Ethernet by adding
new network segments as Ethernet rather than Token Ring.
There are three different ways to move from Token Ring
to Ethernet by interconnecting the networks. The method you
choose depends on whether you’re connecting a LAN or a WAN
and how much you want to spend.
Keep in mind that no matter how you connect the two net-
works, they both must use the same protocol. In other words,
they must speak the same language, such as IP or IPX
™
.
An economical way to combine Novell
®
IPX based Token Ring
and Ethernet networks is to have them share a server. Just install
either a Token Ring NIC in the Ethernet server or an Ethernet
NIC in the Token Ring server. Then change the server’s config-
uration to enable the internal router program. While this
method is low cost, it adds traffic and overhead to the server,
which can decrease overall network performance.
An easy, standalone hardware solution is to simply use an
Ethernet to Token Ring bridge such as a BLACK BOX
®
Ethernet
to Token Ring Adapter (LBU9001-US, LBU9002-US). Just connect
the bridge to your Token Ring MAU and your Ethernet hub and
make sure that both networks have the same network
identification—in essence, they will become one logical
network. Also, since this is a solution for LANs, both networks
must be close to each other.
Another choice for connecting Token Ring and Ethernet is to
use a router to connect the two networks over a wide-area link.
The router enables each network to maintain its own unique
network identifier.