Bosch AMC2-4WE User manual

AMC2 Extension
AMC2‑4WE
en Installation Manual

AMC2 Extension Table of contents | en 3
Bosch Access Systems GmbH Installation Manual 2018-02 | AMC2-4WE |
Table of contents
1Safety Instructions 4
1.1 Important Safety Notes 4
1.2 Safety Precautions 5
1.3 Unpacking 6
2Important Information 7
2.1 Explanation of symbols in this document 7
2.2 Internet 7
3Introduction 8
3.1 Description 8
3.2 Equipment Configuration 9
3.3 Performance Characteristics 10
3.4 System Overview 10
4Installing 12
4.1 Mounting 12
4.2 Unmounting 13
4.3 Opening the Case 14
4.4 Closing the Case 15
4.5 Cabling 15
4.5.1 Conductor data for power to AMC2 15
4.6 Grounding and Shielding 17
4.6.1 Grounding for Extension Interface 17
4.7 Connecting Power Supply 18
4.7.1 Direct Power Supply 18
4.7.2 Power Supply via RS-485 Interface 18
4.7.3 Overview - Power supply/consumption 19
4.8 RS-485 for extension modules 21
4.9 Wiegand Interface for Card Readers 22
4.10 Connecting Relay Outputs 22
4.11 Connecting Analog Input Devices 26
4.12 Tamper Protection 28
5Operating 29
5.1 Status Display of the AMC2 29
6Technical Data 31
7Appendices 33
7.1 Connecting Diagrams 33
Index 36

4en | Safety Instructions AMC2 Extension
2018-02 | AMC2-4WE | Installation Manual Bosch Access Systems GmbH
1 Safety Instructions
1.1 Important Safety Notes
1. Read, follow, and retain instructions - All safety and operating instructions must be read
and followed properly before putting the unit into operation. Retain instructions for
future reference.
2. Do not ignore warnings - Adhere to all warnings on the unit and in the operating
instructions.
3. Accessories - Use only accessories recommended by the manufacturer or those sold with
the product. Accessories not recommended by the manufacturer must not be used, as
they may cause hazards.
4. Installation precautions - Do not place this unit on an unstable stand, tripod, bracket, or
mount. The unit may fall, causing serious injury to persons and damage to the unit. Mount
the unit according to the manufacturer’s instructions.
5. Service - Do not attempt to service this unit by yourself. Opening or removing covers may
expose you to dangerous voltages or other hazards. Refer all servicing to qualified service
personnel.
6. Damage which requires service - Disconnect the unit from the main AC or DC power
source and refer servicing to qualified service personnel under the following conditions:
– If the power supply cord or plug is damaged.
– If liquid has been spilled or an object has fallen into the unit.
– If the unit has been exposed to water and/or inclement weather (rain, snow, etc.).
– If the unit does not operate normally when following the operating instructions.
Adjust only those controls specified in the operating instructions. Improper
adjustment of other controls may result in damage, and require extensive work by a
qualified technician to restore the unit to normal operation.
– If the unit has been dropped or the cabinet damaged.
– If the unit exhibits a distinct change in performance.
7. Replacement parts - If replacement parts are required, the service technician must use
only replacement parts that are specified by the manufacturer. Unauthorized
replacements may result in fire, electrical shock or other hazards.
8. Safety check - Upon completion of service or repair work on the unit, ask the service
technician to perform safety checks to ensure that the unit operates properly
9. Power sources - Operate the unit only from the type of power source indicated on the
label. If unsure of the type of power supply to use, contact your dealer
10. Lightning - For added protection during electrical storms external lightning conductors
can be installed. This prevents power surges from damaging the unit.
11. The units should be installed in locations with restricted access.

AMC2 Extension Safety Instructions | en 5
Bosch Access Systems GmbH Installation Manual 2018-02 | AMC2-4WE |
1.2 Safety Precautions
Read instructions!
Before working with the AMC2 device, read these instructions carefully. Make sure you have
understood all information described in this document.
!
Warning!
Risk of electric shock
External power supplies must be installed and put into service by qualified personnel.
Ensure compliance with the relevant regulations.
Ground the controller.
Disconnect both AC and battery power supply before working on the controller.
!
Warning!
Risk of fire
Installation of the AMC2 device must comply with any local fire, health, and safety
regulations. A secured door that may be part of an escape route from an area must be
installed with:
Install a fail-safe lock (A), so that the door will be released if power fails. Ideally, use a
magnetic lock.
Install a normally-closed break glass or a manual pull (B) in the lock supply wiring, so that in
an emergency the fail-safe lock can be immediately powered down.
!
Warning!
Risk of explosion of Lithium battery
The battery can explode if it is replaced incorrectly.
Replace only with the same type as recommended by the manufacturer.
Dispose used batteries according to the battery manufacturer’s instructions.
Notice!
Risk of damage to equipment
Protect the hardware from electrostatic discharge by observing ESD instructions before
unpacking of touching connectors of electronics.
Always switch off power of the AMC2 device before modifying the installation.
Do not connect or disconnect plug connectors, data cables, or screw connectors while power
is on.
Rules and Conditions
There are no specific requirements as for selling and delivery. As for storage and safe
operation, the environmental temperature should not exceed the range of 0°C to 50°C.
Disposal
Your Bosch product is designed and manufactured with high-quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should be
disposed of separately from your household waste.

