Nidec PG-35 User manual

1
Instruction ManualVer.9.2
Nishi-ShinjukuPrimeSquare.,7-5-25
Nishi-ShinjukuShinjuku-kuTokyo160-0023,Japan
https://www.nidec-copal-electronics.com
Formoredetailedinformationpleaseaskforthenearest
distributororthefollowingsalescenter.
Thankyouforpurchasinga
NIDECCOPALELECTRONICSCORP.product.
Inordertousetheproductcorrectlyandmost
appropriately,pleasecompletelyreadthismanualbefore
useandkeepitforfuturereference.
SMALLSIZEPRESSUREGAUGE
PG-35／PG-30
ImportantInformationandWarnings
①SelecteitherthePG-30orthePG-35dependinguponthetypeofpressurizedmedia.
②ThemaximumimpressedpressureofthePG-30-102Ratthetimeofvacuumbreakis500kPa.
③Forstability,usearegulateddirectcurrentpowersupply.
Surge absorbing devices (diodes,varistors, etc.) are necessary if inductive loads such as relays or solenoids are connected to the same
circuitasthePG-30/PG-35.
IfusingaDCpowersupplyunitsuchasaswitchingpowersupply,theFGterminalshouldbeearthed.Donotwireinparalleltohigh
tensioncablesorpowerlines,orusecableductswhichcontainhightensioncablesorpowerlines.
④Becarefulnottocrimpanywiresduringhandling,orputanypressureonthedisplayareaofthemainbodywhileassemblingpiping.The
fittingtorqueofsealingscrewsandM5fittingscrewsshouldbe3.0N･mmaximum.
⑤UsepHneutraldetergentstocleanthebody.Donotusesolventssuchasthinners.
⑥This product is dust proof and drip proof (to IP65 of IEC standards) and is not suitable for use in environments requiring higher
standards.
⑦Donotusepointedobjectssuchaspenstopressthesettingbuttonsonthedisplaypanel,asthismaypushholesinthesettingbuttonsand
damagethem.
⑧Donotinsertwires,etc.inthepressureport,asthismaydamagetheinternaldiaphragmandcausemalfunctioning.
⑨PG-35G3/8type:
Do not touch or scratch the diaphragm at the edge of the fitting, as this may alter the performance characteristics or damage the
diaphragm,andcausemalfunctioning.
⑩PG-35gaskettype:
Do not touch or scratch the edge of the fitting, as this may damage the sealing and
causeleakage.
⑪ThePG-30/35seriesdonothavean explosion proofstructure.Donotuseitforthe
detectionofflammablegases.
⑫Whenanalogoutputissuppliedtoanoise-sensitivedevice,alow-passfilterisrequested
inacustomer'scircuit.
⑬Countermeasuresfornoiseinterference.
PleaseconnecttheshieldedwireofthisproducttoFGterminalofthepowerline.（The
shieldwireisconnectedwiththemetalpartinsideoftheproduct.）
marking
（CompliancewithEMCStandards）
Powersupplyunit
Surgeabsorbingcircuit ＋Ｖ
ＦＧ←Theshieldwire
PG30/35
ＦＧ
DCoutputACinput

2
Specifications
FunctionNames
OutputElectricalDiagram （WirecolorscorrespondtoIECstandards）
Model
Type
Ratedpressurerange
Maximumpressure
Break-downpressure
Acceptablemedia
Operatingvoltage
Currentconsumption
Switch
outputs
Outputmode
Outputmode
Analogoutput
Hysteresis
Repeatability
Response
Shortcircuitprotection
Gaugepressure Gaugepressure
LiquidsorgasesthatdonotcorrodeSUS316L
Pressurerange Pin（L）〜Pin（H）
1±0.2V
4±0.2V
Outputvoltageaccuracy Vzero（upper）／Vspan（Lower）
（Vzero：Pin=0、Vspan：Pin=0〜Pin（H））
−100〜100kPa
0〜100kPa
0〜−100kPa
3±0.2V
2±0.2V
1±0.2V
4±0.2V
R
G
V
R
G
V
−100〜1000kPa
0〜1000kPa
1.36±0.2V
3.64±0.2V
3±0.2V
2±0.2V
1±0.2V
4±0.2V
0〜100kPa（abs）
−10〜10kPa
0〜10kPa
0〜−10kPa
−100〜100kPa
0〜100kPa
0〜−100kPa
−100〜1000kPa
0〜1000kPa
1.36±0.2V
3.64±0.2V
Non-corrosivegases
10.8〜30VDC（includingripple）
50mAmaximum
0〜300countssetting（adjustable）
±0.2％FS±1digit
Approx.5ms（DigitalFillter:“F-0”）
Exists
Outputvoltage1〜5V／Pin（L）〜Pin（H）,Outputimpedance：10kΩ,Resolution：1／204
OnlyR／Gmodeisavailableon103R,OnlyGmodeisavailableon102A.
