Body Craft 50442 User manual

ASSEMBLY INSTRUCTION
THE JONES STRENGTH TRAINING SYSTEM
Jones Cable Functional Trainer Attachment (for Light Commercial Model)
50442
Bodycraft is a division of Recreation Supply Inc.
P.O. BOX 181
Sunbury, OH 43074
QUESTION?
As a quality home gym supplier we are committed to your complete satisfaction. If you have
questions, or find missing or damaged parts, we will guarantee your complete satisfaction through
our authorized dealer service centers or our home office customer service department. Please call
your local dealer for assistance or BodyCraft at 800-990-5556 (9:00 AM - 5:00 PM). Our trained
technicians will provide immediate assistance to you, free of charge.

1
BEFORE YOU BEGIN
Congratulations and thank you for selecting the JONES MACHINE strength
training system. The JONES MACHINE offers an impressive array of
strength training exercises to develop every major muscle group of the body.
Whether your goal is cardiovascular fitness, a shapely, toned body or dramatic
muscle size and strength, the JONES MACHINE will help you achieve the
specific results you want.
For your safety and benefit, read this manual and the accompanying literature
before using the JONES MACHINE. Keep this manual for future reference.
If you have additional questions, please call your local dealer or our customer
service department at 800-990-5556 Monday through Friday, 9 a.m. until 5 p.m.
Eastern Time.
IMPORTANT SAFETY NOTES
1.This product must be assembled on a flat, level surface to assure its
proper function.
2.Clean pads and frame on a regular basis. We recommend warm,
soapy water. Do not use harsh or abrasive chemicals.
3.Inspect and tighten all parts before every use. Replace any worn
parts immediately. Failure to do so may result in serious injury.
4.Keep children away from the JONES MACHINE at all times.
5.Keep your hands away from cables and pulleys during operation.
Keep your hands away from moving parts other than the designated
handles.
6.When adjusting the seat, make sure the spring pin is fully engaged.
If not, the seat may slip and cause serious injury.
7.Make certain all cables are seated within the pulleys before every use.
8.Exercise with care to avoid injury.
9.If unsure about the proper use of the JONES MACHINE strength
training system call your local dealer or our customer
service department at 800-990-5556.
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your
physician. This is especially important for individuals over the age of 35
or persons with pre-existing health problems. Recreation Supply, Inc.
assumes no responsibility for personal injury or property damage
sustained by or through use of this product.

441
419
432 438
432
438
439439 436
438
404L447403R 447
419
437
419
419
419
55
51
51
51
42
438
441
441
441
438
443
443
444
436
439
439
436
439
436 436
439
438
419
437
419
419
417
446
446
417
410
410
418 418
409
409
414414
415
415
445
445
427
427
427
427
420
446
446
420
408L
407R
419
419
416
419
442
442
421
416
419
442
421
412
412
442
425
425
440
426
422422
402L401R
431
425
425
440
426
431
411
411
432
406L1
405R2
405R1
406L2
441
441
438
432 438
438
434
434 441
441
435
413413
435
436
439
424
424
432 438
432
430
430 441
430
438
441
438
432
423
423
441
441 419419
438
438
433
441
432
433
438
438
441
434
434
429429
428 428
441
438
441
438
438
438
430
438 432
432
OVERVIEW
2
438
430
438
55
51
51
42
51
438 432

