Body Craft F602V2 User manual

Serial Number Location
Record your Serial number
and purchase date here:
S/N __________________
PURCH.DATE:_________
DEALER:______________
______________________
______________________
F602V2 FLAT / INCLINE / DECLINE
UTILITY BENCH
OWNERS MANUAL
SERIAL
12345678
Model No. F602V2 Recreation Supply, Inc.
BODYCRAFT
a division of Recreation Supply Inc.
7699 Green Meadows Dr.
Lewis Center, OH 43035

1
.
Congratulations and Thank You!
Important Safety Notes
QUESTIONS?
Thank you for selecting the Bodycraft F602V2 Flat Incline Decline Bench (FID).
The Bodycraft F602V2 offers an impressive array of strength training
exercises to develop every major muscle group of the body. Whether your
goal is cardiovascular fitness, a shapely, toned body or dramatic muscle size
and strength, the Bodycraft F602V2 will help you achieve the results you want.
For your safety and benefit, read this manual and the accompanying literature
before using the Bodycraft F602V2. Keep this manual for future reference.
If you have additional questions, please call your local Bodycraft F602V2
Dealer or our customer service department at 800-990-5556 Monday through
Friday, 9 am until 5 pm Eastern Standard Time.
There is a risk assumed by individuals who use this type of equipment.
Before beginning this or any other exercise program consult your physician.
This is especially important for individuals over the age of 35 or persons
with preexisting health problems. Recreation Supply, Inc. assumes no
responsibility for personal injury or property damage sustained by or
through use of this product.
1. This product must be assembled on a flat, level surface to assure its proper function.
2. Clean pads and frame on a regular basis. We recommend warm, soapy water.
Do not use harsh or abrasive chemicals.
3. Inspect and tighten all parts before every use. Replace any worn
parts immediately. Failure to do so may result in serious injury.
4. Keep children away from the BODYCRAFT F602V2 at all times.
5. Keep your hands away from cables and pulleys during operation.
6. Keep your hands away from moving parts other than the designated handles.
7. When adjusting the seat, make sure the spring pin is fully engaged.
If not, the seat may slip and cause serious injury.
8. Make certain all cables are seated within the pulleys before every use.
9. Exercise with care to avoid injury.
10. If you are unsure about the proper use of the BODYCRAFT F602V2 Bench call your
local BODYCRAFT dealer or our customer service department.
As a quality exercise equipment supplier we are committed to your complete
satisfaction. If you have questions, or find missing or damaged parts, we will
guarantee your complete satisfaction through our authorized dealer service
centers or our home office customer service department. Please call your local
dealer for assistance or BODYCRAFT at 800-990-5556 (9 AM - 5 PM) EST. Our
trained technicians will provide immediate assistance to you, free of charge.

F602V2 Bench Assembly Parts List
NOTE: IF A PART IS MISSING, IT LIKELY HAS BEEN PRE-INSTALLED FOR
QUALITY CONTROL PURPOSES. PLEASE PROCEED WITH ASSEMBLY.
(1) BASE
FRAME
(5) SEAT
ADJUSTER
(6) ATTACHMENT
HOLDER
(8) FOAM PAD
HOLDER (2pcs)
(10) LEG/KNEE
HOLD DOWN
(2) FRONT
STABILIZER (3) REAR
STABILIZER
(4) BACK SUPPORT &
(7) BACK ADJUSTER
(Pre-Assembled)
(21) 75 X 45mm
RECT. END
CAP (4pcs)
(23) 45 X 75mm
RECT. END
PLUG (2pcs)
(24) 45 mm
SQ. END
PLUG (3pcs)
(25) 1"
ROUND
PLUG (4pcs)
(31) BACK PAD
(32) SEAT PAD (33) FOAM
ROLLER PAD
(43) KNOB
NO. DESCRIPTION QTY.
2
6
4
12
4
8
1/2" X 5" HEX HEAD BOLT
1/2" X 3" HEX HEAD BOLT
3/8" X 2-3/4" HEX HEAD BOLT
1/2" FLAT WASHER
3/8" FLAT WASHER
1/2" NYLON NUT
51
53
54
55
56
57
(51) (53)
(54) (55) (56) (57)
2
0
(inch) 1" 2" 3"1/21/4 3/4 1/2 1/2 4" 5" 6"1/2 1/2 1/2
*Parts images are not to scale.