Absolutepressure
−100〜100kPa
200kPa
300kPa
−10〜10kPa
20kPa
50kPa
−100〜100kPa
200kPa
500kPa
−100〜1000kPa
1500kPa
2000kPa
−100〜1000kPa
2000kPa
3000kPa
0〜100kPa（abs）
200kPa（abs）
300kPa（abs）
PG-35 PG-30
102R 103R 101R 102R 103R102A
TwooutputsNPN/PNP:Transistoropencollector
Switchrating:30VDC100mAmaximum
Residualvoltage:1.2Vmaximum（NPN）／2.2Vmaximum（PNP）at100mA.
Display
Operationdisplay
Operating
conditions
Thermalerror
Fittingparttypes
Materialsatpressurereceivingarea
NetWeight
Accessories
Negativepressuredisplay
Displayaccuracy
IPprotection
Operatingtemperature
Operatinghumidity
Insulationresistance
Dielectricstrength
Vibrationresistance
Shockresistance
EMC
Full3digitLEDdisplay（displaycycle:4timespersecond）
−LEDislit
±1％FS
SW1LED（green）andSW2LED（red）lightupwhenswitchoutputsareON
MeetsIP65（pressuregaugemainbody）ofIEC
−10〜50℃（storage−20〜70℃）
35〜85%RH
100MΩminimumatDC500Vbetweenbundledleadsandpressureport
OneminuteatAC500Vbetweenbundledleadsandpressureport（1mAmaximumleakage）
10〜500HZ1.5mmmaximum／98.1m
／
S2,
 threedirections,twohourseach
490m/s2,threedirections,threetimeseach
SUS316L
Approx.150g（incl.2mcable）
O-ring（G3／8：P18,G1／4：P15）
Singlecrystalsilicon
Approx.80g（incl.2mcable）
Plasticsealingscrew,M5fittingscrew
R1/4,G3/8,G1/4,
gasketfitting9/16-18UNF Aluminumdie-castRc1/8
±3％FS（0〜50℃）
EMI：EN5501Group1,ClassB／1998
EMS：EN61326-1／1997：Thepermissiblechangeofdisplaycounts,setvalueofswitchoutput
andzero／spanvoltageofanalogoutputduringthetestnotexceed±5％FS.
±
kPa
＋／− SW1 SW2
−LED（red） Full3digitLED
SW1LED（green）
SW2LED（red）
Displayunit
Upbutton
Downbutton
Modebutton
NPNOpenCollectorOutputModel PNPOpenCollectorOutputModel
（brown）
（gray）
（black）
Switchoutput1
（white）Switchoutput2
（blue）
Powersupply
D.C10.8〜30V
Sensor
Sensor
Display
LED
Sensor
Sensor
Display
LED Powersupply
D.C10.8〜30V
COM COM
Shield
Analog
output
（brown）
（black）
Switchoutput1
（white）
Switchoutput2
（gray）
（blue）
Analog
output
loadload
load load
Shield FGterminalFGterminal
Wirecolor
Brown
Blue
Black
White
Gray
Shield
Connection
Power⊕
Common
SWoutput1
SWoutput2
Analogoutput
Fitting

IntheOperationsMode,pressthe
and buttonssimultaneouslyto
entertheInitialSettingsMode.
Note:Values forthe102R,
forthe103Randthe102A,
and forothertypes,areset
priortodelivery.
TheLEDofanitemflasheswhen
selectedusingthe button.
Pressthe and buttons
simultaneouslytoenterthe
InitialSettingsMode.
Pressthe buttonfor
morethanonesecond
toreturntothe
OperationsMode.
Pressthe buttontomove
tothenextdigit.Thevalue
ofthedigitmaybesetwhen
theLEDbelowthedigitflashes.
Usethe and buttontoset
thevalueofeachdigit.