401R
402L
403R
404L
405R1
405R2
406L1
406L2
407R
408L
409
410
411
412
413
414
415
416
417
418
419
420
422
421
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
RIGHT BASE FRAME
LEFT BASE FRAME
RIGHT TOP FRAME
LEFT TOP FRAME
RIGHT FRONT TOP PANEL
RIGHT REAR TOP PANEL
LEFT FRONT TOP PANEL
LEFT REAR TOP PANEL
RIGHT CABLE HEIGHT ADJUSTER
LEFT CABLE HEIGHT ADJUSTER
PULLEY BRACKET
SELECTOR ROD
SWIVEL PULLEY HOUSING
FRONT STACK SHROUD
REAR STACK SHROUD (colse to Jones)
GUIDE ROD
UPRIGHT FRAME
TOP CABLE
TOP PLATE
10 POUND PLATE
PULLEY
HAND GRIP (pre-assembled)
50mm CAP
CHAIN LINKS
POP PIN (pre-assembled)
SELECTOR PIN
BEARING
END CAP
PLASTIC BUSHING
RUBBER DONUT
PLASTIC GUIDE ROD HOLDER
BUSHING
STEEL SPACER
3/8" X 3" HEX BOLT
3/8" X 2-3/4" HEX BOLT
3/8" X 1-3/4" HEX BOLT
TOP PLATE BOLT
5/16" X 1/2" HEX THREADED BOLT
5/16" X 1/4" SET SCREW
(pre-prassembled)
3/8" WASHER
5/16" WASHER
24mm NYLON NUT (pre-assembled)
3/8" NYLON NUT
SNAP HOOK
SINGLE HANDLE
ANKLE STRAP
PULLEY HOUSING COVER
TRIM FOR SHROUD
3/8" X 4-1/4" HEX BOLT
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
4
2
2
2
38
16
2
2
2
2
2
4
2
4
4
4
8
2
18
4
4
2
8
4
44
8
2
26
4
2
1
2
8
4
401R
405R1
407R 408L 409 410
412
413
414
405R2 406L1 406L2
402L 403R 404L
411
417
418 419 420 421 422 423
428 429 430
431 432 433
424 425 426 427
415
434 435 436 437
438 439 440 441 442 443 444 445
446
447
416
PARTS LIST
NO. DESCRIPTION QTY.
01/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/4 1/4 1/2 3/41" 2" 3" 4" 1/4 1/2 3/4 1/4 1/2 3/45" 6"
(inch)
3

STEP 1 Base Frame Assembly
4
401L
422
401R
422
42 42
51 51
4
1. To ease assembly, DO NOT tighten any bolts until instructed. Wherever we
describe assembly for a right side component, please duplicate procedure for
the left side.
2. Remove two 3/8" X 4" Hex Bolts (42) on your Jones and attach Right Base
Frame (401R) to The Jones. Reuse the hardware two 3/8" X 4" Hex Bolts (42)
and two 3/8" Washers (51) only. Please make sure that you thread whole 3/8"
X 4" Hex Bolt (42) to the end. Attach 50mm Cap (422) to Right Base Frame
(401R).

STEP 2 Weight Base Assembly
5
407R
423
408L
433 433
438 438
429
428 428
414
414
435
435
417
417
410
410
418
418
424
424
415
415
429
401R 402L
438
438
441
441
1. Attach Upright Frame (415) to the Right Base Frame (401R), using two 3/8"
X 2-3/4" Hex Bolts (433), four 3/8" Washers (438) and two 3/8" Nylon Nuts
(441).
2. Insert two Guide Rod Holders (429) to the Right Base Frame (401R) as
shown.
3. Insert the two Guide Rods (414) into the Guide Rod Holders (429) in the
Right Base Frame (401R) and slide two Rubber Donuts (428) over top and
down the Guide Rods (414).
4. Slide the 10 lbs plate (418) {19 per side} over top and down the Guide Rod
(414). Make certain that each plate is oriented with selector hole on bottom
and facing forward. Attach the Top Plate (435) to the Selector Rod (410)
using the Top Plate Bolt (435). Tighten Top Plate Bolt (435) with Hex
Wrench (not provided). Screw the Pulley Bracket (409) into the Selector
Rod (410), only about half way. This will be an adjustment point in the
future. Slide Top Plate (417) over and down to the Guide Rods (414).
5. Slide the Right Cable Height Adjuster (407R) over the top of the Upright
Frame (415). Stop at your desired height by locking the Pop Pin (423).
423

STEP 3 Top Frame Assembly
6
403R 404L
415
414
415
414
2 2
437
437 447
447
51
51
447
51
55 55
447 6
51
1. Loosen the pre-assembled two 5/16" X 1/4" Set Screws (437) in the ringlets on
the Top Frame (403R) to allow it to easily slide onto the Guide Rods (414). Slide
the Top Frame (403R) onto the Guide Rods (414). Attach Right Top Frame
(403R) to Front Top Frame (2) of the Jones, re-using the two 3/8" X 4-1/4" Hex
Bolts (447), two 3/8" Washers (51) and two 3/8" Nylon Nuts (55) originally used
on the base Jones. Repeat for left side.
Tighten all Bolts.

