Bosch ISC-PPR1-W16G User manual

ISC-PPR1-W16G
Installation Instructions
Professional Series
PIR Detector
EN

1.0 General Information
The ISC-PPR1-W16x Professional Series PIR Detectors
are exceptionally suited for commercial indoor applications.
Sensor data fusion technology ensures that the detec-
tors send alarm conditions based on precise information.
Tri-focus optics eliminate coverage gaps and respond
efciently to intruders. The powerful combination of unique
features in the Professional Series delivers superior catch
performance and virtually eliminates false alarms.
The self-locking two-piece enclosure, built-in bubble level,
exible mounting height, and three optional mounting
brackets simplify installation and reduce service time.
2.0 Installation Procedure
Do Not:
• Mount outdoors
• Point toward windows
• Install facing direct sunlight
• Point towards replaces or air conditioners
• Install near moving objects such as ceiling fans
The ISC-PPR1 is immune to small animals weighing less
than 10 lb. (4.5 kg). The small animal immunity feature was
not investigated by UL.
Mount the detector so that it is between 7 ft and 10 ft from
the oor (2.1 m - 3 m).


Mount the detector so that a person walks across the de-
tection pattern.
Typical mounting locations
1.1 Unlock and remove the cover
The cover lock snaps back to the locked position when the
cover is removed. The cover must be reattached with the
lock in the locked position.
2.2 Mounting Level
The detector has a built-in level which can be moved to
measure on two axes.


2 © 2009 Bosch Security Systems, Inc.

2.3 Mounting the detector
Use the hardware provided. The plastic mounting anchors
require a 3/16 (5 mm) hole.
Surface mounting
1 Tamper Screw
Corner Mounting
2.4 Wiring the detector
Wire sizes between 16 AWG and 26 AWG (0.2 mm2and 1
mm2) are permitted. Install the wiring using the approprate
knock-outs and tie-downs.
© 2009 Bosch Security Systems, Inc. 3
2.5 Wiring the terminal blocks
The detector has two terminal blocks. One block is used for
primary wiring; the other has two spare terminals. The two
spare terminals are normally used as tie points for the EOL
resistor.
Do not attempt to remove the terminal blocks from
the cover. This could result in permanent damage
to the detector.

4 © 2009 Bosch Security Systems, Inc.
3.0 Switch Settings
3.1 Switch 1 - Walk Test
Switch 1 Voltage on WT
Terminal Walk Test
ON 0 ON
ON +12 OFF
OFF 0 OFF
OFF +12 ON
The Remote Self Test automatically occurs when the walk
test changes from a disabled to enabled by a change in the
voltage on the WT terminals.
The Remote Self Test must be connected to 0 or +12 VDC
on UL listed Control Panels.
3.2 Switch 2 - Alarm Memory Polarity
Switch 2 Voltage on S/U
Terminal Alarm Memory
ON +12 ON (Locked)
ON 0 OFF (Unlocked)
OFF 0 ON (Locked)
OFF +12 OFF (Unlocked)
The Alarm Memory must be connected to 0 or +12 VDC on
UL listed control panels.
3.3 Switch 3 - Short Range/
Long Range
Switch 3 Range Distance
ON Short 25 ft (8 m)
OFF Long 50 ft (16 m)
4.0 LED Indicators
Color Indication Function
Blue Steady ON New alarm detected
Blue
Flashing 1/4
sec ON, 1/4
sec OFF
Alarm Memory
Blue 4 Flashes Self Test/
Self Test failure
Blue 5 Flashes Low Input Power
A passing Remote Self Test responds with an
alarm signal.

© 2009 Bosch Security Systems, Inc. 5
5.0 Setup
5.1 Walk Test
If Switch 1 is ON and no connections are made to
the WT terminal, the local Walk Test is always on. For
switch settings refer to Section 3.1 Switch 1 - Walk Test on
page 4.
To perform the Walk Test, walk across the detection
pattern.
5.2 Alarm Memory
If Switch 2 is ON and no connections are made to the
S/U terminal, the Alarm Memory is OFF. For switch set-
tings refer to Section 3.2 Switch 2 - Alarm Memory Polarity
on page 4.
Alarm memory ashes the alarm LED to indicate stored
alarms for use in multiple unit applications. A switched
voltage from the control panel controls the alarm memory.
The Alarm Memory function is used when more than one
detector is connected to an alarm loop. The Alarm Memory
identies the units experiencing an alarm in the last armed
period. The detector stores the alarm event in memory
during the armed period. It shows the stored alarm when
the system is disarmed. The LED ashes to indicate the
stored alarm. Alarm Memory clears when the system is re-
armed.
5.3 Trouble Memory
Pulsing the WT Terminals recalls the last trouble condition
from the memory. Refer to Section 4.0 LED Indicators on
page 4 for the trouble conditions.
When the memory is recalled, it clears automatically after
12 hours.
5.4 Short Range/Long Range
For switch settings refer to Section 3.3 Switch 3 - Short
Range/Long Range on page 4. If Switch 3 is in the ON
position the coverage pattern is 25 ft x 33 ft (8 m x 10 m). If
Switch 3 is in the OFF position the coverage pattern is 50 ft
x 70 ft (16 m x 21 m).

© 2009 Bosch Security Systems, Inc. 7/09
130 Perinton Parkway, Fairport, NY 14450-9199 USA Page 6 of 6
[phone]
6.0 Specications
Electrical
Power Requirements
Voltage (Operating): 9 VDC to 15 VDC
Current (Maximum): 15 mA. Current (Standby): 10 mA
Outputs
Relay: Solid state relay, normally-closed (NC) contacts
power supervised.
3 W, 125 mA, 25 VDC, resistance < 10 Ω.
Tamper: Normally-closed (NC) contacts (with cover on)
rated at 25 VDC, 125 mA maximum.
Connect tamper circuit to 24-hour protection circuit.
Trouble: Solid-state relay normally-closed (NC) contacts.
Mechanical
Enclosure Design
Color: White
Dimensions: 5.0 in. x 2.75 in. x 2.25 in.
(127 mm x 69 mm x 58 mm)
Material: High-impact ABS plastic
Indicators
Alarm Indicators:
• Blue LED for alarms
Detection Zones
Zones: 86
Frequency Information
Radio Frequency Interference (RFI) immunity:
No alarm or setup on critical frequencies in the range from
26 MHz to 1 GHz at 50 V/m.
Environmental
Relative Humidity: 0 to 95%, non-condensing
Temperature (Operating and Storage):
-20°F to +130°F (-29°C to +55°C)
For UL Certicated installations, +32°F to +120°F (0°C to
+49°C)
Environmental Class II EN 50130-5
Protection Rating: IP41, IK04 (EN 60529, EN 50102)