Bosch Access Modular Controller 2 User manual

Access Modular Controller 2
API‑AMC2‑16ION
en Installation manual

Access Modular Controller 2 Table of contents | en 3
Bosch Access Systems B.V. Installation manual 2020-01 | V02 |
Table of contents
1Safety Instructions 4
1.1 Important safety notes 4
1.2 Safety precautions 5
1.3 Unpacking 6
2Important Information 7
2.1 Explanation of symbols in this document 7
2.2 Internet 7
3Introduction 8
3.1 Description 8
3.2 Equipment Configuration 8
3.3 Performance Characteristics 11
3.4 System Overview 11
4Installing 13
4.1 Mounting 13
4.2 Unmounting 14
4.3 Opening the Case 15
4.4 Closing the Case 16
4.5 Cabling 16
4.5.1 Conductor data for power to AMC2 16
4.6 Grounding and Shielding 18
4.6.1 Grounding for Host Interface 18
4.6.2 Grounding for Extension Interface 19
4.7 Connecting Power Supply 20
4.8 Ethernet Host Interface 21
4.9 RS-485 Host Interface 22
4.9.1 RS-485 Two Wire Connection 23
4.9.2 RS-485 Four Wire Connection 23
4.10 RS-232 Host Interface 24
4.11 DIL switch selector 25
4.11.1 Host settings 25
4.11.2 Board Settings 26
4.12 RS-485 for extension modules 26
4.13 Connecting Relay Outputs 28
4.14 Connecting Analog Input Devices 31
4.15 Tamper Protection 33
5Operating 34
5.1 Status Display of the AMC2 34
5.2 Configuring the Ethernet Interface 36
5.3 Troubleshooting 36
5.3.1 Resetting the Software 36
5.3.2 Resetting the Device to Factory Default 37
6Technical Data 38
7Appendices 41
7.1 Connecting Diagrams 41
Index 45

4en | Safety Instructions Access Modular Controller 2
2020-01 | V02 | Installation manual Bosch Access Systems B.V.
1 Safety Instructions
1.1 Important safety notes
1. Read, follow, and retain instructions - All safety and operating instructions must be read
and followed properly before putting the unit into operation. Retain instructions for
future reference.
2. Do not ignore warnings - Adhere to all warnings on the unit and in the operating
instructions.
3. Accessories - Use only accessories recommended by the manufacturer or those sold with
the product. Accessories not recommended by the manufacturer must not be used, as
they may cause hazards.
4. Installation precautions - Do not place this unit on an unstable stand, tripod, bracket, or
mount. The unit may fall, causing serious injury to persons and damage to the unit. Mount
the unit according to the manufacturer’s instructions.
5. Service - Do not attempt to service this unit by yourself. Opening or removing covers may
expose you to dangerous voltages or other hazards. Refer all servicing to qualified service
personnel.
6. Damage which requires service - Disconnect the unit from the main AC or DC power
source and refer servicing to qualified service personnel under the following conditions:
– If the power supply cord or plug is damaged.
– If liquid has been spilled or an object has fallen into the unit.
– If the unit has been exposed to water and/or inclement weather (rain, snow, etc.).
– If the unit does not operate normally when following the operating instructions.
Adjust only those controls specified in the operating instructions. Improper
adjustment of other controls may result in damage, and require extensive work by a
qualified technician to restore the unit to normal operation.
– If the unit has been dropped or the cabinet damaged.
– If the unit exhibits a distinct change in performance.
7. Replacement parts - If replacement parts are required, the service technician must use
only replacement parts that are specified by the manufacturer. Unauthorized
replacements may result in fire, electrical shock or other hazards.
8. Safety check - Upon completion of service or repair work on the unit, ask the service
technician to perform safety checks to ensure that the unit operates properly
9. Power sources - Operate the unit only from the type of power source indicated on the
label. If unsure of the type of power supply to use, contact your dealer
10. Lightning - For added protection during electrical storms external lightning conductors
can be installed. This prevents power surges from damaging the unit.
11. The units should be installed in locations with restricted access.

Access Modular Controller 2 Safety Instructions | en 5
Bosch Access Systems B.V. Installation manual 2020-01 | V02 |
1.2 Safety precautions
Read the instructions
Before working with the AMC2 device, read these instructions carefully. Make sure you have
understood all information described in this document.
!
Warning!
Risk of electric shock
External power supplies must be installed and put into service by qualified personnel.
Ensure compliance with the relevant regulations.
Ground the controller.
Disconnect both AC and battery power supply before working on the controller.
!
Warning!
Risk of fire
Installation of the AMC2 device must comply with any local fire, health, and safety
regulations. A secured door that may be part of an escape route from an area must be
installed with:
Install a fail-safe lock (A), so that the door will be released if power fails. Ideally, use a
magnetic lock.
Install a normally-closed break glass or a manual pull (B) in the lock supply wiring, so that in
an emergency the fail-safe lock can be immediately powered down.
!
Warning!
Risk of explosion of Lithium battery
The battery can explode if it is replaced incorrectly.
Replace only with the same type as recommended by the manufacturer.
Dispose used batteries according to the battery manufacturer’s instructions.
Notice!
Risk of damage to equipment
Protect the hardware from electrostatic discharge by observing ESD instructions before
unpacking of touching connectors of electronics.
Always switch off power of the AMC2 device before modifying the installation.
Do not connect or disconnect plug connectors, data cables, or screw connectors while power
is on.
Rules and Conditions
There are no specific requirements as for selling and delivery. As for storage and safe
operation, the environmental temperature should not exceed the range of 0°C to 50°C.
Disposal
Your Bosch product is designed and manufactured with high-quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should be
disposed of separately from your household waste.

