Black Horse Model Arrow 3D Owner's manual

Instruction Manual book

SPECIFICATION

MadeinVietnam.



Wingspan : 1,290mm 51 in.



Length : 1,190mm 46.85in.



Weight : 0.85kg 1.87Lbs.



Partslisting required(not included).



Battery: 3CELLS-LI-POLY-11.1V-2000mA.h.



Electricmotor :AXI2808/24.



Radio : 04 channels.



Servo : 05p servos.



Propeller : 11x 3.8.



Speed control : 30A.

ARROW 3D Instruction Manual.

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your ARROW 3D . Use the parts listing below to

identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedtohelp the newpilotonhiswaytosuccessful R/C flight.Theywillalsobeable

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modellingknife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

Some more parts.

HARDWARE PACK

COWLING.

Landing gear.....

To avoid scratching your newairplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the

aircraftandto protect the table. Keepacouple

of jars or bowls handy to hold the small parts

after you open the bag.

Pleasetrialfitall the parts.Makesureyouhave

the correct parts and that they fit and are

alignedproperlybeforegluing!Thiswillassure

proper assembly. ARROW 3D ARF is hand

made from natural materials, every plane is

unique and minor adjustments may have to

be made. However, you should find the fit

superior and assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the

following: paint thinner, C/A glue accelerator,

C/A glue debonder and acetone. Do not let

these chemicals come in contact with the

colors on the covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage.

WING ASSEMBLY

(1) Right wing half with pre-installed

aileron.

(1) Left wing half with pre-installed

aileron.

Tail section assembly

(1) Vertical stabilizer with pre-

installedrudder.

(1) Horizontal stabilizer with pre-

installedelevatorhalves.

SUGGESTION.

NOTE.

ARROW 3D INSTRUCTION MANUAL.

+ This is not a toy

+ Be sure that no other flyers are using your

radio frequency.

+ The glow plug clip must be securely

attached to the glow plug.

+ Do not flip the propeller with your fingers.

+ Keep loose clothing and wires away from

thepropeller.

+ Do not start the engine if people are near.

Donot stand in linewiththe side ofthepropel-

ler.

+ Make engine adjustments from behind the

propeller only. Do not reach around the

spinningpropeller.

SAFETY PRECAUTION. INSTALLING THEAILERON SERVOS.

C/Aglue

REPLACEMENT LARGE PARTS

B. Right wing panel.

D. Fuselage.

E. Horizon stabilizer.

F. Vertical stabilizer.

C. Left wing panel.

A. Cowling.

REPLACEMENT SMALL PARTS

G. Decal sheet.

A B

G E

Bottom side

C/Aglue

Tposide

ARROW 3D Instruction Manual.

 1) Install the rubber grommets and brass

eyelets onto the aileron servo.

 3)Turnthe wingpanelright sideup.

Using a modeling knife, remove the covering

at servo tray.

 2) Install the metal connector onto servo

arm .

Remove

covering

 5) Drill1,6mm pilotholesthroughtheblock

of wood for each of the four mounting screws

provided with the servo.

 4) Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out,

remove the masking tape and the servo lead

from the thread.

Electric wire.

 5) Attach the micro control connector to

the servo arms. Be sure to use the lock tie but

it could free rotation.

Micro control connector.

C/Aglue.

Finishing

ARROW 3D INSTRUCTION MANUAL.

Repeat the procedure for the other

wing half.

INSTALLING THE AILERON

CONTROL HORN.

Insert aileron control horn to the aileron.

aileron control horn.

C/Aglue

Secure

Cut

Aileron

controlhorn

Remove

covering

Controlhornslot.

Removecoveringonto the aileroncontrolhorn

pre-cut slot-mounting.

Aileron control horn slot.

ARROW 3D Instruction Manual.

Repeat the procedure for the other

wing half.

INSTALLING ELECTRIC MOTOR.

See pictures below:

 1) Slide the cowl over the motor and line

up the back edge of the cowl with the marks

you made on the fuselage.

Secure

COWLING.

ARROW 3D INSTRUCTION MANUAL.

2) While keeping the back edge of the

cowl flush with the marks, align the front of

thecowl with the crankshaft of themotor. The

front of the cowl should be positioned so the

crankshaft is in nearly the middle of the cowl

opening. Hold the cowl firmly in place using

pieces of masking tape.

3) Slide the cowl back over the motor.

Machine

screw.

3 x 10mm

 1) Install the rubber grommets and brass

eyelets onto the aileron servo.

 2) Install the metal connector onto servo

arm .

SERVO INSTALLATION.

Remove covering

Rightside of thefuselage

 4) Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out,

remove the masking tape and the servo lead

from the thread.

 3) Usingamodeling knife, remove the

covering at servo tray.

Remove covering

Leftside of thefuselage

ARROW 3D Instruction Manual.

 5) Drill1,6mm pilotholesthroughtheblock

of wood for each of the four mounting screws

provided with the servo.