3
OperatingProcedures
InitialSettingsMode
■MultiplierfactorSetting
■AnalogOutputSetting
Setmagnification
（elevenselections）
Setanalogoutput

（threeselections）
Setswitchoutput

（eightcombinations）
Initial
Settings
Mode
Setting1
Setting2
Hysteresis
（0〜300digits）
DigitalFilter
（F-0〜F-3）
Pressthe and
buttons
simultaneously
Pressthe button
（morethanone
second）
Pressthe and
buttons
simultaneously
Pressthe button
（morethanone
second）
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
Pressthe buttontomove
＋／− SW1 SW2
Third
digit
Multiplierfactor Analogoutput Switchoutput
1：Rmode
2：Gmode
3：Vmode
1〜4：SeparateMode
5〜8：WindowComparatorMode
First
digit
Second
digit
Note:“1”issetpriortodelivery.
Pressthe  buttonuntil
the−LEDunderthe
thirddigitflashes.
Setthevalueofthethird
digitto“4”using
 and
 buttons.
Pressthe buttonformore
thanonesecondtoreturn
totheOperationsMode.
Anexampleofsetting“4”.
※Changeofmagnificationsettingiseffectiveonlyforpressurereading.Setvaluesforswitchingarenotscaledautomatically.
Themultiplierfactorsettingisdeterminedbythevalueofthethirddigit:thered−LEDshouldbeflashingduringthesetting.
Theanalogoutputsettingisdeterminedbythevalueoftheseconddigit:thegreenSW1LEDshouldbeflashingduringthesetting.
Valueselected
Valueselected
Pressurerange（−Pr〜＋Pr）
Muitiplierfactor 101R 102R 103R 102A
1
2
3
Ｒmode（Compoundpressureoutput）
Ｇmode（Positivepressureoutput）
Ｖmode（Negativepressureoutput）
Mode
−Pr 0 ＋Pr
（Vzero）
1V
1V
1V
5V
5V
5V
Sectionscontaininganobliquestrokearemultiplierfactorthatcannotbeselectedbecauseofresolvingpowerordisplaydigits.
（Valueswillnotbedisplayedautomatically.）
Pressthe buttonuntilthe
SW1LEDunderthesecond
digitflashes.
Setthevalueofthesecond
digitto“1”usingthe and
buttons.
AnexampleofsettingtheRmodeinthe102Rrange.
Notes:Vmodefor102RandRmodefor101Raresetpriortoshipment.R／Gmodefor103RandGmodefor102Acanonlybeselected.
Operations
Mode
kPa
＋／− SW1 SW2
Pressure
Settings
Mode
Intheoperationsmode,press
the and buttonssimultaneously
toentertheInitialSettingsMode.
Pressthe buttonformore
thanonesecondtoreturnto
theOperationsMode.
1
2
3
4
5
6
7
8
9
A
b
−9.99〜9.99
−99.9〜99.9
−75.0〜75.0
−999〜999
−99.9〜99.9
−1.45〜1.45
−2.95〜2.95
−99.9〜99.9
−999〜999
−750〜750
−999〜999
−14.5〜14.5
−29.5〜29.5
−100〜999
−1.02〜9.99
−1.00〜9.99
−14〜145
−0.10〜1.00
−29〜295
0.0〜99.9（abs）
0〜999（abs）
0〜750（abs）
0〜999（abs）
0.0〜14.5（abs）
0.0〜29.5（abs）
×1
×0.0102
×10.2
×7.501
×102
×0.01
×10
×0.145
×0.000145
×0.001
×0.2953
1：× 1
2：×0.0102
3：×10.2
4：×7.501
5：×102
6：×0.01
7：× 1 0
8：×0.145
9：×0.000145
A：×0.001
b：×0.2953
Whenthepowerisswichedon,theOperationsModeisautomaticallyselected.Settingsremainineffectafterswitchingoffthepower.

Pressthe and buttons. Setthevalueto“F-3”
usingthe and 
buttons.
Pressthe and buttons.
Pressthebuttonuntil
theSW1LEDflashes.
Setthevalueto“60.0”
usingthe and 
buttons.
Pressthe buttonformore
thanonesecondtoreturn
totheOperationsMode.
Pressthe buttonfor
morethanonesecond
toreturntotheOperations
Mode.
Setthevalueofthefirst
digitto“7”usingthe
and buttons.
Pressthe button
untiltheSW2LED
underthefirstdigit
flashes.
Intheoperationsmode,
pressthe and 
buttonssimultaneously
toentertheInitial
SettingsMode.
4
PressureSettingsMode
■SwitchOutputSetting
Theswitchoutputsettingisdeterminedbythevalueofthefirstdigit:theredSW2LEDshouldbeflashingduringthesetting.
