Safety
Caution!
Remove all power (AC and battery) before mak-
ing any connections. Failure to do so might res-
ult in personal injury and/or equipment dam-
age.
Introduction
Attack resistant enclosure to contain and protect compat-
ible control panels in high-security mercantile alarm ap-
plications. The D8108A-CE version includes a transformer
for CE installations.
System overview
3.55 in.
16 in.
16 in.
1
4
3
2
5
6b
3
6a
3
1 Tamper switches (2)
2 1 in. (2.5 cm) 6-32 screws (6) and nuts (6) for the
tamper switches
3 7/8 in. (2.2 cm) 8-32 machine screws (5)
4 D101 Lock and key
5 Tamper switch mounting holes
6a Enclosure base knockout (top) for ¾ in. (2 cm) con-
duit
6b Enclosure base knockout (bottom) for ¾ in. (2 cm)
conduit
Installation
1. Attach the lead wires to the terminals on the tamper
switch and wire in series with an EOL resistor.
2. Push the tamper switch screws through the mounting
holes in the top of the enclosure and through the
holes in the tamper switch.
3. Place and tighten the tamper switch nuts on the
screws to attach the tamper switch to the enclosure.
4. Install the lock on the enclosure door for UL burglary
and fire applications.
5. Install the control panel and mounting skirt inside the
enclosure.
6. Wire, program, and test the control panel and related
peripheral equipment.
7. Wire the tamper switch to a control panel protective
zone or point input.
8. Close the enclosure door.
9. Push the machine screws through the door and en-
closure holes to attach the door to the enclosure
base.
D101 lock installation
D101 embedded installation video
ICP-EZTS tamper switch installation
ICP-EZTS tamper switch embedded installation video
Transformer wiring diagram
2
L N
3
4
USB POWER
STATUS
B
A
S
E
L
I
N
KT
ETHERNETUSB
EARTH GROUND
COMMON
BATTERY (
-
)
+ AUX POWER
BATTERY ( + )
CLASS 2
16.5 VAC 40 VA 60 Hz
TRANSFORMER
10
9
8
7
6
5
4
3
2
1
WARNING!
Multi-Battery
installation requires
Model D122 or D122L
Dual Battery Harness.
Improper installation
can be a fire hazard
.
Low 12.1 VDC
Load Shed 10.2 VDC
OUTPUT
B (2)
OUTPUT
A (1)
OUTPUT
C (3)
1
1 Low voltage AC
2 Ground wire connection
3 AC IN
4 Wire tie the AC IN wires to the enclosure lance
Technical data
Dimensions 16 in. x 16 in. x 3.5 in. (41
cm x 41 cm x 9 cm)
Color White
Compatible Tamper
Switches
D110 (P/N: 4998137947) or
ICP-EZTS (P/N:
F01U217038)
D101 Lock and Key Included (P/N:
4998800200)
Transformer Included with D8108A-CE
only
D8108A certifications
Region Certification
US UL 294 - Access Control System Units
UL 365 - Police Station Connected Burglar Alarm
Units and Systems
UL 609 - Local Burglar Alarm Units and Systems
UL 864 - Control Units and Accessories for Fire
Alarm Systems
UL 985 - Household Fire Warning System Units
UL 1023 - Household Burglar-Alarm System Units
UL 1076 - Proprietary Burglar Alarm Units and
Systems
UL 1610 - Central Station Burglar Alarm Units
CSFM - California Office of The State Fire Mar-
shal
FDNY
Canada CAN/ULC S303 - Local Burglar Alarm Units and
Systems
CAN/ULC S304 - Signal Receiving Centre and
Premise Alarm Control Units
ULC-ORD C1023 - Household Burglar Alarm Sys-
tem Units
D8108A-CE certifications
Region Certification
Europe CE