Repeat the procedure for the other

servo.

INSTALLING ELEVATOR.

Right side

Left side

C/Aglue

Center line

 1) Using a modeling knife, remove the

covering at fuselage slot.

Remove covering

 2) Using a ruler and a pen, locate the

centerline of the horizontal stabilizer, at the

trailing edge and place a mark. Use a triangle

and extend this mark, from back to front,

across the top of the stabilizer. Also extend

thismark down theback of the trailing edge of

the stabilizer.

 3) Slide the the horizontal fin without el-

evator into place in the pre-cut slot in the rear

of the fuselage.

Markline

Top

ARROW 3D INSTRUCTION MANUAL.

 5) Remove the stabilizer. Using the lines

youjust drew asa guide, carefully removethe

coveringfrombetweenthemusinga modeling

knife.

 4) With the stabilizer held firmly in place,

use a pen and draw lines onto the stabilizer

where it and the fuselage sides meet. Do this

on both the right and left sides and top and

bottom of the stabilizer.

 6) Slide the horizontal fin into place in the

pre-cut slot in the rear of the fuselage again.

Remove covering.

Bottom Top

C/Aglue

Bottom

C/Aglue

When cutting through the covering to re-

move it, cut with only enough pressure

toonly cut through the coveringitself. Cutting

into the balsa structure may weaken it.

ARROW 3D Instruction Manual.

See pictures below:

CONTROL HORN INSTALLATION.

Removecovering

C/A glue

elevator control horn.

INSTALLING THE ELEVATOR PUSHROD.

Pushrod install as same as method of ai-

leron wing. See pictures below:

elevator pushrod wire

C/A glue

Top side

 7) When you are sure that everything is

aligned correctly, mix up a generous amount

ofFlash30 Minute Epoxy.Apply a thin layerto

the top and bottom of the stabilizer mounting

platform sides in the fuselage. Slide the

stabilizer in place and realign. Double check

all of your measurements once more before

the epoxy cures. Hold the stabilizer in place

with T-pins or masking tape and remove any

excessepoxyusingapapertowelandrubbing

alcohol.

Removecoveringonto the aileroncontrolhorn

pre-cut slot-mounting.

Other manuals for Arrow 3D

Table of contents

Other Black Horse Model Toy manuals

Black Horse Model

Black Horse Model MINIMOA Owner's manual

Black Horse Model

Black Horse Model Twister Owner's manual

Black Horse Model

Black Horse Model AT.6-Texan Owner's manual

Black Horse Model

Black Horse Model Cobra Owner's manual

Black Horse Model

Black Horse Model PIPER CUB NC 76510 Owner's manual

Black Horse Model

Black Horse Model BIRD DOG Owner's manual

Black Horse Model

Black Horse Model BH180 Owner's manual

Black Horse Model

Black Horse Model SBACH 342 Owner's manual

Black Horse Model

Black Horse Model SEA FURY BH148 Owner's manual

Black Horse Model

Black Horse Model Spitfire MK Owner's manual

Black Horse Model

Black Horse Model SUPER DECATHLON Owner's manual

Black Horse Model

Black Horse Model YAK 54 Owner's manual

Black Horse Model

Black Horse Model EXTRA 300 Owner's manual

Black Horse Model

Black Horse Model BH48 Owner's manual

Black Horse Model

Black Horse Model Pitts BH85-A User manual

Black Horse Model

Black Horse Model L-13 Blanik User manual

Black Horse Model

Black Horse Model TURBO BEAVER BH162 Owner's manual

Black Horse Model

Black Horse Model LF-107 Lunak Owner's manual

Black Horse Model

Black Horse Model GIL MORE Owner's manual

Black Horse Model

Black Horse Model Blade BH 70 Owner's manual

Black Horse Model

Black Horse Model NOORDUYN NORSEMAN Owner's manual

Black Horse Model

Black Horse Model BH167 Owner's manual

Black Horse Model

Black Horse Model Harmon Rocket BH100 Owner's manual

Black Horse Model

Black Horse Model PZL-104 WILGA BH 124 Owner's manual

Popular Toy manuals by other brands

marklin

marklin 37321 instruction manual

Canon

Canon PAPER CRAFT Assembly instructions

GREAT PLANES

GREAT PLANES Pitts M-12S instruction manual

NOCH

NOCH 14261 manual

Hausler

Hausler 450 SE V2 quick start

Dynaflite

Dynaflite Daydream instruction manual

Kenner

Kenner Batman 63651 instructions

LEGO

LEGO 8527 instructions

Multiplex

Multiplex EasyStar II Building instructions

iKarus

iKarus ECO 8 Assembly instruction

Walkera

Walkera 38 User handbook

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE manual

MD MXION SWD user manual

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway instructions

marklin

marklin 39671 user manual

LEGO

LEGO TECHNIC 8735 instructions

Mattel

Mattel HOTWHEELS DWL04 instructions

REVELL

REVELL Bristol Beaufighter TF.X Assembly manual