Bonsaii C144-E User manual

= bonsaii
Paper Shredder C144-E
Instruction Manual
18-Sheet Cross Cut Shredder
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP IT FOR FUTURE REFERENCE.
Please give us a chance to make it right and do better! Customer Service:
Contact our friendly customer service department for help first. % : [email protected]
Replacements for missing or damaged parts will be shipped. Q, : 1-844-728-6917

KNOW YOUR SHREDDER
@ Control Panel( with "Power™FWD™REV" three
buttons and with "BIN FULL™ OVERLOAD/
OVERHEAT"FWD™REV" four indicator lights
@ Feed Opening
@ Basket Handlebar
@ Transparent Window
©® Basket
® Caster Brake
@ Shredder's Caster
For safety reasons, shredder
will operate only if the
shredder head is in correct
position and used with
supplied basket.
TECHNICAL SPECIFICATIONS
Voltage 120V~, 60Hz, 5.5A
Feeding Opening 18 sheetslt Feed Opening | 228 x 5mm
Capacity (A4 75g/m?) sheets/time (Lw) 8.98 x 0.2Inches
Shredding Speed | 1.8m/min Shred Type Cross cut
Basket Capacity 7.1Gallon/27L Shred Paper Size | 0.16x0.47Inches(4x12MM)
14.96 x 12.6 x 22.83 Inches
Product Size (LW'H) | 350'y 320 % 580(mm)

OPERATING INSTRUCTIONS
BIN FULL
OVERLOAD
S
OVERHEAT
1. Switch on the rated power supply, tum the switch of the warping board on the right side of the back to
"I", the Power,FWD and REV indicator light will be on, Shredder is in standby state.
2. Press "FWD " key, the "FWD'indicator light will be in Green;Press "REV " key, the "REVindicator light
will be in Green
3. When the paper is more than the "Max sheets”, the shredder will automatically reverse after protection
The red light of overload/overheating indicator is "flashing". At this time, you need to take out the paper
and work again after the overload/overheating indicator is off.
4. When the motor overheat protection, overload/overheating indicator red "steady on”, at this time the
shredder stops working, need to wait for overload/overheating indicator off before working again
5. When the basket is full, the BIN FULL indicator will be on and the Shredder will stop working. At this
time, the basket should be taken out for cleaning. When the basket is pulled out, the BIN FULL indicator
light s off, and the power indicator light, FWD and REV indicator light are shining (" door opening
function "). When the basket is reassembled in place, the Shredder enters the standby state

TROUBLESHOOTING
Malfunction Reason Solution
Th ! it 1 Please kindly check whether you
e power plug doesn't connect | 56 the machine with related supply|
to the power supply. voltage or Plug in again correctly.
Power supply voltage is too low | Please kindly find a related supply
or no power supply. voltage to use it .
The machine is under overheating
| protection, because the machine is| Wait for the machine to cool down
Stop Working | over the continues working naturally.
capacity.
The thickness of paper is too thin. To make the paper thicker ,You can
add more papers or fold the paper.
P Reduce paper quantity with an
ggsar:::w‘?p':::fi':o:\irg' acceptable amount and place the
! : | paper into the feeding opening of
machine Max shredding quaniities.| g oo oo
Please replace the power cable with
Damage of power cable. the same parameters by professional
person or contact with our
customer service.
The basket is full. Empty the basket.
e EIEEie Please kindly contact with our
- customer service.
. Please kindly use the function of
Jam Paper jam. "Reverse" to take out the excess
paper.
.| Paper dust and other foreign Please unplug first and use soft
Keep Running objzcls SR G, < cloth to clean the foreign objects
without any cleaner or water.
Loud Noise The ;hredder is placed on an Change the location.
unsuitable place.
If the above answers can not solve your problems, please kindly contact with our
customer service team via email [email protected]