Bodypoint BB111 Guide
en
Aeromesh®
Rapid-Dry Bath Belt, One-Piece
INSTALLATION AND USER’S INSTRUCTIONS
ART NOS. BB111 & BB112
WARNING! Because of the risk of choking,
it is dangerous to use a chest belt without
stabilizing the pelvis – always use with a
USE:
WARNING! This product should only be
used for positioning a person in a shower/
a transportation safety device, as a personal
restraint device, or in any other application
WARNING! Accidental release of this
product can allow the user to slip down or fall
movements or cognitive abilities could lead to
accidental release, a caregiver must be present
Failure to do so may delay release in an
MAINTENANCE: Check periodically for
signs of wear in the stitching, webbing, and
persons – health and safety depend on it!
REGULAR CLEANING:
wash, hot, 60°C (140°F) using laundry deter-
SPECIAL CLEANING: For extra
sanitizing, the belt can be machine washed,
WARRANTY: This product carries a limited-life-
time warranty against defects in workmanship
and materials arising under normal use by the
For more information on Bodypoint products,
These instructions provide important information for the safe use and maintenance of all
one-piece Bodypoint Aeromesh® Rapid-Dry Bath Belts. Give these instructions to the user
or their caregiver and review them to ensure that they are understood.
BPI094-en 2015.5
MDSS GmbH
Schiffgraben 41
D-30175 Hannover
Germany
A
N
S
I
|
R
E
S
N
A
I
S
O
T
E
S
T
E
D
PACKAGE CONTENTS
Package may contain one or more of the following:
• Aeromesh® Rapid-Dry Bath Belt
• Mounting straps with grommets, or
• Mounting straps with slide adjuster
• Optional: Frame Clamps (Art. No. HW310),
Band Clamps (Art. No. HW320), Knob (Art. No.
FA812-BP
POSITIONING
Seat user in shower/commode chair and establish
correct posture. Determine desired position for the
belt. When choosing position, consider interference
with other devices. To reduce the risk of strangula-
tion and trunk instability, the belt should be neither
too high nor too low.
en
CTilting Chairs
Belt must be mounted to the upper frame,
above the pivot point. Mounting the belt
below the pivot point can cause interfer-
ence or affect belt tension.
BAcross Thighs
(Optional)
INSTALLATION
Direct Screw Mounting
If mounting directly to chair frame or solid
seats/backs, use 6mm (1/4-20) Flat head or
Button head screws. Mounting screws must
have a minimum pullout strength of 90kg
(200lbs). Not included in package.
MOUNTING SUGGESTIONS
AAt Chest, At Knees (Preferred)
suitable mounting location on the wheelchair
that allows the belt to be mounted at one of the
preferred positions shown.
With Frame Clamps or Band Clamps
Attach clamps to shower/commode chair
in desired locations and tighten in place.
Insert second screw through grommet on
belt and into the clamp. Tighten securely.
Optional
Art No.
FA812-BP
Mounting with Slide
Adjuster
ADJUSTMENT
With the user correctly seated,
be snug so the user is secure. Small
the D-ring tightening straps. Large
mounting straps.
SAFETY CHECK
When properly positioned in chair,
have user lean forward and side-to-
1. Normal operation of buckle and
adjustment straps.
2. Comfort - Look for areas of
irritation.
3. Position - If too high or too low,
adjust mounting points.
Relocate mounting points as
necessary.
5. Move chair through full range of
motion, including tilt, folding, and
rolling. Check for any interference.
AC
B
Other manuals for BB111
2
This manual suits for next models
1
Other Bodypoint Personal Care Product manuals