3
Recommended Tools
Utility Knife (To cut packaging and banding)
Ratchet with 9/16" and 3/4" Sockets
9/16" and 3/4" Combination Wreches
Adjustable Wrench
Rubber Mallet
Assembly Instructions
NOTE: Before installing the plastic parts, please allow them
to acclimate to room temperature or they may be damaged.
CAREFULLY install all plastic components with Rubber Mallet.
PLEASE REFER TO THE EXPLODED VIEW ON THE NEXT PAGE FOR ASSEMBLY.
1. Carefully install END CAPS(21) onto FRONT STABILIZER(2) and REAR
STABILIZER(3) using a rubber mallet.
2. Bolt the FRONT STABILIZER(2) and REAR STABILIZER(3) to the MAIN FRAME(1),
using four BOLTS(53), eight WASHERS(55) and four NUTS(57). Tighten.
3. Bolt ATTACHMENT HOLDER(6) to MAIN FRAME(1), using two BOLTS(53), four
WASHERS(55) and two NUTS(57). Tighten.
4. Install END PLUGS(23) into SEAT ADJUSTER(5) and BACK SUPPORT(4) using a
rubber mallet.
5. Attach SEAT ADJUSTER(5) and BACK SUPPORT(4) to MAIN FRAME(1), using
BOLT(51) and NUT(57). (NO WASHERS) (Any moving parts that do not pivot freely,
slightly loosen the nuts counterclockwise at the pivot points to allow movement, but
not too much to allow play or wobble.)
6. Attach SEAT PAD(32) to SEAT ADJUSTER(5) and BACK PAD(31) to BACK
SUPPORT(4), using BOLT(54), WASHER(56). Tighten.
7. Install 50mm SPACER CAP(22) onto ATTACHMENT HOLDER(6).

8. Insert LEG/KNEE HOLD DOWN(10) into ATTACHMENT HOLDER(6). Using Pop-Pin.
9. Install END PLUGS(24) into LEG/KNEE HOLD DOWN(10) with Rubber Mallet.
10. Insert FOAM PAD HOLDERS(8) into the LEG/KNEE HOLD DOWN(10) and slide
FOAM ROLLER PAD(33) onto each end of the FOAM PAD HOLDER(8) and secure
with 1" ROUND CAP PLUG(25) using rubber mallet.
11. Install KNOB(43) onto the threaded end of the pre-installed BOLT(63) located at
the lower part of the BACK ADJUSTER(7). Tighten.
ASSEMBLY IS COMPLETE!
PLEASE RECHECK THAT ALL COMPONENTS ARE TIGHT AND SECURE.

10
8
833
33
33
24
24
24
25
33
25
25
25
7
9
57
43
57
55 55
52
55
55
62
4
EXPLODED VIEW
1
2
3
4
5
6
31
32
21
21
21
21
22
23
23
44
54
54
54
56
56
56
57
57
59
59
61
60
60
57
55
55
55
55
55
51
53
53
53
41
42 26

(59) (60) (61)
5
COMPLETE PARTS CHART
(1) (2) (3)
(4) (5) (6)
(7) (8) (9) (10)
(21) (22) (24) (25)(23)
(31) (32) (33)
(51) (52) (53)
(41) (42) (43) (44)
(54) (55) (56) (57)
(58)
NO. DESCRIPTION QTY.
NO. DESCRIPTION QTY.
NO. DESCRIPTION QTY.
NO. DESCRIPTION QTY.
NO. DESCRIPTION QTY.
1
2
3
4
5
6
7
8
9
10
1
1
1
1
1
1
1
2
1
1
MAIN FRAME
FRONT STABILIZER
REAR STABILIZER
BACK SUPPORT
SEAT ADJUSTER
ATTACHMENT HOLDER
BACK ADJUSTER
FOAM PAD HOLDER
BRACE
LEG/KNEE HOLD DOWN
4
1
2
3
4
1
75 X 45mm RECT. END CAP
50mm SPACER CAP
45 X 75mm RECT. END PLUG
45mm SQ. END PLUG
1" ROUND PLUG
38mm SQ. PLUG
1
1
4
BACK PAD
SEAT PAD
FOAM PAD
1
1
1
6
QUICK RELEASE
POP PIN
KNOB
BUSHING
2
1
6
4
12
4
9
1
2
2
2
1
1/2" X 5" HEX HEAD BOLT
1/2" X 4" HEX HEAD BOLT
1/2" X 3" HEX HEAD BOLT
3/8" X 2-3/4" HEX HEAD BOLT
1/2" FLAT WASHER
3/8" FLAT WASHER
1/2" NYLON NUT
1/2" NYLON NUT(THINNER)
WHEEL
5/16" X 1-1/2" HEX HEAD BOLT
5/16" NYLON NUT
1/2" X 6" HEX HEAD BOLT
21
22
23
24
25
26
31
32
33
41
42
43
44
51
52
53
54
55
56
57
58
59
60
61
62
(26)
(62)
*Parts images are not to scale.