Bosch eplus ACTIVE LINE User manual

INSTALLATION
BOSCH
ENGINES
[email protected] // www.eplus.bike
Via Pontestura 124 Camino 15020 (AL) Italy
eplus
ACTIVE LINE
PERFOMACE LINE
PERFOMACE LINE CX
3.07 VERSION

2. INSTALLATION
INSTALLATION
Connection
ATTENTION
It is forbidden by law to activate EPLUS speed unlocker in public places such as streets,
squares and cycling paths. So it is only possible to activate EPLUS speed unlocker in private
places such as circuits and private properties.
The manufacter denies responsibility due to any damage to pedal assisted bicycles
where Eplus is set up. The manufacter denies responsibility due to any harm to people or
objects.
Unplug the connectors
Looking at the bike from behind, on the left side (opposite side to the chainring),
remove the 3 Torx screws (T20) that hold the protective cap of the Bosch engine
(in this case Performance CX).
1
Remove the battery from e-bike

3. INSTALLATION
2
3
After removing the protective cover, identify the two plugs of the display (the second
connector from left of 4 wires colored: yellow-green-black-red) and the speed sensor
(2 wire plug fully right: black-red).
With a long forceps carefully remove the two plugs paying attention not to pinch
them ruining plugs or wires.

4. INSTALLATION
4
Insert the thermoshrinking sheath (enclosed) in the two disconnected wires,
pushing it over the plug.
5
Insert plugs (output cables from the chip) in their respective two sockets
(cables disconnected from the engine) respecting the correct wire color: DISPLAY PLUG >
YELLOW-YELLOW / GREEN-GREEN / BLACK-BLACK / RED-RED
AND SPEED SENSOR PLUG > BLACK-BLACK / WHITE-RED
USE EXTREME ATTENTION TO CORRECTLY ASSEMBLE THE COLORS! CAUTION: WRONG
CONNECTION LEADS TO SHORTCIRCUIT, DAMAGES NOT COVERED BY WARRANTY!

5. INSTALLATION
SPEED SENSOR
SOCKET
SPEED SENSOR
PLUG
HMI (DISPLAY)
PLUG
HMI (DISPLAY)
SOCKET
TO THE DISPLAY
(HMI) PLUG:
RED => RED
BLACK => BLACK
GREEN => GREEN
YELLOW => YELLOW
(SEE PHOTO 5)
TO THE SPEED
SENSOR PLUG:
BLACK => BLACK
RED => WHITE
(SEE PHOTO 5)

6. INSTALLATION
6
Carefully cover the two plugs with shrink wrap and with a hair dryer or a lighter heat uniformly the
sheath (turning it from right to left) until you have the sheath that takes the shape of the plugs.
Be careful not to burn wires or plugs.
7

7. INSTALLATION
Now connect the two plugs remaining on the chip to the engine, respecting the correct posi-
tion of the colors (display RED WIRE and speed sensor WHITE WIRE get to the RIGHT) and push
the connectors rmly to the end; CAUTION: WRONG CONNECTION LEADS TO SHORTCIRCUIT,
DAMAGES NOT COVERED BY WARRANTY!
8
WHITE WIRE TO RIGHT
RED WIRE TO RIGHT
9
Possibly arrange the cables with electrician clamps paying attention that there are no wires in
correspondence with holes where cover’s screws are and close it gently.

8. INSTALLATION
The engine unlock at 25 km / h is activated by pressing the Walk button on the
on-board computer. The activation button can be changed (see pag. 9).
The display will show the value 2.2 if the unlock has been activated and 1.1 if it is
deactivated.
Racing Speed Unlocker/Advanced is compatible with Purion, Nyon and Intuvia
displays.
If you have Intuvia or Nyon displays, for correct operation follow the instructions
on page. 9/10.
RACING MODE
AC TIVATION OF
THE SPEED UNLOCK
DATA VIEW ON THE DISPLAY
Purion: correct speed, correct km done
Intuvia: correct speed, correct km done, total km 00
Nyon: correct speed, km done with unlock activated halved

9. INSTALLATION
MENU O.5 - For changes to the factory settings
The SPEED UNLOCKER chip, factory mode, is set to be switched on / o using the WALK button
and calibrated for 27.5 “wheels (2170 mm in circumference) and to be used with Purion/Nyon
Display.
To change the default parameters follow the next procedure scrupulously:
1. Turn on the display and place the aid level in OFF mode
2. Press the [-] button on the handlebar 4/5 times until the number 0.5 appears on the display
3. 3. Move the [+ -] keys on the handlebar and enter the menu to be modied choosing between
1,2,3,4,5,6 (large number on display).
parameter [0.5] > For INTUVIAvisualization of total km done; for PURION/NYON the partial
•
and total km will be visible asusual on the display;
parameter [1.5] > Display Type (only Bosch) 1.1 Purion/Nyon (default) 2.2 Intuvia; 3.3 Nyon
•
parameter [2.5] > Choice of wheel circumference size:•
wheel circumference (default value > 21.7 equivalent to 2170 mm or 27.5” standard•
wheel) the value must be as close as possible to the real circumference in order to have a
correct reading of the speed. The use of automatic calibration is recommended (parameter
4.5);
parameter [3.5] > Choice of activation/deactivation unlock button: you can change the
•
default setting (default value> 4.4 WALK key) by choosing: 1.1 RESET key, 2.2 LIGHT key, 3.3
sequence+++ or 4.4 WALK.1.1 RESET button , 2.2 LUCI (LIGHTS) button , 3.3 sequence +++
or 4.4. WALK.
CHANG ES TO THE
YOUTUBE VIDEO:
https://youtu.be/qr_QfI5uDdc

10. INSTALLATION
FACTORY SETTINGS
parameter [4.5] > Automatic calibration of wheel circumference: If the bike is stopped, the•
message 55.6 will appear on the display for a few seconds, at the end of calibration 50.1
appears. If the bike is moving or the magnet on the spokes is positioned above the sensor,
calibration is NOT STARTED and 99.9 appears on the display;
parameter [5.5] > Km Reset ODO and TRIP calculated in unlocker mode;
•
parameter [6.5] > software version•
4. Make the choice and wait for about 5-10 seconds to enter the parameter to be modied.
5. Change the value with the [+ -] keys as desired: then wait a few seconds until the value is
positioned at 0.0.
For Intuvia displays
1. Modify the default parameters by specifying you will be using an Intuvia display ( see point 3,
parameter [1]
2. At rst use you’ll have to reset Trip.
3. For technical reasons, only on Intuvia display, the total distance will start from ‘0’ and will
increase until the bike is switched o . When you turn the bike on again, the value will restart
from ‘0’. In order to visualize the total kms travelled, it will be necessary to press the INFO button
and position on the ‘TOTAL KM’, then follow Point 3, parameter [0]
4. The partial Km will continue to increase until they are not put back to zero with the RESET
button.
Attention: the visualization of the total Km travelled will be possible only after having covered
at least 100 km
For Nyon display
it is necessary to change the factory parameters specifying that the Nyon display is used. See
point 3, parameter 1.5
Warning: the Nyon display will show the correct speed and the kilometers done with the unlock
activated halved.
YOUTUBE VIDEO:
https://youtu.be/qr_QfI5uDdc