Bodet Profil TGV 950 User manual

1
Clock
Prol TGV 950
Prol TGV 970
AFNOR / IRIG B receiver
RADIO receiver
INSTALLATION AND OPERATING INSTRUCTIONS
1 rue du Général de Gaulle
49340 TRÉMENTINES
FRANCE
Tél. : [phone]
www.bodet-time.com
Upon receipt, always check the product for damage during shipment. If any is found, you may le a damage
claim with the carrier
Réf.: 607100 F

2
Table of contents
I - INITIAL VERIFICATION 3
1.1 Unpacking the clock 3
1.2 Cleaning 3
II - DISCLAIMER 4
III - INSTALLATION 4
3.1 Mechanical installation 4
3.2 Setting in operation 5
3.2.1. AFNOR/IRIG-B receiver clock 5
3.2.3. Radio receiver clock 6
3.3 Setting the antenna 7
IV - SAFETY INSTRUCTIONS 8
IV - TECHNICAL FEATURES 9
TGV 950 9
TGV 970 10
V - WHAT TO DO IF...? ...CHECK. 11

3

4
I - INITIAL VERIFICATION
Thank you for choosing a BODET clock. This product has been carefully designed for your
satisfaction based on ISO9001 quality requirements. We advise you to read this manual
thoroughly before attempting to manipulate the clock.
Keep this booklet during all the life of your clock, so that you can refer to it each time it is
necessary.
Bodet accepts no responsibility for accidents resulting from any use not conforming with the
above provisions.
Any modication to the product will invalidate the warrantee.
1.1 Unpacking the clock
Unpack with caution and check the contents of the packaging. It must contain :
- the TGV clock,
- for radio synchronised models : the antenna,
- a key to open the casing,
- an antistatic cleaning kit,
- this booklet.
Versions : a label inside the clock species what model the clock is :
AFNOR HMS or AF HMS = the clock is a receiver driven by : a master clock that sends
AFNOR NFS-87500A coded time messages or a radio receiver antenna, and powered by
240 VAC, with a servo second hand.
1.2 Cleaning
Use an antistatic product of similar type to the one shipped in the original packaging. Never use
alcohol, acetone or any other solvent liable to damage the casing and glass on your clock.

5
II - DISCLAIMER
Bodet accepts no responsibility for accidents resulting from any use not conforming with the
above provisions.
Any modication to the product will invalidate the warrantee.
Read the chapter «Safety instructions» in this manual before installing this equipment.
III - INSTALLATION
3.1 Mechanical installation
Select the place where the clock will be installed while making sure that radio reception is
correct for radio synchronisation models.
TGV 950 clock
TGV 970 clock
230
322
162
162
Ø 500
Ø 500
Ø 140
Ø 230
Ø 270
24 trous Ø 8,20
322
163
360
180
163
Ø 700
Ø 700
360
180
360
Ø 470
24 trous Ø 11
sur un Ø430

6
■Open the clock by giving the screw a quarter turn
with the key (5).
■On the TGV950 clock, remove the 2 locking
srews (3) (provided for the transit).
■Pull the whole dial (1) towards you.
■The hinge arm opening system ensures a fast
and secure maintenance of the lighting without
having to put the front part of the clock on the
ground.
■ Hang the clock and x it with screws, without
locking it, after you have put the wires through
the waterproof pressure joints (4).
3.2 Setting in operation
3.2.1. AFNOR/IRIG-B receiver clock
■ Switch o󰀨 the circuit breaker involved.
■Connect the mains 230 V +/-10% 50 Hz to the
terminal (6) (Live, Neutral and Earth wires; section
1.5 mm² to 2.5 mm² and bare on 5 mm). The mains
cable must be oversheathed up to the terminal.
■Attach the 3 wires (Live, Neutral an Earth) with the
cable tie.
■A double/reinforced electrical insulation must be
assured between the mains cable and the SELV
wires.
■Connect the time signal network to the terminals 1
and 2 of the AFNOR receiver card.
■Check that the dip switch (16) is pushed to the
AFNOR position.
■Check that the battery is connected to the terminal (2) of the electronic card.
■Lock the clock.
■Push the dip switch (15) to the ON position.
■Close the clock.
■Power the clock.
Operating principle of AFNOR receiver clock :
■When switching on power supply, hands are set at
12.00 until the correct reception of the time signal
is achieved. After 3 successive coherent AFNOR
time signals are received, the clock starts and
automatically get on time with fast impulses.
5
6
4
3
3
1
5
6
4
3
3
1
15
16
AF
FI
AFNOR
input