Therearefouroperationmodes.Theseareshowninthediagramsbelow.
Note1.IntheSeparateMode,setting1correspondstoSW1,andSetting2correspondstoSW2.
Note2.IntheWindowComparatorMode,theminimumvalueforSW1andSW2correspondstoSetting1andthe
 maximumvaluecorrespondstoSetting2.
Valueselected
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
＋／− SW1 SW2
Pressthe and buttons
simultaneouslytoenter
thePressureSettingsMode.
（TheSW1LEDflashes.）
TheLEDofanitemflashes
whenselectedusingthebutton.
Pressthe buttontoselect
betweenswitchoutput1setting
（SW1）,switchoutput2setting
（SW2）,orthehysteresissetting.
Setthevalue
usingthe
andbuttons.
Pressthe buttonfor
morethanonesecond
toreturntotheOperations
Mode.
Output
Mode
Operation
1
2
3
4
5
6
7
8
SW1output
Separate
H
○
○
L
○
○
A
○
○
B
○
○
H
○
○
L
○
○
A
○
○
B
○
○
Windowcomparator
Note1
Setting1
Note2
Minimum :Setting1
Maximum:Setting2
Minimum :Setting1
Maximum:Setting2
Note1
Setting2
Note2
Separate
Windowcomparator
SW2output
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
Anexampleofsettingthevalue“7”forthemodeshowninthediagram.
■WindowComparatorMode
ON
ON
OFF
OFF
SW1
SW2
Setting
value1 Setting value2
Hysteresis Hysteresis
SeparateMode WindowComparatorMode
Hysteresissetting Switchoutput2
setting
Switchoutput1
setting
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
Low High
（Hoperation）
OFF
ON
ーPr Pr
HH
P1：SW1 P2：SW2
ON
OFF
ーPr Pr
HH
P1：SW1 P2：SW2
（Loperation）
（Aoperation）
OFF
ON ON
ーPr Pr
H H
P1 P2
P1 P2
（Boperation）
OFF OFF
ON
ーPr Pr
H H
F-0：ResponseTime=5ms
F-1：ResponseTime=25ms
F-2：ResponseTime=250ms
F-3：ResponseTime=2.5s
Digitalfiltersetting
＋／− SW1 SW2
P1≦P2 or P1≧P2 P1≦P2−2H
Note:+50%F.S.issetpriortodelivery.
Anexampleofsetting60kPaforswitchoutput1（SW1LEDisflashing）with102R.
Tosetswitchoutput1theSW1LEDshouldbeflashing.（Tosetswitchoutput2theSW2LEDshouldbeflashing.）
Note:20digitsissetpriortodelivery.
Anexampleofsettingahysteresisvalueof8.0kPawiththe102R（kPa）.
■SwitchOutputSetting
■HysteresisSetting
■DigitalFilterSetting
Tosethysteresisthe“−”LEDshouldbeflashing.
TosetDigitalFilterallLEDshouldbenotflashing.
Anexampleofsetting2.5sresponsetimebyDigitalFilter.
Pressthe buttonuntil
the−LEDflashes.
Setthevalueto“8.0”
usingthe and 
buttons.
Pressthe buttonfor
morethanonesecondto
returntotheOperations
Mode.
Note:“F-0”issetpriortodelivery.
Pressthe buttonuntil
allLEDdonotflashe.
Pressthe buttonfor
morethanonesecondto
returntotheOperations
Mode.
Pressthe and buttons

PressingtheandbuttonssimultaneouslyintheOperationsModedisplays onthescreen.Onesecondlaterthischangetothantheandbuttons
arereleased.（Ifthepressureportisopenedtotheatmosphere.）
5
Troubleshooting
ZeropointAdjustment
Others
Useawrench（13mm）onthealuminumdie-casting.Donotholdtheplasticcasewhentightening.Applysealingtapeatthemalescrewareatoprotectagainstair
leaks.Ifmountingwithanangledbracket,themaximumtorqueoftheM3screwsshouldbelessthan0.3N･m.
Whenusingtheaccessoriessealingorfittingscrew,bindupthesealtapearoundthesealingscrewoneandahalfortwoturns,andscrewitinthepressureportby
handwithoutdamagingthescrewthread.Afterthen,tightenthescrewsufficientlywithwrench.（Recommendedtorque:Plasticscrew3.0N-m,Metalscrew10.0N-m）
Ifthereisanypossibilitythatthesensormaybecomewetwithoilorwater, whichmay enterthe casethroughtheairintake,
connectasilicontube,orsimilar,totheintakeandpositiontheendofthetubeinasuitablysafeplace.Besurenottobendthe
tubeorblocktheendofthetube.
