Boneco S250 User manual

S250
MANUAL
READ AND SAVE THESE INSTRUCTIONS

Instructions for use 3
Mode d’emploi 11
Instrucciones de uso 19

3
en
BONECO S250
INSTRUCTIONS FOR USE

4
en ITEMS INCLUDED AND TECHNICAL DATA
BONECO S250 2 × anti-mineral pad Printed quick start guide 1 × “EZCal” descaling powder
TECHNICAL DATA*
Mains voltage 120V / 60 Hz
Power consumption 145W / 285W
Humidity output 1.8 gal/ day
For rooms up to 430 sq ft (40 m2)
Water capacity 0.8 gal (3.0 liters)
Dimensions L×W×H 12.4×6.8×11 in. (316×172 ×281 mm)
Weight (empty) 5.5 lb (2.5 kg)
Operation noise level <35 dB(A)
System Steamer
* Subject to change
ITEMS INCLUDED

5
en
OVERVIEW AND PART NAMES
5
6
1
2
3
41Water tank inspection glass
2Operation indicators
3Control panel
4Steam outlet
5Water tank
6Air inlet

6
en PUTTING INTO OPERATION
Plug the power cord into a power outlet.
Place the BONECO S250 on a stable surface. Fill the water tank with cold tap water.
1
4
2 3
5 6
Control the steam output using the button. Select the desired humidity level using the
and buttons.
Switch on the BONECO S250 by pressing the
button.

7
en
DISPLAY AND HANDLING
Symbol Meaning
Humidity
Display shows the current humidity
Display shows the set humidity
High (H) or low (L) steam output
Note: Refill the water
Note: Cleaning required
Button Function
On/Off, starts cleaning function
Controls steam output
Sets the desired humidity
Overview of all indicators on the display

8
en HANDLING
CONTROLLING HUMIDITY
The BONECO S250 is equipped with a hygrostat that con-
tinuously monitors the humidity in the room and regulates
the unit's operation. The adjustable range is between
30% and 70%.
1. Switch on the BONECO S250.
2. Use the and buttons to set the desired hu-
midity. The display shows the note ("de-
sired").
3. A few seconds after the last input, the display
changes back to . The display now shows
the current humidity again.
The BONECO S250 stops humidification once the desired
value is reached. Humidification continues automatically
as soon as the set value is no longer met.
REGULATING OUTPUT
The performance of the BONECO S250 is regulated in
two levels.
1. Press the button to switch between the two per-
formance levels.
The selected level is shown on the display by the symbols
(“High”) and (“Low”).
The selected level does not affect the measurement or the
control functions of the hygrostat.

9
en
SAFETY INSTRUCTIONS
Always unplug the BONECO S250 before you start
cleaning it! Failure to do so can result in electric
shock and fatal injury!
Do not use alcohol or corrosive cleaning agents for
cleaning.
CLEANING THE HOUSING
In most cases, a dry cloth can be used for cleaning. If
stubborn dirt is present, clean the housing using a damp
cloth. Add a small amount of dishwashing detergent to
the water. Household cloths and window cleaners can
also be used.
REPLACING THE ANTI-MINERAL PAD
The anti-mineral pad absorbs lime in the water so that it
is not released into the ambient air. Over time, the anti-
mineral pad becomes hard and less effective due to the
absorbed lime.
Check the anti-mineral pad after each cleaning. Replace
the anti-mineral pad if it feels hard and rigid. You can
find replacements at your BONECO specialist dealer or in
our online store at this address: www.shop.boneco.us
CLEANING

10
en
PROCEDURE
Although the anti-mineral pad absorbs most of the lime
in the water, the heating plate of the BONECO S250 ex-
periences calcification after an extended operating time.
An upcoming need for cleaning is indicated on the display
by the symbol.
To make descaling easy and convenient, the BONECO
S250 is equipped with an automatic cleaning function.
This warms and cools the heating plate multiple times in
order that the lime becomes crumbly and can be easily
removed.
STARTING THE CLEANING
1. Switch off the BONECO S250 and let it cool down for
1 hour.
2. Remove the anti-mineral pad and empty the water
tank.
3. Mix 1 bag EZCal®with 32 oz. (1 liter) of warm tap
water.
4. Add the mixture to the BONECO S250.
5. Press the button for 3 seconds to start the clean-
ing.
6. Select the duration of cleaning you want (1 to 9 hours)
using the and buttons. If stubborn mineral de-
posits are left after cleaning, you can always extend
or repeat the cleaning process.
7. Unplug the BONECO S250 and rinse the water tank
with tap water.
8. Place the anti-mineral pad back into the water tank.
CLEANING FUNCTION