Blueview ZNSR4-10M User manual

01
LED SILICONE NEON FLEX
ZNSR4-10M
1. Digital neon with 4040 RGB SMD
2. Adopt high quality components and special circuit design for reliable performance
3. Unique extrusion process and electronic design can be bended in horizontal way
4. Excellent flexibility for proper bending and easy modeling
5. To achieve rich light changes like chasing,running and water ripple effects with controller
6. Excellent weather (IP68)
7. resume from breakpoint available,does not affect the signal transmission when a group
of lights do not appear bright,
facade lighting, steps,booth,bridges,hotel,KTV decorative lighting,etc
by clips
4040 12V196° 3Years
IP68
Features
Application
Installation
TM1914
1800K
3000K
4000K
5500K
6500K
8000K
12000K
Y
O
R
G
B

02
LED SILICONE NEON FLEX
ZNSR4-10M
Model No. Light Color Color Temperature/
Wavelength(K/nm)
Luminous Flux
(lm/m)
Efcacy
(lm/W)
Voltage
(DC V)
ZNSR4-10M
RGB
R
G
B
196°
48
17
29
7
--
4.415
3.64
100000
620-625
520-525
465-470
5.25
1.15
12
Beam
Angle Ra Power
(W/m)
NOTE:
Test environment temperature : 25±2°C.
The above data is typical values. The actual data of each single product may differ from the typical values. The data is subject to change without notice.
Different color temperature will make luminous ux different.
The RGB data here is tested with three lights on and under control.
The RGB data here is tested in accordance with a certain state of the controller SP105E, so the power of RGB is not equal to the sum of three single light.
Luminous flux & power tolerance within ±10%.
Model No.
ZNSR4-10M60 5000*12*15 5 50
LED Quantity
(pcs/m)
Product Size
L*W*H(mm)
Max Run(Single
Feed)(m)
Min Cuttable
Length(mm)
Working
Temperature
Storage
Temperature
-20~+60 -20~+70
Specication
Other Parameters
Bending Diameter mm[inch]
Light Surface
10mm
12mm
25mm
Sectional view

03
LED SILICONE NEON FLEX
ZNSR4-10M
Working Length vs. Recommended Power Supply
Working Length
(m)
Model No.
1
5
1.08
5.4
12
20
80
12.96
64.8
Single Feed
Single Feed
Rated Current
(A) Rated Voltage (DC V) Rated Power (W) Power Supply Mode
Recommended Power
Supply(W)
ZNSR4-10M
Prole Drawings
Unit:mm
50[1.97]
16.0 [0.63]
815[32.09]
1.ZNSR4-10M
Single Feed
note:
Please ask the sales for detail drawing.

04
LED SILICONE NEON FLEX
ZNSR4-10M
Luminous Intensity Distribution Diagram
Note:The above two figures are tested with ZNSR4-10M in a certain state of the controller SP105E and
RGB three lights on. Please ask the sales for data of other Model or colors
Average Illumination
Light Intensity：cd
C0/180,246.2°
C90/270,112.9°
Average Beam Angle(50%)：179.6°
ZNSR4-10M
Flux Out：18.26lm (RGB)
2cm
4cm
6cm
8cm
10cm
12cm
14cm
16cm
18cm
20cm
680.9,1860lx
1532,4185lx
6128,16741lx
383.0,1046lx
245.1,669.6lx
170.2,465.0lx
125.1,341.6lx
95.76,261.6lx
75.66,206.7lx
61.28,167.4lx
5.95cm
11.89cm
17.84cm
23.79cm
29.73cm
35.68cm
41.62cm
47.57cm
53.52cm
59.46cm
Height Eavg，Emax Beam Angle：112.14°Diameter
ZNSR4-10M

05
LED SILICONE NEON FLEX
ZNSR4-10M
Product accessories
End cap with hole (FREE)
Quantity(10m):3pcs
Screw (FREE)
Quantity(10m):20pcs
End cap without hole (FREE)
Quantity(10m):3pcs
3.5cm installation aluminum
prole (OPTIONAL)
Quantity(10m):20pcs
Hardware mounting clips
(OPTIONAL)
Quantity(10m):20pcs
Silicone glue (OPTIONAL)
Quantity(10m):1pcs
Controller(OPTIONAL)
Quantity(10m):1pcs
Packaging Information
Label the reel; Put the packed static shielding
bag into carton box;
Seal the carton box; Label the box; Use packing belt to pack. Add
edge protectors if necessary.
Put reel, accessory bag and
desiccant together into static
shielding bag;
Seal and label the static
shielding bag;
Packaging information
Model No.
ZNSR4-10M5000*12*15 390*390*325 510 20.75(1±10%) 24.15(1±10%)
Product Size（mm) Carton Size（mm) Meter/Reel Reel/Carton Net Weight(kg) Gross Weight(kg)
More accessories can be provided according to customer requirements
Multiple controllers for option.
Note:
1. Each 1 piece for a reel and every 1 reels packed in a static shielding bag.
2. The above quantity and weight are only for the illustrated packaging method. There will be differences in the quantity and weight with
other packaging methods.

