Black Horse Model Fieseler Fi156C STORCH Owner's manual

SPECIFICATION


Wingspan : 2,850 mm 112.20 in.


Length : 1,910 mm 75.20 in.
Parts listing required (not included).


Weight : 8.1 kg 17.82 Lbs.


Radio : 06 channels.


Servo : 08 servos standard high torque servos.


Engine : 35 CC gas(FUJI IMVAC).
Instruction Manual book
MadeinVietnam.
ITEMCODE:BH99.

2
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your FIESELER Fi156C STORCH. Use the parts
listing below to identify all parts.
WARNING
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
proceduresdesignedtohelpthenew pilotonhiswaytosuccessfulR/C flight.Theywillalsobeable
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modellingknife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
COWLING.
Landinggear.....
Toavoid scratching yournew airplane,do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper, both to protect the air-
craftand toprotectthetable.Keepacoupleof
jars or bowls handy to hold the small parts af-
ter you open the bag.
Pleasetrialfitall theparts. Makesureyouhave
the correct parts and that they fit and are
alignedproperly beforegluing!Thiswill assure
proper assembly. FIESELER Fi156C STORCH
ARF is hand made from natural materials,
every plane is unique and minor adjustments
may have to be made. However, you should
find the fit superior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the follow-
ing:paintthinner,C/Aglueaccelerator,C/Aglue
debonderandacetone.Donotletthesechemi-
cals come in contact with the colors on the
covering and the plastic parts.
PARTS LISTING
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installedrudder.
(1) Horizontal stabilizer with pre-
installedelevator halves.
SUGGESTION
NOTE.

3
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual
Caution: this model is not a toy!
If you are a beginner to this type of powered
model,please askan experiencedmodel flyer
forhelpand support.If youattempt to operate
themodel withoutknowing whatyouaredoing
you could easily injure yourself or somebody
else. Please keep your safety and well-being
in mind at all times.
Important: before you start construction
Even if you have already built a large number
ofRCmodels pleaseread rightthroughthese
instructions and check all the kit components
against the parts list. We have taken great
trouble to keep construction as simple as
possible, without making any compromises
in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the
film covering due to major fluctuations in
weather conditions (temperature, humidity
etc.); in rare cases you may even find a slight
warp in a component. These minor faults are
in the nature of film-covered built-up wooden
structures, and can easily be corrected using
a heat gun, as commonly used for modelling.
Caution! do not heat the film more than is
absolutely necessary. If the air or the iron is
too hot, the film may melt and holes may be
formed.
This model is highly pre-fabricated and can
bebuilt inaveryshorttime. However,the work
which you have to carry out is important and
must be done carefully. The model will only
be strong and fly well if you complete your
taskscompetently -so pleaseworkslowlyand
accurately.
When self-tapping screws have to be
screwed into wood, apply a little white glue
to prevent them shaking loose: just squirt
white glue into the hole and fit the screw.
+ This is not a toy
+ Be sure that no other flyers are using your
radio frequency.
+ Do not smoke near fuel
+ Store fuel in a cool, dry place, away from
children and pets.
+ Wear safety glasses.
+Theglowplug clipmust besecurelyattached
to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from
thepropeller.
+ Do not start the engine if people are near.
Donotstandinlinewiththesideof thepropel-
ler.
+ Make engine adjustments from behind the
propeller only. Do not reach around the spin-
ningpropeller.
SAFETY PRECAUTION.
REPLACEMENT LARGE PARTS
Creases: Blowwarm airover thearea
and rub down with a soft
cloth.
Wing warp: Holdthepaneltwistedgently
in the opposite direction to
the warp, and apply warm
air to remove the creases
from the covering.
B.Wing panel (B1&B2)
C.Fuselage.
D.Horizontal stabilizer(D1&D2). F. Aluminiumwing dihedralbrace.
E. Rudder
G. Decal sheets.
C
D2 G
A
B1
B2
F
D1
E
A.Cowling.

4
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual
REPLACEMENT SMALL PARTS
2.FuelTank.
4.Plasticpartsforrudderpushrod.
1.Wheels.
5.Landinggearstruts.
3.Ruler wing.
7.Tailgearset.
6.Wingstrutsset.
8.Verticalstabilizerstruts.
5e.
5F.
5d.
5c.
5a.
5b.
6a.
6b.
6c. 6d.
1. 2.
3. 4.
6. 5.
7.
8.
I. AILERON.
1) Install the rubber grommets and brass
eyelets onto the aileron servos.
1.INSTALLING THE AILERON SERVOS.
2)Using amodeling knife,remove thecov-
ering at possition show below.
Bottom side Aileron
Flap
Remove
covering.

5
FIESELER Fi156C STORCH - ITEM CODE: BH99. Instruction Manual
4)Drill1,6mmpilotholes throughthe block
of wood for each of the four mounting screws
provided with the servo.
3) Using the thread as a guide and using
masking tape, tape the servo lead to the end
of the thread: carefully pull the thread out.
When you have pulled the servo lead out, re-
move the masking tape and the servo lead
from the thread.
5. Instal servo tray with aileron servo into
the wing as same as picture below.
Installaileron controlhornas sameas
picturebelow.
Electric wire
Thread Aileron
Flap
Repeat the procedure for the other wing
half.
2x12mm.
Secure
Secure
INSTALLINGTHEAILERON CONTROL HORN
.
3 x 20 mm.
Elevator
control horn