STEP 4 Top Panel Assembly
7
441
441
438
438
441
441
438 432 432 438
438
406L1
406L2
405R2
405R1
403R 404L
438
438
438
438
438
432
1. Attach Right Top Panel (405R1 & 405R2), to the Right Top Frame (403R) as
shown using five 3/8" X 3" Hex Bolts (432), ten 3/8" Washers (438) and five
3/8" Nylon Nuts (441). Repeat for left side.
Tighten all Bolts.
438
438

R1
R4
R2
R5
STEP 5 Top Cable Assembly
TOP CABLE (416)
R1
419
416
419
411
430
430
430
441
438
438
438
432
R6 R3
R2,R3
441
419
R2
432
438
419
438
441
438
432
405R1 405R2
438
R3
R8
R7
R5,R6
438
438
419
441
438
438
405R1
405R2
432
R6
R5
8
R8
407R
R7
441
401R
419
434
R4
419
417
409
434 441
Assemble cables and pulleys simultaneously.
※Pulleys are mounted using 3/8" X 3" Hex Bolts (432), 3/8" Washers (438), and 3/8" Nylon Nuts
(441). Pay attention, as some places use washers, others don't.
1. Insert the threaded end of the Top Cable (416) between the pulleys in the front of the Right Cable
Height Adjuster (407R) as shown Fig. R1. Route the cable up and over two top Pulleys at the
Front and Rear of the Top Panel (405) as shown Fig. R2 & R3, then down to the Pulley Bracket
(409) as shown Fig. R4.
2. Continue routing over the two lower pulleys on the Top Panel (Fig R5 & R6) and then down to the
pulley in the welded bracket on the Right Base Frame (401R) as shown in Fig R7. Screw the
threaded end of the Top Cable (416) into the Bracket welded on the Right Cable Height Adjuster
(407R) AT LEAST one third of the way. This is a cable adjustment area. When all cables have
been tightened, make sure to secure the Jam Nut to prevent the Top Cable (416) from
unscrewing.

L1
L2
L3
L5
L6
STEP 6 Top Cable Assembly
TOP CABLE (416)
L1
419
416
419
411
430
430
441
438
438
432
L2,L3 441
419
L2
432
438
419
438
441
438
432 406L1
406L2
438
L3
L4
L8
L7
L5,L6
438
438
419 441
438
438
406L1
406L2
432 L6
L5
9
L7
441
419
434
401L
408L
L8
L4
419
417
409
434
441
Assemble cables and pulleys simultaneously.
※Pulleys are mounted using 3/8" X 3" Hex Bolts (432), 3/8" Washers (438), and 3/8" Nylon Nuts
(441). Pay attention, as some places use washers, others don't.
1. Insert the threaded end of the Top Cable (416) between the pulleys in the front of the Left Cable
Height Adjuster (408L) as shown Fig. L1. Route the cable up and over two top Pulleys at the
Front and Rear of the Top Panel (406) as shown Fig. L2 & L3, then down to the Pulley Bracket
(409) as shown Fig. L4.
2. Continue routing over the two lower pulleys on the Top Panel (Fig L5 & L6) and then down to the
pulley in the welded bracket on the Left Base Frame (402L) as shown in Fig L7. Screw the
threaded end of the Top Cable (416) into the Bracket welded on the Left Cable Height Adjuster
(408L) AT LEAST one third of the way. This is a cable adjustment area. When all cables have
been tightened, make sure to secure the Jam Nut to prevent the Top Cable (416) from
unscrewing.

STEP 7 Stack Shroud Assembly
10
436
439
436
439 403R
401R 402L
404L
446
436
439
436
439
413
(colse to Jones)
413
(colse to Jones)
446
446446
412
436
439
436
439
412
436
439
436
439
1. Attach Front & Rear Stack Shroud (412 & 413)
and Trim for Shroud (446) to the Right Top
Frame (403R) and Right Base Frame (401R)
using four 5/16" X 1/2" Hex Threaded Bolts
(436) and eight 5/16" Washers (439).
2. Change to "Repeat for left side.
Tighten all Bolts.

Thank you for purchasing the Jones Machine System. If You have
any questions, please call your local BodyCraft dealer or call our
customer service department at 800-990-5556
11
Assembly is complete! Please take the following steps
before using the
Jones Cable Functional Trainer Attachment :
1.Make certain all bolts are tightened securely.
2.For better performance, apply a household lubricant (such as silicone) to
VERTICAL GUIDE RODS(414).
3.Always be certain that RIGHT & LEFT CABLE HEIGHT
ADJUSTER(407R) are fully engaged when using
Jones Cable Functional
Trainer Attachment
.
4.Enjoy many years of a Fit Lifestyle.