06
LED SILICONE NEON FLEX
ZNSR4-10M
1
2
2
4
Installation
1.Tools
Cutter LED power supply Electric batch Brush
2.Installation steps
Details of installation operation at input end
Details of installation operation at the end part
Weld the wire to the PCB
board.
First put some glue inside of
the plug, then push into the
tape light
Wipe off the excess glue and
wait for the glue to solidify.
First put waterproof glue
inside of the plug, then push
into the tape light.
Wipe off the excess glue and
wait for the glue to solidify.

07
LED SILICONE NEON FLEX
ZNSR4-10M
Screw the aluminum track to
the installation position.
Then slowly press the tape
light into the aluminum track.
GND for negative
pole of power supply
GND for negative
pole of power supply
Wire
Sequence
VCC for positive
pole of power supply
VCC for positive
pole of power supply
DAT for data line
CLK for clock signal
The tape light is atly and
rmly stuck on the aluminum
track.
3. Operation details of installation card
At welding part, note the positive and negative poles of lines and board and the
corresponding colors on the board; positive to positive and negative to negative
1.
1. The controller is SP105E.
2. SP105E supports controlling with bluetooth and mobile phone APP.
3. Bluetooth remote control distance is 20 m.
4. SP105E can drive up to 2048 pixels.
5. The input voltage of the controller ranges from DC 5V to DC 24V.
6. For additional information, please refer to the SP105E Instruction Manual.
The SP105E recommended load is less than 50m;
Each connection point must use 10g silica gel, and treat waterproof and
insulation well;
2.
The screw of installation card must perpendicular to installation surface and be
fastened, as shown in the right.
3.
Note:
Note:
Controller Wiring Diagram
Lighting surface.4.

08
LED SILICONE NEON FLEX
ZNSR4-10M
Attentions before installation
Cutting marks are on the PCB and can be seen though the product
The above diagram only shows the correct or wrong way of operation. The product should be based on the actual product.
Note:
Before installation, check that the product parameters are consistent with the requirements (Seeing product specicationsor
product labels)
Load voltage, current, power and power supply should be matched with the product.
Follow the instructions of wiring diagram (rst connect the load and then the power supply) to avoid short circuit.
Make sure the correct connection of positive and negative poles between led module and power supply. Otherwise, the light will
not be on.
Make sure the power cord rmly screwed into the terminal and it should not be pulled out by hands.
The terminal should have insulation,waterproof and anti-corrosive treatment.
Attentions
Cuttable mark Neat and smooth cut Slide a spindle into the roll
and then place the roll with
spindle on top of the box
provided.
Correct usage of products
Gently unroll the xture
without excessive force.
No cutting distort No embossing operation Do not twist
Do not repeatedly bending
This will damage the circuit
Do not wring Do not bend 90° No recessing operation

09
LED SILICONE NEON FLEX
ZNSR4-10M
Repair should be operated by a qualied technician, if the external circuit or main line of this product is damaged.
The parameters given in this manual are typical values and for reference only.
All illustrations and drawings in this manual are for reference.
This product is subject to change without notice.
LED lighting products belongs to electronic products, please do recycling treatment according to the relevant WEEE directives.
Statements:
Recycling:
Warning
Do not disassemble or retrot the light. Do not touch the surface of the
light with a sharp object.
Do not do live-line working during installation,especially for high voltage
product.
Do not use any organic chemical solvents.
Use neutral glass adhesive to x this product and it needs to be dried 4
hours in the open environment after operation.
Treat the ends and the circuit connection points that are not connected
to the main line with insulation,waterproof, and anti-corrosion in the
installation.
Use 18AWG (0.75mm2 cross-sectional area) or thicker core wire to
avoid adverse consequences caused by overheating, if the power cable
need to lengthen.
Make sure the input voltage meets the requirements and lines are
connected correctly before lighting on.
This product is for signage, and do not use as general lighting.
Series connection within the max run.
The length of the power cable between the power supply and the led
strip should not exceed 2 meters.Otherwise, large circuit loss will lead
to inconsistent brightness.
Installation, maintenance and repair should be operated by a qualied
technician.
Quick Guide
Problems
All LEDs can
not light on.
LEDs can not
light on partly.
Brightness of
LED
is inconsistent
tor insufcient.
LED icker.
Automatic power protection
from the open or short
circuit in output of the power
supply. Fix the short circuit problem.
Correctly connection
Check the power supply
system to x it.
Replace with more powerful
power
Make sure the working voltage of
the product within ±5% of standard
voltage, or keep balance by circuit
power consumption.
Reduce the quantities of the product in
series connection to meet requirement.
Fix the short circuit problem.
Wrong connection of power
supply.
Some switching mode power
supplies are not powered.
Power supply line error.
Mistaken wire connection of
some of products
Power overloaded.
Connection point fault. Remove bad connection point.
Replace a new power supply.
Please follow the instructions
Power supply circuit
excessive consumption.
Excessive quantities in series
connection of the product
Switching power supply
failure.
Wrong Installation or use of
products
Reasons
No electric supply.
Solutions
Common Faults and Troubleshoot
Statements and Recycling
Do not connect the chain to the supply while it is in the packing.
The LEDs are not replaceable.
This lighting chain must not be used without all gaskets being in place.