Black Horse Model Thermal 3.0 Owner's manual

SPECIFICATION



Wingspan : 3,000 mm 118.1 in.



Length : 1,600 mm 62.99 in.



Weight : 2.2 kg 4.84 Lbs.

Partslistingrequired(notincluded).



Radio : 05 channels.



Servo : 06 mini servos



ElectricMotor:BOOST40



Battery:3Cell-LiPoly-11.1V-3250-4250mAh.

MadeinVietnam.

Item code:BH131

Instruction Manual book

THERMAL 3.0-Item code:BH131. Instruction Manual

This instruction manual is designed to help you build a great flying aeroplane. Please read this

manual thoroughly before starting assembly of your Thermal 3.0. Use the parts listing below to

identify all parts.

WARNING.

Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is

capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU

ASSUME ALL RISK & RESPONSIBILITY.

IfyouareinexperiencedwithbasicR/CflightwestronglyrecommendyoucontactyourR/Csupplier

and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training

proceduresdesignedtohelpthenewpilotonhiswaytosuccessfulR/Cflight.Theywillalsobeable

to advise on any insurance and safety regulations that may apply.

TOOLS & SUPPLIES NEEDED.

Thick cyanoacrylate glue.

30 minute epoxy.

5 minute epoxy.

Hand or electric drill.

Assorted drill bits.

Modellingknife.

Straight edge ruler.

2mm ball driver.

Phillips head screwdriver.

220 grit sandpaper.

90° square or builder’s triangle.

Wire cutters.

Masking tape & T-pins.

Thread-lock.

Paper towels.

Some more parts.

HARDWAREPACK

Landinggear.....

Toavoid scratching your new airplane, do not

unwrap the pieces until they are needed for

assembly. Cover your workbench with an old

towel or brown paper, both to protect the air-

craftand to protect the table. Keep a coupleof

jars or bowls handy to hold the small parts af-

ter you open the bag.

Pleasetrialfitalltheparts.Makesureyouhave

the correct parts and that they fit and are

alignedproperly beforegluing!This willassure

proper assembly.Thermal 3.0 ARF is hand

made from natural materials, every plane is

unique and minor adjustments may have to

be made. However, you should find the fit su-

perior and assembly simple.

The painted and plastic parts used in this kit

are fuel proof. However, they are not tolerant

of many harsh chemicals including the follow-

ing:paintthinner,C/Aglueaccelerator,C/Aglue

debonderandacetone. Donot letthese chemi-

cals come in contact with the colors on the

covering and the plastic parts.

PARTS LISTING.

FUSELAGE ASSEMBLY

(1) Fuselage.

WING ASSEMBLY

(1) Right wing half with pre-installed

aileron.

(1) Left wing half with pre-installed

aileron.

Tail section assembly

(1) Vertical stabilizer with pre-

installedrudder.

(1) Horizontal stabilizer with pre-

installedelevator halves.

SUGGESTION.

NOTE.

THERMAL 3.0-Item code:BH131. Instruction Manual

Caution: this model is not a toy!

If you are a beginner to this type of powered

model,please ask an experienced model flyer

forhelpandsupport.Ifyou attempt to operate

themodel without knowingwhatyou are doing

you could easily injure yourself or somebody

else. Please keep your safety and well-being

in mind at all times.

Important: before you start construction

Even if you have already built a large number

ofRCmodels please read right through these

instructions and check all the kit components

against the parts list. We have taken great

trouble to keep construction as simple as

possible, without making any compromises

in the area of safety.

Note regarding the film covering

Minor creases or bubbles may develop in the

film covering due to major fluctuations in

weather conditions (temperature, humidity

etc.); in rare cases you may even find a slight

warp in a component. These minor faults are

in the nature of film-covered built-up wooden

structures, and can easily be corrected using

a heat gun, as commonly used for modelling.

Caution! do not heat the film more than is

absolutely necessary. If the air or the iron is

too hot, the film may melt and holes may be

formed.

This model is highly pre-fabricated and can

bebuilt inavery short time.However, the work

which you have to carry out is important and

must be done carefully. The model will only

be strong and fly well if you complete your

taskscompetently - sopleasework slowly and

accurately.

When self-tapping screws have to be

screwed into wood, apply a little white glue

to prevent them shaking loose: just squirt

white glue into the hole and fit the screw.

Creases: Blowwarm air over the area

and rub down with a soft

cloth.

SAFETY PRECAUTION.

Wing warp: Holdthepaneltwisted gently

in the opposite direction to

the warp, and apply warm

air to remove the creases

from the covering.

REPLACEMENT LARGE PARTS

3.Left & Right Stabilizer 6.Carbon tube horizontal stabilizer.

2.Wings panel(Left,Right).

1. Fuselage. 7. Decal sheet

5. Carbon tube wing

4. Rudder

+ This is not a toy

+ Be sure that no other flyers are using your

radio frequency.

+ Wear safety glasses.

+ Keep loose clothing and wires away from

thepropeller.

+ Do not start the motor if people are near.

Donot stand in line with the side of the propel-

ler.

+ Make motor adjustments from behind the

propeller only. Do not reach around the spin-

ningpropeller.

THERMAL 3.0-Item code:BH131. Instruction Manual

REPLACEMENT SMALL PARTS

1) Install the rubber grommets and brass

eyelets onto the aileron servos.

