Bodypoint EVOFLEX EB205 Guide

en
Evoex®
INSTALLATION AND USER’S INSTRUCTIONS
ART NOS. EB205, EB225, EB235, EB275, & EBE100
Optional Bodypoint belt mounting hardware may
be used for mounting to wheelchairs and seating
systems.
WARNING! Product should be installed and
tted by a qualied rehab technician.
INTENDED USE:
WARNING! This product should only be used
for positioning a person in a wheelchair or work
chair. It is NOT intended for use as a
transportation safety device, as a personal
restraint device, or in any other application where
its failure could result in injury. Misuse of this
product is unauthorized and unsafe.
WARNING! This pelvic positioning belt must
be worn tightly tted across the lower pelvis or
thighs at all times. Have your seating specialist
demonstrate its proper adjustment and use.
• A loose belt can allow the user to slip down
and create a risk of strangulation.
• Accidental release of this belt can allow the
user to slip down or fall from the wheelchair.
• A user’s inability to self-release can be
hazardous if the user slips down or is trapped
in the wheelchair in an emergency.
If the user’s physical or cognitive abilities prevent
them from safely operating this belt, a caregiver
must be present at all times during its use. Ensure
that all caregivers know how to correctly adjust
and unfasten the product.
WARNING! As with any new seating support,
this product may change the way a person sits.
Users must continue to practice regular pressure
relief activities and skin integrity checks, not only
where this product contacts the user, but also in
primary pressure-bearing areas such as the
sacrum, legs, and buttocks. If increased skin
redness or irritation occurs, discontinue use and
consult your physician or seating specialist. Failure
to do so may result in serious injury, such as
pressure ulcers.
WARNING! If a serious incident occurs related
to the use of this product, it should be reported
to the manufacturer (Bodypoint, Inc.) and the local
Competent Authority.
PERIODIC SAFETY AND PERFORMANCE
CHECKS: To ensure user safety, this product
must be checked periodically for function and
signs of wear. If the product does not function
correctly or if signicant wear is found in the
buckles, mounting points, webbing, padding, or
stitches, stop using it and contact your supplier
for qualied repair or replacement by Bodypoint.
Under no circumstance should this product be
altered or repaired by unqualied persons —
health and safety depend on it!
CLEANING: Machine wash, hot,
60°C (140°F). Do not bleach. Tumble dry, low
temperature, or drip dry. Do not iron. (Placing
the product inside a cloth bag during washing
helps prevent scratches to the product and the
machine.)
SCRAP/DISPOSAL: Product is made of materials
which can be disposed of safely without special
precautions at the end of its useful life.
WARRANTY: This product carries a limited
lifetime warranty against defects in workmanship
and materials arising under normal use by the
original consumer. Contact your supplier or
Bodypoint for warranty claims.
These instructions provide important information for the safe use and maintenance of the
Bodypoint Evoex pelvic positioning belt and optional Evoex Belt Extender. Give these in-
structions to the user or their caregiver and review them to ensure that they are understood.
BPI092-en 2021.14© 2021 Bodypoint, Inc. All Rights Reserved.
Bodypoint Europe BV
Kerkstraat 29
7396 PD Terwolde
The Netherlands
Medical
Device
I
S
O
•
A
N
S
I
|
R
E
S
N
A
S
T
A
N
D
A
R
D
S
-
T
E
S
T
E
D

en
4mm (5/32”)
MOUNTING OPTIONS
BELT POSITION
1. Based on clinical goals, determine the most effective position
and angle for the belt. Determine whether putting pull strap on
left or right side is best for user.
2. With the adjustment strap tightened, locate the desired
mounting points on the seating system or wheelchair frame, then
select from the mounting methods shown.
3. Add Evoex Belt Extender if needed to reach mounting points.
DIRECT MOUNTING TO SIDE GUARDS
Drill 6mm (1/4”) hole or use existing hole/slot to
attach belt using included fasteners.
PACKAGE CONTENTS: Package may contain one
or more of the following:
Evoex pelvic positioning belt with:
• (2) M6 x 8 screws
• (2) M6 Low-prole ange nuts
• (2) Wave spring washers
(2) Evoex Belt Extenders with:
• (2) M6 x 8mm screws
• (2) M6 Low-prole ange nuts
4mm (5/32”)
SEAT MOUNTING BRACKET
(Requires Art. No. HW200-20 or -90)
4mm (5/32”)
BAND CLAMP OR FRAME CLAMP
(Requires Art. No. HW320 or HW310)
Attach clamp to seat tube. Attach belt using the
M6 screw included with the clamp.
T-SLOT FASTENER KIT
(Requires Art. No HKA6-12 or HKA10-14)
Use wave spring washer and low-prole ange nut
from Evoex kit with bolt and washer from T-Slot
Fastener Kit.

Ø6mm (1/4”)
CONTROLLING
ROTATION
To increase tension
and control rotation,
use included wave
spring washer. Omit
wave spring washer to
decrease tension and
allow easier rotation.

en
BELT ADJUSTMENT
When the belt is properly adjusted and tightened, it should t
snugly, with all slack removed, so that the user is secure. Use the
pull strap for daily adjustments, such as to accommodate changes
in clothing.If additional length adjustment is necessary to achieve
a good t or to remove the product for cleaning, this can be done
at the end straps.
SAFETY CHECK
When properly positioned in wheelchair, have user lean forward
and side to side to check t. Check for:
1. Normal operation of buckle and adjustment straps.
2. Comfort: Look for areas of irritation.
3. Position: If too high or too low, adjust anchor points.
4. Interference with other devices: Relocate anchor points as
necessary.
5. Move chair through full range of motion, including tilt, folding,
and rolling. Check for any interference and relocate mounting
points as necessary.
EVOFLEX BELT EXTENDER INSTALLATION (OPTIONAL)
Attach Belt Extender to Evoex. Spring washer not used.
To prohibit belt rotation.
(Pin facing in)
MOUNTING
Attach Belt Extender with
Evoex to wheelchair
using one of the methods
shown under Mounting
Options. (Spring washer
optional.)
Cut to length as needed
using a saw. Ensure cut
location is as far away as
possible from mounting
hole being used.
4mm (5/32”)
Apply
threadlocker
INSTALLATION
To allow belt rotation. (Pin facing out)