Bosch D8108A User manual

1 | Overview
2 | Installation
3.55 in.
16 in.
16 in.
1
4
3
2
5
6
3
6
3
The D8108A/D8108A-CE Attack
Resistant Enclosures house many Bosch
Security Systems, Inc. control panels.
When housed in a D8108A/D8108A-
CE, a listed control panel can be used
in a high-security mercantile alarm
application. For specific control panel
applications, refer to the operation and
installation manual for the control panel.
The D8108A-CE enclosure includes a
transformer for CE installations.
Figure 1.1: Mounting the enclosure and installing accessories
Callout ― Description
1 ― Tamper switches (2)
2 ― 1 in. (2.5 cm) 6-32 screws (6) and nuts (6) for the tamper switches
3 ― 7/8 in. (2.2 cm) 8-32 machine screws (5)
4 ― D101 Lock and key (P/N: 4998800200)
5 ― Tamper switch mounting holes
6 ― Knockouts
Two knockouts in the enclosure base
(one in the top, the other in the bottom)
accommodate ¾ in. (2 cm) conduit.
The enclosure door is slotted to enable
conduit access.
1. Attach the lead wires to the
terminals on the two tamper
switches and wire them in series
with an EOL resistor.
2. Using the supplied hardware,
screw the tamper switches to the
enclosure (screws on the outside
and the nuts on the inside).
3. Mount the lock for UL Burglary
and Fire applications on the
enclosure door.
4. Mount the enclosure to a hard,
flat surface.
5. Mount the control panel (with
the mounting skirt) inside the
enclosure.
6. Wire, program, and test the
control panel and related
peripheral equipment.
7. Wire the tamper switches to a
control panel protective zone or
point input.
8. Close the enclosure door.
9. Install the supplied 7/8 in. (2.2
cm) 8-32 screws in the five
locations, securing the door to the
base and making the enclosure
attack resistant.

© 2016 Bosch Security Systems, Inc. 4998132018 | 06 | 2016.05
en Installation Guide
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450
USA
www.boschsecurity.com
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
Copyright
This document is the intellectual property of Bosch Security Systems, Inc. and is protected by copyright. All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered trademarks and must be treated
accordingly.
Bosch Security Systems, Inc. product manufacturing dates
Use the serial number located on the product label and refer to the Bosch Security Systems, Inc. website at
http://www.boschsecurity.com/datecodes/.
Attack Resistant Enclosure
D8108A/D8108A-CE
Dimensions 16 in. x 16 in. x 3.5 in. (41 cm x 41 cm x 9 cm)
Color Grey
Compatible Tamper Switches D110 (P/N: 4998137947) or
ICP-EZTS (P/N: F01U217038)
D101 Lock and Key (included) (P/N: 4998800200)
6 | D8108A Specifications
Region Certification
USA UL 294 - Access Control System Units
UL 365 - Police Station Connected Burglar Alarm Units and Systems
UL 609 - Local Burglar Alarm Units and Systems
UL 864 - Control Units and Accessories for Fire Alarm Systems
UL 985 - Household Fire Warning System Units
UL 1023 - Household Burglar-Alarm System Units
UL 1076 - Proprietary Burglar Alarm Units and Systems
UL 1610 - Central Station Burglar Alarm Units
CSFM - California Office of The State Fire Marshal
FDNY
CA Canada CAN/ULC S303 - Local Burglar Alarm Units and Systems
CAN/ULC S304 - Signal Receiving Centre and Premise Alarm Control
Units
ULC-ORD C1023 - Household Burglar Alarm System Units
4 | D8108A certifications
Region Certification
Europe CE
5 | D8108A-CE certifications
Dimensions 16 in. x 16 in. x 3.5 in. (41 cm x 41 cm x 9 cm)
Color Grey
Compatible Tamper Switches D110 (P/N: 4998137947) or
ICP-EZTS (P/N: F01U217038)
D101 Lock and Key (included) (P/N: 4998800200)
Transformer (included) (P/N: F01U166215)
7 | D8108A-CE Specifications
3 | Wire a D8108A-CE to a
control panel
Wire the D8108A-CE transformer to
the control panel after completing the
instructions in Section 2.
2
LN
3
4
USB POWER
STATUS
B
A
S
E
L
I
N
KT
ETHERNETUSB
EARTH GROUND
COMMON
BATTERY ( - )
+ AUX POWER
BATTERY ( + )
CLASS 2
16.5 VAC 40 VA 60 Hz
TRANSFORMER
10
9
8
7
6
5
4
3
2
1
WARNING!
Multi-Battery
installation requires
Model D122 or D122L
Dual Battery Harness.
Improper installation
can be a fire hazard .
Low 12.1 VDC
Load Shed 10.2 VDC
OUTPUT
B (2)
OUTPUT
A (1)
OUTPUT
C (3)
1
Figure 3.1: Wiring the D8108A-CE
Callout ― Description
1 ― Low voltage AC
2 ― Ground wire connection
3 ― AC IN
4 ― Wire tie the AC IN wires to the
enclosure lance