Borri B 200 User manual

Important Safety Warnings
This manual contains instructions and warnings that should be followed during the
installation, operating and storage of the UPS system. Please keep this manual for
further reference.
C UTION! To prevent the risk of fire or electric shock, install in a temperature and humidity
controlled indoor area free of conductive contaminants. (See the specifications for the
acceptable temperature and humidity range)
C UTION! To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and
avoid e posing the unit to direct sunlight or installing the unit near heat emitting appliances
such as radiators.
C UTION! Do not plug the UPS input into its own output.
C UTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages
or any other liquid-containing vessels on or near the unit.
C UTION! In the event of an emergency, press the OFF button and disconnect the power
cord from the AC power supply to completely disable the UPS.
C UTION! The UPS installation must be correctly grounded in order to reduce leakage current
below 3.5mA.
ttention! The UPS output is supplied by two sources. When the UPS is disconnected from
mains power, hazardous voltage may still be present from the internal battery. The battery
should be disconnected when maintenance or service work inside the UPS is necessary.
C UTION! Servicing of batteries should be performed or supervised by personnel only.
C UTION! When replacing the batteries, use the same number and type of batteries.
C UTION! Dispose of batteries in the correct manner and in line with local laws and
regulations. Never dispose of batteries in a fire. Do not attempt open the battery. Released
electrolyte is harmful to the skin and eyes.
C UTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
C UTION! A battery can present a risk of electric shock and short circuit.
Borri Ltd Borri S.p.
Systems House Via 8 Marzo, 2
Rotherside Road 52010 Bibbiena
Eckington Arrezzo
Sheffield Italy
S21 4HL
UK
Tel: [phone] Tel: [phone]
Fa : [phone] Fa : [phone]
Web: www.borri.co.uk Web: www.borri.it
Specifications
MODEL B200-1000 B200-1500 B200-2000
C P CITY 1000VA / 700W 1500VA / 1050W 2000VA / 1400W
INPUT
Input Voltage 220/230/240 VAC
Voltage Range 162-290 VAC
OUTPUT
Voltage Regulation +/-10%
Transfer Time Typical 2-6 ms, 10 ms ma .
Waveform Pure Sine Wave
B TTERY
Type & Number 12 V/7 AH 2 12 V/9 AH 2 12 V/10 AH 2
Charging Time 4-6 hours recover to 90% capacity
PHYSIC L
Dimension (W D H) mm 146 350 160 146 397 205
Net Weight (KG) 9 12 14
Borri B200 Uninterruptible Power Supply
User Manual

Installation & Operation
 Initial Set-up
After unpacking the unit, please avoid placing the unit in direct sun light, e cessive heat,
e cessive humidity or in contact with fluids of any type. Please allow 20cm space around the
unit.
 Connect Mains Power
Plug the UPS into an electrical outlet that does not share a circuit with a other heavy electrical
load. Please allow the UPS to charge at least 6 hours prior to use.
 Connect Equipment
Connect critical equipment to the battery backup outlets; these are supported automatically by
the battery when a mains failure occurs. Connect other equipment that needs only surge
suppression to the surge protected outlets. Power is not supplied to these outlets when the
unit is switched off. Therefore, please be sure to switch on the unit.
NOTE: Please DO NOT connect scanners or printers to the battery backup outlets.
 Connect Modem/Phone/Network for Surge Protection
Connect a single modem/phone line into surge-protected “IN” outlet on the back panel of the
UPS unit. Connect from “OUT” outlet to the computer with another phone line cable.
Connect Communication Port
To allow for unattended UPS shutdown/start-up and status monitoring, connect the
communication cable one end to the USB port and the other to the communication port of your
PC. With the monitoring software installed, you can schedule UPS shutdown/start-up and
monitor UPS status through PC.
Software Installation
1) Please download the monitoring and shutdown software from the website
http://www.borri.co.uk/softwaredownload to download ViewPower software.
2) When your computer restarts, the monitoring software will appear as an orange plug icon
located in the system tray, near the clock.
Power On/Off UPS
Press power switch on the front panel of the UPS to turn on the UPS. Press switch again to turn
off the UPS.
Front Panel & Back Panel
LCD panel
Power switch
B200-1000 B200-1500/2000
Troubleshooting
Problem Possible Cause Solutions
The front panel in blank.
Low battery. Charge the UPS at least 6 hours.
Battery fault. Replace the battery with the same
type of battery.
The UPS is not turned on. Press the power switch again to turn
on the UPS.
Alarm sounds
continuously when the
mains is normal.
The UPS is overload. Remove some loads first. Before
reconnecting equipment, please
verify that the load matches the UPS
capability specified in the specs.
When power fails,
back-up time is short.
The UPS is overload. Remove some critical load.
Battery voltage is too low. Charge the UPS at least 6 hours.
Battery d
efect. It might be due
to high temperature operation
environment, or improper
operation to battery.
Replace the battery with the same
type of battery.
The mains is normal but
UPS is on battery mode.
Input power cable is loose. Reconnect the input power cable
properly.
LCD Panel:
 Input voltage  Load level indicator, flashing
 Output voltage indicates overload
 AC mode indicator
 Battery capacity indicator, flashing
 Battery mode indicator indicates low battery

Battery backup receptacles

Surge protected receptacles
 AC input

USB communication port
 Modem/Phone Line/Network
surge protection