6en | Safety Instructions Access Modular Controller 2
2020-01 | V02 | Installation manual Bosch Access Systems B.V.
In the European Union, there are separate collection systems for used electrical and electronic
products. Please dispose of this equipment at your local community waste collection/recycling
center.
1.3 Unpacking
Check the packaging for visible damage. If anything has been damaged during transport,
please inform the transport agency.
Unpack the unit carefully. This is an electronic device that must be handled with care to avoid
damage. Do not attempt to put the unit into operation if components are damaged.
If any parts are missing, inform your customer service representative or a Bosch Security
Systems salesperson. The shipping carton is the safest transport container for the unit. Store
it and the other packaging material for future use. If the unit has to be sent back, use the
original packaging.

Access Modular Controller 2 Important Information | en 7
Bosch Access Systems B.V. Installation manual 2020-01 | V02 |
2 Important Information
Remarks
This hardware is part of a security system. Access should be limited to authorized persons
only.
Some states do not allow the exclusion or limitation of implied warranties, or limitation of
liability for incidental or consequential damages, hence the above limitation or exclusion might
not apply to you.
Bosch Security Systems retains all rights not expressly granted. Nothing in this license
constitutes a waiver of Bosch’s rights under the U.S. Copyright laws or any other federal or
state law.
If you have any questions concerning this license, please, write to:
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany.
2.1 Explanation of symbols in this document
Throughout this document, warning messages, important notes, and helpful tips are presented
for the reader. These appear as follows:
Danger!
Cause of Hazard
Indicates a hazardous situation, which, if not avoided, will result in death or serious injury.
!
Warning!
Cause of Hazard
Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
!
Caution!
Cause of Hazard
Indicates a hazardous situation, which, if not avoided, could result in minor or moderate
injury.
Notice!
Cause of Hazard
Important Notes that must be followed to avoid damage to the equipment or environment,
and to ensure successful operation and programming.
Tips and shortcuts may also be included in such notes.
2.2 Internet
If you are interested in further information on this product or information on other products,
please consult our website at http://www.boschsecurity.com.

8en | Introduction Access Modular Controller 2
2020-01 | V02 | Installation manual Bosch Access Systems B.V.
3 Introduction
3.1 Description
The AMC2-16ION board provides inputs and outputs to control doors and other components
independent of access control system.
Figure3.1: The IO-Controller AMC2-16ION
The AMC2-4R4 standalone board (hereafter also referred as AMC2 or controller) are deployed
via a dedicated OPC-Server. Though similar in appearance to the AMC2-4W and AMC2-4R4
controllers, the AMC2-4R4 has no reader interfaces, but is intended instead for the efficient
monitoring and control of many devices, especially entrances, simultaneously. It is not an
extension board like the AMC2-16IOE, AMC2-8IOE, and AMC2-16IE but possesses its own CPU
and host interfaces.
The AMC2-4R4 has 16 analog inputs and 16 relay outputs. Via its inputs the module can
determine the status (e.g. locked, closed or open) of entrances, windows or other devices,
and its output signals can lock/unlock doors, or trigger alarms with external monitoring
systems in the case of an intrusion.
If the 8 and the 8 outputs are insufficient for your needs, then up to three extensions
(AMC2-16IOE , AMC2-8IOE, or AMC2-16IE) can be connected, thus providing the AMC2-4R4
with a maximum of 64 inputs and 64 outputs for configuration.
3.2 Equipment Configuration
Figure3.2: Circuit board with display (top side)
1(N.A.)
2DIL switch for RS-485 address selection , protocol, and RS-232/RS-485 selection.

Access Modular Controller 2 Introduction | en 9
Bosch Access Systems B.V. Installation manual 2020-01 | V02 |
3Lithium battery for buffering of static RAM and real time clock (RTC). The battery life
is estimated at 10 years, nevertheless an error message is generated if the voltage
sinks below a preset minimum level.
NOTICE: In order to avoid an error message caused by an earlier voltage drop we
suggest to replace the battery every 8 years. Spare part: VARTA CR 2032 PCB.
4Reset push button - reachable through the casing using a screwdriver
5Liquid Crystal Display
6Push button, available on top of the housing, to select different display modes
7Jumper: Equalization of potential between different systems and earth ground
(shield)
8Jumper: Interface selector RS-485 host connection, RS-485 two wire or RS-485 four
wire (depends on external wiring)
9Configurable RS-485 host interface
10 Docking port for compact flash memory
11 Configurable RS-232 host interface (ribbon cable connector)
12 Configurable 10/100 Mbit/s Ethernet host interface
Figure3.3: Overview - Interfaces
13 RS-485 extension module bus
14 External tamper contact
15 Connector for power supply
16 Connectors for eight analog inputs
17 Connectors for eight relay outputs
Notice!
All connectors, with the exception of the RS-232 and Ethernet host interface, are pluggable
screw clamp terminals.

10 en | Introduction Access Modular Controller 2
2020-01 | V02 | Installation manual Bosch Access Systems B.V.
Figure3.4: Jumpers at the bottom side
18 Jumper for setting either voltage free relay output (“dry” mode) or looped-in voltage
from the AMC2 internal power supply (“wet” mode).
19 DIL switch for setting the board address.
20 Jumper: Equalization of potential between different systems and earth ground
(shield) for the extension interface.
Notice!
For details on the setting of the jumpers and DIL switches listed here, please see DIL switch
selector, page 25.