Bonsaii C169-B User manual

Customer Service: customer-c[email protected]
1-844-728-6917
Ins
C169-B Paper Shredder
14 Sheets Cross Cut

1
Dear customer,
Thank you for buying this quality product. Please read this ins arefully
befor a ake note of the following safety
ins eep this ins or future reference and pass it, when
handing over this item.
1. K welry , hair or other
small items away from the feed opening to prevent injury.
2. K edder is not in use for prolonged periods
3. Do not place hands or fingers into the shredder throat as serious injury
could result.
4. Always turn off or unplug the shredder prior to moving, cleaning or emptying
the wastebasket.
5. Empty wastebasket frequently.
6. The document shredder must alway ated and disconnected from
the electrical line prior to moving, tr vice and
prior to emptying the wastebasket.
7. Please do not leave the document shredder una ended. E.g. in the event
children and pets are nearby.
8. This machine is able to shred paper, clips, staples and credit cards.
9. The device may not be operated with a damaged power cord.
10. For indoor use only.
11. This machine is no toy. Keep it away from children and pets.
12. Please do not spray any flammable gas or oil onto this shredder, it may
cause fire.
13. Please read the manual before opera
14. Sharp edges. Do not touch .
15. This equipment is not intended for use by children. Avoid touching the media
feed opening with the hands. clothing or hair. Unplug this equipment when not
in use for an ext

2
16. Shred width of 13/64X1-37/64 inches .
17. 14-sheet capacity .
P
A: Feed Slot: Paper, clips, staples and Credit Cards
B: Switch-AUTO / OFF / REV
C: LED indicator lamps -Overheat/ Overload / Power

3
Unpack and set machine upright.
Put the machine on a horizontal surface.
Plug in the machine.
The socket-outlet should be installed near the equipment and shall be easily
accessible
Installa
Please check the voltage of your shredders carefully before using.
On the top of the shredder, there are three (3) se UTO, OFF and REV.
1. When AUTO is selected, the shredding process is started automa ally by
to the feed opening. The shredder will stop automa ally
when the paper has completed its travel through the feed opening.
2. REV is used to assist in the removal of a paper jam, which reverses the shredder
process prior to a completed cy ers. If you want to stop
shredding the paper, please set it to reverse. The machine will reverse
automa ally and turn back the papers.
3. OFF is used to terminate the power to the shredder. This mode is recommended
when emptying the wastebasket or when the shredder is not in use for a
prolong
Opera edder
C169-B will shred fourteen(14) sheets of A4 size 75g/m² paper at once and will
accept paper widths up to 8.66 inches. When shredding small material like
envelopes or receipts, insert them through the middle of the feed opening.
Shredder capacity
C169-B is equipped with a motor overheat prot echnology er
con erheat' LED indicator lights up. Please
remember to stop the machine from working a er the 'Overheat' LED indicator
lights up. Please wait and allow the machine to cool down and restart when the
'Overheat' LED indicator turns off.
Overheat Prot

4
C169-B is equipped with an overload prot echnology. The maximum
shredding capacity of this machine a ourteen (14) sheets of A4 size
75g/m² paper. Exceeding the shredding capacity e. e than fourteen
(14) sheets at one pass, or if the paper is not fed squarely into the feed opening,
the 'Overload' LED indicator lights up and machine starts to reverse automa ally.
Pull the r ers, reduce the number of sheets and
place the paper back into the feed a lot.
Overload Prot
To ensure proper opera ystem is
required Failure to oil y ystem could result in reduced sheet capacity
performance, excess noise, paper jams and possibly machine failure. Oil your
ers ev ou empty the basket, if excess squeaking and
rubbing noise is coming from the machine or if the shredders sheet capacity has
diminished. Squeeze the lubricant acr ers. Push the
switch to 'AUT at ystem
forward for 3 seconds. Then push the switch t o make shredder
reverse for 3 seconds. Alternate between AUTO and REV at least thr
un ers.
er Oiling Ins
Never use flammable synthe troleum based or aerosol lubricants to oil
yystem. It is recommended to use Bonsaii Shredder Lubricant Oil or
Sheet for oiling the shredder.
It is not advised to cut as many sheets as indicated as the maximum capacity of
the shredder. By e t its top capacity we significantly reduce
its vitality. Therefore, to maintain a durable and faultless work of the shredder, it is
advised to place no more than 70% of the maximum amount of sheets to be shred
aated for each model by the producer. The maximum amount of
sheet should be used only occasionally. It is forbidden to shred more sheets than
the maximum amount of sheets to be shred a ated by the producer.
It may cause the blockage of the machine and massive engine overloading, which
BASIC EXPLOITATION RULES

5
will diminish shredder's durability or even damage it. Also you should not shred
oil, paper towels, toilet paper or fabrics. Nor paper with self-
adhesive tape should be placed into the shredder. Those materials wrap around
and jam the knives.
Warranty
The warranty for this appliance is for 12 months from the date of purchase from an
authorized dealer. The appliance has been manufactured with care and me
examined before delivery. Please retain your receipt as proof of purchase. In the
case of a warranty claim, please make contact with our Customer Service
The warranty covers only claims for material and manufacturing defects, but not for
transport damage, wearing parts or for damage to fragile components, e. ons
or ba eries. This product is for domes tended for
commercial use. The warranty is void in the case of abusive and improper handling,
use of force and internal tampering not carried out by our authorized service
branch. Your statutory rights are not restricted in any way by this warranty. The
warranty period is not extended by repairs made under the warranty. This applies
also to replaced and repaired parts.
Specifica
Shred type:
Shredding size:
Noise Level:
Shred capacity:
Feed Opening:
Input:
Shredding speed:
Basket capacity:
Cross cut
13/64 x 1-37/64 inches
58dB
14 sheets 75g/m²
8.66 inches
120V~ 60Hz 2A
1.8m/min
4.8 Gallons

6
The shredder is placed on unsuitable
place.

7
: 4198 Industry Way, Flowery
Branch, GA, 30542, USA
: customer[email protected]
Bonsen Electronics Inc.
: 1-844-728-6917
Made in Vietnam