7
■During 1 hour without reception of the time signal the clock operates with its own time basis. If
the signal recovery is achieved within this hour, the clock will be resynchronised automatically.
After 1 hour the clock is reset and hands are set on position 12.00.
■Without power supply 230V the clock operates with its battery during 1 hour. After 1 hour
without time signal reception or if the battery voltage drops down, hands are set position 12.00
until power supply recovery.
■The synchronous second hand witch is powered by the main 12V 50Hz, will stop immediately.
3.2.3. Radio receiver clock
■ Switch o󰀨 the circuit breaker involved.
■Connect the mains 230 V +/-10% 50 Hz to the
terminal (6) (Live, Neutral and Earth wires; section
1.5 mm² to 2.5 mm² and bare on 5 mm). The mains
cable must be oversheathed up to the terminal.
■Attach the 3 wires (Live, Neutral an Earth) with the
cable tie.
■A double/reinforced electrical insulation must be
assured between the mains cable and the SELV
wires.
■Connect the two wires of the antenna to the
terminals 4 and 5 of the electronic card.
■Check that the dip switch (16) is in receiver position.
■Check that the battery is connected to the terminal (2) of the electronic card.
■Lock the clock.
■Push the dip switch (15) to the ON position.
■Close the clock.
■Power the clock.
Operating principle of radio receiver clock
■When switching on power supply, hands are set
at 12.00 until the correct reception of the time
signal is achieved. After 3 successive coherent time signals are received, the clock starts and
automatically get on time with fast impulses.
■Once the clock is synchronised, it operates with its own time basis. If the signal is back within
this period, the clock set itself automatically.
■Without power supply 230V the clock operates with its battery during 1 hour. After 1 hour
without time signal reception or if the battery voltage drops down, hands are set position 12.00
until power supply recovery.
■The synchronous second hand witch is powered by the main 12V 50Hz, will stop immediately.
5
6
4
3
3
1
15
16
AF
FI
Input 162

8
3.3 Setting the antenna
For radio synchronised clocks :
The best reception conditions are outside
buildings or near windows.
Positioning the antenna (perpendicular to the
direction of the transmitter) improves
reception.
The antenna must not be placed on a metal
support.
As for any radio system, a building with metal
structures can cause interference in the
reception of the signal.
Computers, television sets and electrical
appliances can also cause interference that
disrupt the reception of the radio message.
- Unlock the antenna from its support.
- Fix the support with the screw supplied and lock the antenna again.
Beware : in a double face system. So as not to cause interference
between the 2 antennas, the latter must be xed at least one metre
away from each other.
ALS

9
IV - SAFETY INSTRUCTIONS
Installation and maintenance of this equipment must be carried out by qualied personnel only.
Electrical installation must comply with current standard CEI 364. (NF C15-100 in France for
example).
This is a class I product.
Do not apply the power before installation.
The mains supply for the clock must include a circuit breaker rapidly accessible. It must break
neutral and phase simultaneously.
This circuit breaker must be switched o󰀨 during maintenance operations.
Use cable ties to attach the mains cable (see section “Installation).
Caution: use of an unqualied battery may present a risk of explosion. Waste battery should be
disposed so that they can be recycled.
LED lights can be hazardous to the eyes.
The LED lighting systems are less energy consuming than other types of lighting and have
lifetimes much longer.
Partly because of the limited nature of the surface emission, LEDs have luminances at least
1000 times higher than those of a traditional lighting source. The level of direct radiation from
such sources exceeds the level of visual discomfort.
Our clocks are designed so that there is no direct light, and thus no risk. However, it is
recommended to switch o󰀨 the lighting system before opening the clock for maintenance.

10
IV - TECHNICAL FEATURES
Power supply : 230 Volt 50 Hz ±10%,
Operating temperatures : -25°C to +50°C,
Protection index : IP54.
TGV 950
Readability : 40m.
Weight : 8 kg.
Lighting consumption : 14 W.
Dimensions :
TGV 970
Readability : 50m.
Weight : 16 kg
Lighting consumption : 20 W.
Dimensions :
322
162
Ø 500
Ø 140
Ø 230
Ø 270
24 trous Ø 8,20
Double face
clock
Single face
clock
Disk for hanging bracket or
suspension on a chain
322
163
360
180
Ø 700
180
360
Ø 470
24 trous Ø 11
sur un Ø430
Double face
clock
Single face
clock
Disk for hanging bracket or
suspension on a chain

11
Radio receiver clock with synchronous second hand HMS :
Permanent power supply: 230V 50Hz; 110mA pour une TGV950 et 140mA pour une
TGV970.
Earthing system: TT or TN (this product is also suitable for IT earthing system).
Battery: risk of explosion if the battery is not properly connected. Replace it with the same
model or with an equivalent model recommended in this manual. Follow the instructions in
this manual for changing the battery. This clock requires battery replacement by qualied
service personnel. The battery must be model VARTA Ni-MH 5/CP300H 6V-280mAh.
Accuracy : absolute with automatic summer/winter changeover.
AFNOR/IRIG-B receiver clock with synchronous second hand :
Permanent power supply: 230V 50Hz; 110mA for TGV950 and 140mA for TGV970.
Earthing system: TT or TN (this product is also suitable for IT earthing system).
Battery: risk of explosion if the battery is not properly connected. Replace it with the same
model or with an equivalent model recommended in this manual. Follow the instructions in
this manual for changing the battery. This clock requires battery replacement by qualied
service personnel. The battery must be model VARTA Ni-MH 5/CP300H 6V-280mAh.
Accuracy of the master clock.

12
V - WHAT TO DO IF...? ...CHECK.
What to do if...? … Check.
■No synchronisation after
the installation.
■Check that the type of signal send by
the master clock (min, ½ min, AFNOR/
Irig-B) is in accordance with the type
programmed in the clock.
■AFNOR / Irig-B receiver
stopped at 12h00.
■Lack of impulse since more than 1 hour,
check the master clock and the network.
■The synchronous second
hand is stopped on a
receiver clock.
■The permanent supply powering second
hand is cut-o󰀨. Check this power supply.