■Tubeatatmosphericpressureintake
■Piping
Exampleofatubewith
externaldiameterofφ4
andinternaldiameter
ofφ2.5
＜Non-Display［Temporary］Mode＞
・When the keys are not operated for more than 10 seconds during Operation Mode,the system will automatically select
Non-Display［Temporary］Modeandthedisplaywillturnoff.
・DecimalpointLEDshowninthefigurebelowwillblinkduringNon-Display［Temporary］Mode.
・UsingtheEEPROM,thePG-30/35seriescanretainpresetvaluesevenifthepoweristurnedoff.
・Ifanerrormessageisdetected,thedisplaywillcomebackandshowtheerrormessage.
・YoucanchangeanyfunctionsduringNon-Display［Temporary］Mode.
＜Non-Display［Full-time］Mode＞
・InNon-Display［Full-time］Mode,thedisplaywillbeturnedoffandtheKeyswillbelocked.
・DecimalpointLEDshowninthefigurebelowwilllightupduringNon-Display［Full-time］Mode.
・UsingtheEEPROM,PG-30/35seriescanretainthepresetvaluesevenifthepoweristurnedoff.
・Ifanerrormessageisdetected,thedisplaywillcomebackandshowtheerrormessage.
・YoucannotchangeanyfunctionsduringNon-Display［Full-time］Mode.
・ToenableNon-Display［Temporary］Mode,press keyformorethan4seconds. willbedisplayedandNon-Display［Temporary］Modewillbeset.
After10seconds,displaywillgooff.
・TodisableNon-Display［Temporary］Mode,press keyformorethan4seconds. willbedisplayedandNon-Display［Temporary］Modewillbecanceled.
（Howtoset）
■Non-DisplayMode
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
・ToenableNon-Display［Full-time］Mode,press keyformorethan4seconds. willbedisplayedandNon-Display［Full-time］Modewillbeset.Displaywill
turnoffinasecond.
・TodisableNon-Display［Full-time］Mode,press keyformorethan4seconds. willbedisplayedandNon-Display［Full-time］Modewillbecanceled.
（Howtoset）
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
Blink
Lightup
kPa
＋／− SW1 SW2
■Ifthefollowingerrormessagesaredisplayed,followtheproceduresinthetable.
Displayandproblem Cause Solution
E
- 1
E
- 2
E
- 3,E - 4
999Flashing
Flashingofthepressurevalue
Blackoutofthedisplay
Disablethekeyoperation
Outputcurrentisexceeding100mA. Turnoffthepowerandverifytheload
connectedswitchoutput1and2.
PressMbuttonandreturntheappliedpressuretothe
atmosphericpressureandtryzero-pointadjustmentagain.
Pleasecontactus.PleaseusearegulatedDCpower
supplyandmeasuresforthepowerlinenoise.
Normalstate
Normalstate
Normalstate(SeeNon-displaymode.)
Normalstate(SeeKeyprotectionmode.)
Pressurewasappliedatthezeropoint
adjustment.
Failureoftheinternalcircuit.
Pressurevaluesexceedthedisplayrange.
Pressurevaluesexceedtheratedpressure
range.（110%FS）
Non-displaymode
Keyprotectionmode
Note:YouhavetoadjustZerounderopenaircondition.
OtherwiseyoucanbeseenE‐2errorasyouadjustedZerowithresidualpressure.
102AmodeZeropointisadjustedpriortodelivery.(0.3kPaabsmax.)

6
OutlineDimensions
・ToenableKeyProtectionMode,press keyformorethan4seconds. willbedisplayedandthekeyswillbelocked.
・TodisableKeyProtectionMode,press keyformorethan4seconds. willbedisplayedandthekeyswillbeunlocked.
＜KeyProtectionMode＞
・KeyProtectionModeisusedtolockthefrontpanelkeyinordertopreventpresetvaluesfrombeingaccidentallychanged.
・UsingEEPROM,thePG-30/35seriescanretainthepresetvaluesevenifthepoweristurnedoff.
