Black Horse Model Mosquito MK VI User manual

SPECIFICATION


 Wingspan : 1,600 mm 62.99 in.


 Length : 1,230 mm 48.43 in.


 Weight : 2.5 kg 5.5 Lbs.


 Radio : 06 channels.


 Servo : 07 servos.


 Electric Motor : ( 02pcs ) AXI 2814/12.


 Battery: 3 CELLS-LI-POLY
11.1V-5000 mA.h-20c.


 Propeller : ( 02pcs )10 x 6


 Speed control : ( 02pcs ) : 40 A.
Instruction Manual book
Made in Vietnam.
ITEMCODE:BH50.

MOSQUITO MK VI. INSTRUCTION MANUAL.
2
This instruction manual is designed to help you build a great flying aeroplane. Please read this
manual thoroughly before starting assembly of your MOSQUITOMKVI. Use the parts listing below
to identify all parts.
WARNING.
Please be aware that this aeroplane is not a toy and if assembled or used incorrectly it is
capable of causing injury to people or property. WHEN YOU FLY THIS AEROPLANE YOU
ASSUME ALL RISK & RESPONSIBILITY.
If you are inexperienced with basic R/C flight we strongly recommend you contact your R/C supplier
and join your local R/C Model Flying Club. R/C Model Flying Clubs offer a variety of training
procedures designed to help the new pilot on his way to successful R/C flight. They will also be able
to advise on any insurance and safety regulations that may apply.
TOOLS & SUPPLIES NEEDED.
Thick cyanoacrylate glue.
30 minute epoxy.
5 minute epoxy.
Hand or electric drill.
Assorted drill bits.
Modelling knife.
Straight edge ruler.
2mm ball driver.
Phillips head screwdriver.
220 grit sandpaper.
90° square or builder’s triangle.
Wire cutters.
Masking tape & T-pins.
Thread-lock.
Paper towels.
Some more parts.
HARDWAREPACK
COWLING.
Landinggear.....
To avoid scratching your new airplane, do not
unwrap the pieces until they are needed for
assembly. Cover your workbench with an old
towel or brown paper , both to protect the
aircraft and to protect the table. Keep a couple
of jars or bowls handy to hold the small parts
after you open the bag.
Please trial fit all the parts. Make sure you have
the correct parts and that they fit and are
aligned properly before gluing! This will assure
proper assembly. MOSQUITO MK VI ARF is
hand made from natural materials, every plane
is unique and minor adjustments may have to
be made. However, you should find the fit su-
perior and assembly simple.
The painted and plastic parts used in this kit
are fuel proof. However, they are not tolerant
of many harsh chemicals including the
following: paint thinner, C/A glue accelerator,
C/A glue debonder and acetone. Do not let
these chemicals come in contact with the
colors on the covering and the plastic parts.
PARTS LISTING.
FUSELAGE ASSEMBLY
(1) Fuselage.
WING ASSEMBLY
(1) Right wing half with pre-installed
aileron.
(1) Left wing half with pre-installed
aileron.
Tail section assembly
(1) Vertical stabilizer with pre-
installed rudder.
(1) Horizontal stabilizer with pre-
installed elevator halves.
SUGGESTION.
NOTE.

MOSQUITO MK VI. INSTRUCTION MANUAL.
3
+ This is not a toy
+ Be sure that no other flyers are using your
radio frequency.
+The glow plug clip must be securely attached
to the glow plug.
+ Do not flip the propeller with your fingers.
+ Keep loose clothing and wires away from
the propeller.
+ Do not st art the motor if people are near .
Do not stand in line with the side of the
propeller.
SAFETY PRECAUTION.
Caution: this model is not a toy!
If you are a beginner to this type of powered
model, please ask an experienced model flyer
for help and support. If you attempt to operate
the model without knowing what you are doing
you could easily injure yourself or somebody
else. Please keep your safety and well-being
in mind at all times.
Important: before you start construction
Even if you have already built a large number
of RC models please read right through these
instructions and check all the kit components
against the parts list. We have taken great
trouble to keep construction as simple as
possible, without making any compromises
in the area of safety.
Note regarding the film covering
Minor creases or bubbles may develop in the
film covering due to major fluctuations in
weather conditions (temperature, humidity
etc.); in rare cases you may even find a slight
warp in a component. These minor faults are
in the nature of film-covered built-up wooden
structures, and can easily be corrected using
a heat gun, as commonly used for modelling.
Creases: Blow warm air over the area
and rub down with a soft
cloth.
Wing warp: Hold the panel twisted
gently in the opposite
direction to the warp, and
apply warm air to remove
the creases from the
covering.
Caution! do not heat the film more than is
absolutely necessary. If the air or the iron is
too hot, the film may melt and holes may be
formed.
This model is highly pre-fabricated and can
be built in a very short time. However
, the work
which you have to carry out is important and
must be done carefully . The model will only
be strong and fly well if you complete your
tasks competently - so please work slowly
and accurately.
When self-tapping screws have to be
screwed into wood, apply a little white
glue to prevent them shaking loose: just
squirt white glue into the hole and fit the
screw.
B. Wing panel.
C. Fuselage. D. Horizontal stabilizer.
E. Vertical stabilizer.
REPLACEMENT LARGE PARTS
REPLACEMENT SMALL PARTS
A
B
D
A. Cowlings.
1. Fiberglass cover first fuselage.
3. Fiberglass cover first wing panel.
5. Retractable landing gear.
2. Wheel (60mm).
G. Aluminium wing dihedral brace.
4. Spinner.
C
E
F
F. Decal sheet.
G
2
1
3 4
6. Tail gear.
5
6

