Bodypoint BB101M-1 Guide
en
Aeromesh®
Rapid-Dry Bath Belt, Two-Piece
INSTALLATION AND USER’S INSTRUCTIONS
ART NOS. BB101M-1 & BB101L-1
WARNING! Because of the risk of choking,
it is dangerous to use a chest belt without
stabilizing the pelvis – always use with a
USE:
WARNING! This product should only be
used for positioning a person in a shower/
commode chair. It is NOT intended for use as a
transportation safety device, as a personal
restraint device, or in any other application
where its failure could result in injury. Misuse of
this product is unauthorized and unsafe.
WARNING! Accidental release of this
product can allow the user to slip down or fall
from the shower/commode chair. If the user’s
movements or cognitive abilities could lead to
accidental release, a caregiver must be present
at all times during its use. Ensure that all
caregivers know how to unfasten the product.
Failure to do so may delay release in an
emergency.
MAINTENANCE: Check periodically for
signs of wear in the stitching, webbing, and
Bodypoint. Under no circumstance should this
persons – health and safety depend on it!
REGULAR CLEANING: Machine
wash, hot, 60°C (140°F) using laundry deter-
gent. Tumble dry, or drip dry. Do not iron.
SPECIAL CLEANING: For extra
sanitizing, the belt can be machine washed,
very hot, 70°C (160°F) with bleach.
WARRANTY: This product carries a limited-life-
time warranty against defects in workmanship
and materials arising under normal use by the
original consumer. Contact your supplier or
Bodypoint for warranty claims.
For more information on Bodypoint products,
and a list of distributors outside the USA go to
www.bodypoint.com
These instructions provide important information for the safe use and maintenance of all
two-piece Bodypoint Aeromesh® Rapid-Dry Bath Belts. Give these instructions to the user or
their caregiver and review them to ensure that they are understood.
BPI085-en 2015.7
MDSS GmbH
Schiffgraben 41
D-30175 Hannover
Germany
A
N
S
I
|
R
E
S
N
A
I
S
O
T
E
S
T
E
D
PACKAGE CONTENTS
• Aeromesh® Rapid-Dry Bath Belt
• Optional: Frame Clamps (Art. No. HW310),
Band Clamps (Art. No. HW320), Knob (Art. No.
FA812-BP)
POSITIONING
Seat user in shower/commode chair and establish correct
posture. Determine desired position for the belt. When
choosing position, consider interference with other devices.
To reduce the risk of strangulation and trunk instability, the
belt should be neither too high nor too low.
en
CTilting Chairs
Belt must be mounted to the upper frame,
above the pivot point. Mounting the belt
below the pivot point can cause interfer-
ence or affect belt tension.
BAcross Thighs
(Optional)
INSTALLATION
Direct Screw Mounting
If mounting directly to chair frame or solid seats/backs,
use 6mm (1/4-20) Flat head or Button head screws.
Mounting screws must have a minimum pullout
strength of 90kg (200lbs). Not included in package.
AC
B
MOUNTING SUGGESTIONS
AAt Chest, At Knees (Preferred)
suitable mounting location on the wheelchair
that allows the belt to be mounted at one of the
preferred positions shown.
With Frame Clamps or Band Clamps
Attach clamps to shower/commode chair in desired
locations and tighten in place. Insert second screw
through grommet on belt and into the clamp.
Tighten securely.
ADJUSTMENT
grommets.
SAFETY CHECK
When properly positioned in chair, have user lean forward and side-to-side
1. Normal operation of buckle and adjustment straps.
2. Comfort - Look for areas of irritation.
3. Position - If too high or too low, adjust mounting points.
5. Move chair through full range of motion, including tilt, folding, and
rolling. Check for any interference.
Optional
Art No.
FA812-BP
4mm (5/32”)
Other manuals for BB101M-1
1
This manual suits for next models
1
Other Bodypoint Personal Care Product manuals