■KeyProtectionMode
（Howtoset）
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
kPa
＋／− SW1 SW2
Unlessotherwisespecifiedtolerance:±0.5（Unit:mm）
■PG-35OutlineDimensions
Fittingpart:R2type
Fittingpart:VCtype Fittingpart:GFtype Fittingpart:G2type
□31.4
□30
21
30
（66.2）
R1/4（PT1/4）
（WithM5femalescrew）
（68.7）
9/16-18UNF
（63.8）
G3/8（PF3/8）
（65.7）
G1/4（PF1/4）
（WithM5femalescrew）
■PG-35-BOutlineDimensions
■PG-30OutlineDimensions
Fittingpart:R2type
Fivecoreshieldedcable
L=2000±100
37
10.5
16
Airintake
16
（32）
2−M4
Depth5
□31.4 （65）
□30 36
21
10
19
（67.5）
9/16-18UNF
36
19
（64.5）
36
22
（62.6）
36
25
Fittingpart:VCtype Fittingpart:GFtype Fittingpart:G2type
R1/4（PT1/4）
（WithM5femalescrew）
Fivecoreshieldedcable
L:2000±100
G1/4（PF1/4）
（WithM5female screw）
G3/8（PF3/8）
Fivecoreshieldedcable
L=2000±100
2-M3
Depth3
Airintake
Pressureport
2-Rc1/8depth7
30
20
30 35.5
9
6.5
20

7
Brackets（Option）
ModelNumbers
■PG30bracketforwallattachment
（soldseparately）
■PG-35/PG-30Panelholderset・holdercover（soldseparately）
Panelholderset
30
396
20
φ4.2
2-φ3.5
φ4.2×5.2
Ellipticalhole
30
15
18
Afterinstallation 18
（□42.6）
Afterinstallation
25
15
Material:SUS
t=1.6
□40
（5.7）
4.5
Panelholdercover
Panelholder
Mainbody
（PG-30/PG-35）
Attachment
panel
Panelstopper
（two）
23.5
36＋0.5
0
36＋0.5
0
panelcutdimensions（Panelthickness:1〜3.6）
Holder
coverset
Panel
holderset
Pressureranges
101：−10to10kPa（PG-30only）
102：−100to100kPa（0〜100kPaforabsolutepressuretype）
103：−100to1000kPa
Fittingparttypes（PG-35only）
Ｒ２：R1/4（WithM5femalescrew）
ＧＦ：G3/8（Flashdiaphragmtype）
Ｇ２：G1/4（WithM5femalescrew）
ＶＣ：9/16-18UNF（Gasketfitting）
Modelnames
PG-30：Non-corrosivegastype
PG-35：Highcorrosionresistancetype
Switchoutputtype
Ｎ：NPNopencollector
Ｐ：PNPopencollector
Pressurereference
Ｒ：Compoundpressure（negativepressure〜positivepressure）
Ａ：Absolutepressure（absolutevacuum〜barometicpressure）【PG-35only】
20
40
2-φ3.5 20
20
15
φ4.2 20
30
φ4.2×5.2
Ellipticalhole
Material:SUS
t=1.6
PG−35−102R−NR2B
Port
Blank：Stemmount
B：Backmount
■Accessories（Soldseparately）
Productname Modelno. Description
Applicable
model
Bracketforwall
attachment
Bracketforflood
attachment
Panelholderset
Holdercoverset
（forprotectionof
gaugesides）
ACPG-001 PG-30
Bracketforwall
attachment,twoM3×4
malescrews
Bracketforfloor
attachment,twoM3×4
malescrews
Panelholdercover,
panelholder,two
panelstoppers
Panelholdercover,
panelholder
ACPG-002
ACPG-003
ACPG-004
PG-30
PG-30
PG-35
PG-30
PG-35
■PG-30bracketforfloorattachment
（soldseparately）
Warranty
Thisproductcanbecoveredbyone-yearwarranty.COPALELECTRONICSwarrantsthatanypartoftheproductwhichprovestobedefectiveduetothedesignand/or
manufacturingofCOPALELECTRONICS within one yearfromthedate of delivery willberepairedor replaced, freeofcharge.Note that the warrantywillonlybe
appliedtotheproductalone,nottodamagesinducedbyanyfailureofthaproduct.
Thewarrantywillnotbeappliedinanyofthefollowingcases:
①Failureanddamagecausedbyimproperusenotconformingtotheinstructionmanualornegligenthandling.
②Failureanddamagecausedbyinappropriatemodification,adjustmentorrepair.
③Failureanddamagecausedbynaturaldisaster,fireorotheractofGod.