MOSQUITO MK VI. INSTRUCTION MANUAL.
4
 1) Install the rubber grommets and brass
eyelets onto the aileron servo.
2) Install the metal connector onto servo
arm.
INSTALLING THEAILERON - FLAP SERVO
CONTROLHORN.
Bottom side of left wing
Push
C/A glue.
Epoxy glue
INSTALLING THE AILERON - SERVO CONTROL HORN.
C/A glue.
Aileron
C/A glue.
Flap
C/A glue.
Flap

MOSQUITO MK VI. INSTRUCTION MANUAL.
5
Repeat the procedure for the other
wing half.
Epoxy glue.
C/A glue.
C/A glue.
Bottom of left.
Remove covering.
3) Install the aileron servo as same as
picture.

MOSQUITO MK VI. INSTRUCTION MANUAL.
6
4) Attach the micro control connector to
the servo arms. Be sure to use the lock tie but
it could free rotation.
C/A glue.
Micro control
connector.
Insert aileron control horn to the aileron.
-Using a ruler & pen to draw a straight
line as below picture.
Bottom side.
Aileron
Flap
aileron control horn.
Pushrod wire
Flap control horn.
INSTALLINGCONTROL HORN OF THE
AILERON
Tracing a line with your finger and using a
modeling knife remove a (3mm) wide strip on
to the aileron control horn pre-cut slot-mount-
ing.
Aileron control
horn slot
Bottom side
Remove
covering
59mm
Straight line

MOSQUITO MK VI. INSTRUCTION MANUAL.
7
C/A glue.
Secure
aileron control horn.
Aileron
control horn.
Cut
Aileron
Remove covering
Bottom side
Flap
INSTALLINGFLAP SERVO-CONTROLHORN.

MOSQUITO MK VI. INSTRUCTION MANUAL.
8
C/A glue
Flap control horn
Pushrod wire
Remove covering on
pre-cut slot -mounting
flap control horn.
15mm
Cut
Secure
Insert flap control horn as picture above.
Flap
control horn

MOSQUITO MK VI. INSTRUCTION MANUAL.
9
Repeat the procedure for the other
wing half.
INSTALLING ELECTRIC MOTOR.
See pictures below:
3x 15mm.
Secure
Motor mount wood:
Epoxy glue
Bottom side
Aileron
Flap

MOSQUITO MK VI. INSTRUCTION MANUAL.
10

MOSQUITO MK VI. INSTRUCTION MANUAL.
11
INSTALLINGRETRACTABLE
LANDING GEAR.
Remove covering

MOSQUITO MK VI. INSTRUCTION MANUAL.
12
Cut out and reomver the balsa plywood as
picture to place for the retract landing gear
mounts.
Drill a hole 1.5 mm (diameter)
Mark point
Secure
3 mmx 15mm
cut here

MOSQUITO MK VI. INSTRUCTION MANUAL.
13
Secure
3 mmx 15mm
Secure
Install the engine cowling as same as
picture below.
ENGINE NACELLE-COWLING
INTALLATION.
Bottom nacelle
Cowling
Remove covering through balsa wood on to
pre-cut slot of bottom wing as picture below.
Mark point
Bottom side
Pushrod
retract
Bottom side
Top side

MOSQUITO MK VI. INSTRUCTION MANUAL.
14
Secure
3 x 15mm
INSTALLING THE BOTTOM NACELLE
50mm
Center line
Epoxy glue
Center line
Left side

MOSQUITO MK VI. INSTRUCTION MANUAL.
15
C/A glue
Pre-cut slot
Pre-cut slot
Pre-cut slot
Cut
C/A glue
Bottom nacelle

MOSQUITO MK VI. INSTRUCTION MANUAL.
16
Mark line
Left side
Mark line
Left side
Left side
Right side
Mark line
Right side
Right side
Mark line
Right side

MOSQUITO MK VI. INSTRUCTION MANUAL.
17
C/A glue
Push down & push on
Center line
Mark point
11mm
Mark point

MOSQUITO MK VI. INSTRUCTION MANUAL.
18
Secure
Drill a hole with 4mm diameter.
Secure

MOSQUITO MK VI. INSTRUCTION MANUAL.
19
Repeat the procedure for the other
engine cowl.
Another wing halft as same as process.
Install the spinner as same as picture
below.
3 x 12mm.
INSTALLING THE SPINNER
Secure
Bottom side
Top side
Top side
1) Install the rubber grommets and brass
eyelets onto the elevator servo and nose gear
servo.
2) Install the metal connector onto servo
arm.
Servo for retract only
SERVO INSTALLATION.

MOSQUITO MK VI. INSTRUCTION MANUAL.
20
1) Using a modeling knife, cut away the
covering from the fuselage for the stabilizer
and remove it.
2) Draw a center line onto the horizontal
stabilizer. Then put the horizontal into the fu-
selage.
Remove covering
C/A glue
Center line.Top elevator.
HORIZONTALSTABILIZER INSTALLATION.
3) Mark the shape of the vertical on the left
and right sides onto the horizontal stabilizer
using a left-tip pen.
Mark line
Bottom
C/A glue
C/A glue
Top