6en | Safety Instructions AMC2 Extension
2018-02 | AMC2-4WE | Installation Manual Bosch Access Systems GmbH
In the European Union, there are separate collection systems for used electrical and electronic
products. Please dispose of this equipment at your local community waste collection/recycling
center.
1.3 Unpacking
Check the packaging for visible damage. If anything has been damaged during transport,
please inform the transport agency.
Unpack the unit carefully. This is an electronic device that must be handled with care to avoid
damage. Do not attempt to put the unit into operation if components are damaged.
If any parts are missing, inform your customer service representative or a Bosch Security
Systems salesperson. The shipping carton is the safest transport container for the unit. Store
it and the other packaging material for future use. If the unit has to be sent back, use the
original packaging.

AMC2 Extension Important Information | en 7
Bosch Access Systems GmbH Installation Manual 2018-02 | AMC2-4WE |
2 Important Information
Remarks
This hardware is part of a security system. Access should be limited to authorized persons
only.
Some states do not allow the exclusion or limitation of implied warranties, or limitation of
liability for incidental or consequential damages, hence the above limitation or exclusion might
not apply to you.
Bosch Security Systems retains all rights not expressly granted. Nothing in this license
constitutes a waiver of Bosch’s rights under the U.S. Copyright laws or any other federal or
state law.
If you have any questions concerning this license, please, write to:
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany.
2.1 Explanation of symbols in this document
Throughout this document, warning messages, important notes, and helpful tips are presented
for the reader. These appear as follows:
Danger!
Cause of Hazard
Indicates a hazardous situation, which, if not avoided, will result in death or serious injury.
!
Warning!
Cause of Hazard
Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
!
Caution!
Cause of Hazard
Indicates a hazardous situation, which, if not avoided, could result in minor or moderate
injury.
Notice!
Cause of Hazard
Important Notes that must be followed to avoid damage to the equipment or environment,
and to ensure successful operation and programming.
Tips and shortcuts may also be included in such notes.
2.2 Internet
If you are interested in further information on this product or information on other products,
please consult our website at http://www.boschsecurity.com.

8en | Introduction AMC2 Extension
2018-02 | AMC2-4WE | Installation Manual Bosch Access Systems GmbH
3 Introduction
3.1 Description
The extension module AMC2-4WE is equipped with four Wiegand type reader-interfaces plus
eight inputs and eight outputs. Hence with the AMC2-4WE it is possible to double the number
of readers on an AMC2-4W from 4 to 8.
Figure3.1: The extension module AMC2-4WE
The AMC2-4WE can not be deployed as an independent controller but only as an extension
module for the AMC2-4W. Control and access decisions and bookings are carried out by the
AMC2-4W alone.
Notice!
The AMC2-4WE can only be used with AMC2-4W. As it provides Wiegand interfaces it cannot
be coupled with an AMC2-4R4.
The AMC2-4W can be extended by a maximum of one AMC2-4WE plus a maximum of three I/O
extension modules. The I/O extension modules AMC2-8IOEAMC2-16IOE (in any combination)
are, like the AMC2-4WE, connected via the AMC2-4W’s extension interface.
Notice!
The AMC2-4WE has no display. The information about the input and outputs will be shown on
special pages of the AMC2 display.
As the extension modules contain neither memory nor display they are controlled and
monitored entirely by the AMC2-4W.
The AMC2-4W can have an additional interface extension module AMC2-4WE, so that the
number of inputs and outputs can grow up to 64.
Notice!
An AMC2-4WE provides signals only to the AMC2 to which it is connected. Signal transfer to
another AMC2 is not possible.
The signal settings and parametrization of the readers connected to the extension module, are
carried out by the configuration applications in the access control system and by the
AMC2-4W to which it belongs.

AMC2 Extension Introduction | en 9
Bosch Access Systems GmbH Installation Manual 2018-02 | AMC2-4WE |
3.2 Equipment Configuration
Figure3.2: Overview - Interfaces
1RS-485 extension module bus
2External tamper contact
3Connector for power supply
4Wiegand interfaces for up to 8card readers
5Connectors for eight analog inputs
6Connectors for eight relay outputs
Figure3.3: Jumpers at the bottom side
7Jumper for setting either voltage free relay output (“dry” mode) or looped-in voltage
from the AMC2 internal power supply (“wet” mode).
8Jumper: Equalization of potential between different systems and earth ground
(shield) for the extension interface.

10 en | Introduction AMC2 Extension
2018-02 | AMC2-4WE | Installation Manual Bosch Access Systems GmbH
3.3 Performance Characteristics
– Controlled by an AMC2 via RS-485
– Reader interfaces
– four two Wiegand interfaces
– Eight relay outputs
– voltage free, power is supplied externally (dry mode)
– powered by internal power supply (wet mode)
– Eight analog inputs with internal power supply
– Transfer rate to the extension interface: 9,6 kBit/s
– Self regulating transmit/receive switching
– Power supply:
– 10V - 30Vdc - max. 5 A
– or over the RS-485 host connector
– Information about the inputs and outputs on the display of the AMC2 controller
– Tamper contact for external covers
Notice!
If an external power supply is used, this should also guarantee an uninterruptable power
supply (UPS). Example: Bosch power supply APS-PSU-60 (F.01U.282.970).
3.4 System Overview
The AMC2-4WE is connected between the access controller AMC2-4W and the various
peripheral devices.
Figure3.4: System overview
1 = Host
2 = AMC2-4W
3 = Card reader
4 = Communication and power supply
5 = AMC2-4WE