BN Thermic ETH Series User manual

BNTMETH02
Thank you for purchasing a BN Thermic product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
1.1 ELECTRICALSAFETY
 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. If in any
doubt consult a qualified electrician. You must also read and understand the following instructions concerning electrical safety.
1.1.1 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances and
the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.2 Ensure that the insulation of all the cables on the appliance is safe before connecting it to the power supply.
1.1.3 Ensure that the cables are always protected against short circuit and overload.
1.1.4 Regularly inspect the power supply cables and plugs etc. for wear or damage and check all connections to ensure that none are loose.
1.1.5 Important: Ensure that the voltage marked on the appliance matches the power supply to be used and that a correctly rated fuse is fitted.
1.1.6 Installation should always be carried out by a qualified electrician in accordance with current electrical regulation, protected by a suitably
rated isolator and fuse or mcb.
1.1.7 DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a qualified
electrician.
1.2 GENERAL SAFETY INSTRUCTIONS
Remove all packaging and store it away from children, check the package and heater for visible damage or tampering.
Familiarise yourself with the applications and limitations of the heater.
Ensure the heater is in good order and condition both physically and electrically before use. If in any doubt do not use the unit
and contact your supplier.
Only use recommended attachments and parts. To use unauthorised parts may be dangerous and will invalidate your warranty.
Disconnect from mains and allow to cool before attempting any cleaning.
X DO NOT use in hazardous areas.
X DO NOT touch the heating segments at any time as the radiant surfaces will become dirty (if necessary when installing then use clean
textile gloves).
X DO NOT use if ambient temperatures exceed 30°C.
X DO NOT cover the heater or restrict free circulation of air around it.
X DO NOT locate the heater below the power outlet.
X DO NOT install this heater against combustible low-density fibre board surfaces.
X DO NOT disassemble the heater for any reason. This heater must be checked by qualified personnel only.
X DO NOT use this heater to perform a task for which it has not been designed.
 WARNING! This heater is not equipped with a device to control the room temperature. Do not use this heater in a small room if it is
occupied by people not capable of leaving the room on their own, unless constant supervision is provided.
 WARNING! Ensure there is no possibility of inflammable materials coming into contact with the heater.
2. INTRODUCTION & SPECIFICATION
ETHSeries terrace heaters are designed for the zonal heating of conservatories, enclosed and roofed balconies and terraces, gazebos, marques etc.
–i.e., applications where they are protected against direct contact with the effects of the weather. They have a significantly lower surface
temperature than halogen heaters, and they do not radiate unwanted light when in operation.
Model
ETH-10
ETH-15
Power
1000W
1500W
Input supply
230V 50Hz 4.4A
230V 50Hz 6.5A
Dimensions (W x H x D)
1080 x 140 x 45mm
1580 x 140 x 45mm
Weight
4.0Kg
6.0Kg
Protection
IP44
IP44
INSTRUCTIONS FOR:-
TERRACE HEATERS
ETH Series
IMPORTANT: PLEASE READ THESE INSTRUCTIONS, NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS,
AND CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
REGISTER: PLEASE REGISTER THIS PRODUCT ONLINE TO ACTIVATE YOUR GUARANTEE AT
www.bnthermic.co.uk

This product conforms to EU Directive 2002/96/EC.
This appliance bears the symbol of the crossed waste bin. This indicates that, at the end of its useful life, it must not be disposed of as
domestic waste, but must be taken to a collection centre for waste electrical and electronic equipment. It is the user's responsibility to
dispose of this appliance through the appropriate channels. Failure to do so may incur penalties established by laws governing
waste disposal.
BN Thermic Ltd,
34 Stephenson Way, Three Bridges,
Crawley, RH10 1TN
Tel: [phone]
Email: [e-mail]
Web: www.bnthermic.co.uk
3. MOUNTING / INSTALLATION
 IMPORTANT! Ensure that the mounting surface is capable of supporting the weight of the
heater.
X DO NOT place heater directly below any electrical socket / connection.
X DO NOT allow any flammable objects to come within 100cm of the radiant surface.
X DO NOT allow any flammable objects to come within 30cm of any other part of the heater
case.
 IMPORTANT! Observe minimum mounting distances.
3.1 CEILING MOUNTING
Panels can be hung from the ceiling using chains or cords which must be attached to the
round bracket on the back of the panel. Supplied wall brackets are not required with this
mounting, observe mounting clearances.
3.2 WALL MOUNTING
The radiant panel can be wall mounted using the supplied brackets and tilted at various
angles that the bracket allows, observe mounting clearances.
3.3 PARASOL MOUNTING
The panel can be mounted on suitable parasol arms having a maximum angle of 45º
ensuring the correct mounting clearances are maintained.
3.4 MOUNTING DIMENSIONS (Dims in brackets are for ETH-15 model )
3.5 ELECTRICAL CONNECTION
 IMPORTANT! Ensure you have read the Safety instructions and you are a suitably
qualified electrician before continuing.
 IMPORTANT! The voltage marked on the heater must correspond to the supply
voltage.
 IMPORTANT! To comply with the I.E.E. Wiring Regulations, the appliance must be
earthed; the supply circuit must be adequate for the input of the appliance, and the
circuit protected by a suitable fuse. If the heater is to be connected to a fixed electricity
supply, a suitable termination must be provided adjacent to the final position of the
appliance. In this instance, such a termination must be a double pole switch with a
contact separation of at least 3mm in all poles.
3.5.1 Connect the Earth wire GREEN / YELLOW to the earth terminal E or having the symbol -
Connect the Live wire BROWN to the live terminal ‘L’.
Connect the Neutral wire BLUE to the neutral terminal ‘N’.
4. OPERATION
When energised the heater will provide its maximum output in around 5 Minutes. During the first heating of the panel, burning out
of the material takes place, which can cause a harmless smell and (smoke) for a maximum period of 60 minutes. This is perfectly
normal and only occurs for the first hour of use.
5. MAINTENANCE
BN Thermic Electric Heaters are factory assembled, tested and are non-user serviceable. They are designed to operate for many years, problem
free. Maintenance is limited to dusting and wiping with a damp cloth and detergent. DO NOT clean the radiant surface. Note: - Before carrying out
any cleaning ensure the heater has cooled down and is disconnected from the mains supply.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Your BN Thermic product is guaranteed for one year from date of purchase. We
will repair or replace at our discretion any part found to be defective. We cannot assume any
consequential liability. This guarantee in no way prejudices your rights under common law and is
offered as an addition to consumer liability rights.
REGISTER: Activate your warranty by registering online at www.bnthermic.co.uk and retain this
installation data for future reference. ETHINS-v02
mm
mm