I. AILERON.

1.INSTALLING THE AILERON SERVOS.

Top side

Bottom side

Aileron.

Flap.

C/Aglue.

1. Plastic parts of flap pushrod

5. Plastic parts of bottom wing

3. Plastic part of rudder pushrod.

4. Plastic part of bottom tail fuselage.

2. 3.

2.Connectors

THERMAL 3.0-Item code:BH131. Instruction Manual

2. Using a modeling knife, remove the cov-

ering servo tray.

Aileron

servo tray.

Remove the

covering.

C/Aglue.

Bottom side.

Secure.

THERMAL 3.0-Item code:BH131. Instruction Manual

4.Drill 1,5mm pilot holes through the block

of wood for each of the four mounting screws

providedwiththeservo.Install servointoaileron

servo tray as same as picture below.

3) Using the thread as a guide and using

masking tape, tape the servo lead to the end

of the thread: carefully pull the thread out.

When you have pulled the servo lead out, re-

move the masking tape and the servo lead

from the thread.

Electric wire.

Thread.

5. Instal servo tray with aileron servo into

the wing as same as picture below.

2x10mm.

Repeat the procedure for the other wing

half.

A+B Epoxy

PLUS glue

A+B Epoxy

PLUS glue

Aileroncontrolhorn

INSTALLINGTHEAILERON CONTROLHORN.

THERMAL 3.0-Item code:BH131. Instruction Manual

Aileron

control horn

Repeat the procedure for the other wing

half.

Installing the aileron linkages as pictures

below.

INSTALLING THE AILERON

LINKAGES.

Repeat the procedure for the other wing

half.

Aileron.

Flap

II. FLAP SERVO.

1.INSTALLING THE FLAP SERVOS.

M2 lock nut

50 mm M2

M2 lock nut

50 mm M2

THERMAL 3.0-Item code:BH131. Instruction Manual

2x10mm.

Flap controlhorn

A+B Epoxy

PLUS glue

Secure.

Topside

Flap

Bottom side.

2.INSTALLING THE FLAP CONTROL HORN .

THERMAL 3.0-Item code:BH131. Instruction Manual

Plastic parts of flap pushrod .

Plastic parts of bottom wing

Bottom side.

Top side

4x12mm

Secure.

C/Aglue

THERMAL 3.0-Item code:BH131. Instruction Manual

Secure.

3x 10mm

Front view.

INSTALLING THE BATTERY.

See pictures below:

Repeat the procedure for the other wing

half.

See pictures below:

INSTALLING ELECTRIC MOTOR.

Pushout

Front view.

motor

Other manuals for Thermal 3.0

Table of contents

Other Black Horse Model Toy manuals

Black Horse Model

Black Horse Model Liberty 182II User manual

Black Horse Model

Black Horse Model Edge 540-V3 Owner's manual

Black Horse Model

Black Horse Model L-13 Blank User manual

Black Horse Model

Black Horse Model GIL MORE Owner's manual

Black Horse Model

Black Horse Model Tornado BH17 Owner's manual

Black Horse Model

Black Horse Model SPEED AIR BH.08 Owner's manual

Black Horse Model

Black Horse Model Landscape Owner's manual

Black Horse Model

Black Horse Model Edge 540-V3 Owner's manual

Black Horse Model

Black Horse Model Extra S Owner's manual

Black Horse Model

Black Horse Model AT.6-Texan Owner's manual

Black Horse Model

Black Horse Model Blade BH 70 Owner's manual

Black Horse Model

Black Horse Model L-39 Albatros Owner's manual

Black Horse Model

Black Horse Model Sputnik Owner's manual

Black Horse Model

Black Horse Model SBACH 342 Owner's manual

Black Horse Model

Black Horse Model EXTRA 300 Owner's manual

Black Horse Model

Black Horse Model Extra 330L Owner's manual

Black Horse Model

Black Horse Model GLASAIR Owner's manual

Black Horse Model

Black Horse Model Proctor Owner's manual

Black Horse Model

Black Horse Model BH150 Owner's manual

Black Horse Model

Black Horse Model SEA FURY BH148 Owner's manual

Black Horse Model

Black Horse Model SUPER AIR BH.05 User manual

Black Horse Model

Black Horse Model P- 47 THUNDERBOLT- EP Owner's manual

Black Horse Model

Black Horse Model sea fury-ep User manual

Black Horse Model

Black Horse Model Pitts BH85-A User manual

Popular Toy manuals by other brands

marklin

marklin 37321 instruction manual

Canon

Canon PAPER CRAFT Assembly instructions

GREAT PLANES

GREAT PLANES Pitts M-12S instruction manual

NOCH

NOCH 14261 manual

Hausler

Hausler 450 SE V2 quick start

Dynaflite

Dynaflite Daydream instruction manual

Kenner

Kenner Batman 63651 instructions

LEGO

LEGO 8527 instructions

Multiplex

Multiplex EasyStar II Building instructions

iKarus

iKarus ECO 8 Assembly instruction

Walkera

Walkera 38 User handbook

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE manual

MD MXION SWD user manual

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway instructions

marklin

marklin 39671 user manual

LEGO

LEGO TECHNIC 8735 instructions

Mattel

Mattel HOTWHEELS DWL04 instructions

REVELL

REVELL Bristol Beaufighter TF.X Assembly manual